Introduce configuration for STM32 MINI A15 embedded development
board. The board has a STM32F103VET6 MCU on board. The MCU has 64KB of
SRAM and 512KB of flash.
The board has the following peripherals:
- RS232 port on DB9 connector, connecting to USART1, pin mapping:
- PA9-US1-TX
- PA10-US1-RX
- a LED diode (U2) connected to pin PB5
- micro SD card connector with pin mapping:
- PC8-SDIO-D0
- PC9-SDIO-D1
- PC10-SDIO-D2
- PC11-SDIO-D3
- PC12-SDIO-CK
- PD2-SDIO-CMD
- on board SPI flash AT45DB161D-SU, pin mapping;
- PA4-SPI1-NSS
- PA5-SPI1-SCK
- PA6-SPI1-MISO
- PA7-SPI1-MOSI
- button (K1), connecting PB15 to GND
- 40-pin header connector XS5
Change-Id: Ia378b105abb25fb589a100185ea96512a5f98cf3
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Quark AON counter and timer sub-drivers. They are based
on the QMSI drivers.
In order to enable this driver, the following options
must be set.
CONFIG_QMSI_DRIVERS
CONFIG_QMSI_INSTALL_PATH
CONFIG_COUNTER
Origin: Original
Change-Id: Idbeabfaef3408f4d645b0e64a337d7f5f0f357c7
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
All driver APIs (i2c, spi, gpio, etc.) return 'int' type, but pinmux
APIs. So this patch changes the returning type from 'uint32_t' to
'int' from include/pinmux.h and fixes all pinmux drivers according.
Besides keeping consistency between all drivers APIs, this patch is
also applicable for the errno.h code transition. Pinmux drivers will
return negative errno.h codes so returning 'int' is more suitable
than 'uint32_t'.
Change-Id: I2a6e92d567a0e21fec363226da6197df94657d4b
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This adds a menu to enclose all board Kconfig. So the board
configs do not appear on the top level out of context in
menuconfig. This also reflects the SoC options where these are
under menus for each architecture.
Change-Id: I76ce2bf1acf7cbd2673ceb2eac71e96cdca2ff35
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This makes the board selection dependent on SoC selection. For example,
select Atmel SAM3 will only allow "Arduino Due" as board selection.
This disallows incompatible SoC/board combination, like K64F with
Arduino Due.
JIRA: ZEP-106
Change-Id: I675961cf33db5a0058fc68f14c8f16978f9c6b95
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This board is now part of qemu_x86 and shares the same file except
the configuration which makes it build with IAMCU.
JIRA: ZEP-103
Change-Id: I9a9911d013b493240c089ce71e9f95687dcc02a3
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Making pinmux depend on GPIO breaks many tests and configurations
when running on real hardware. This should be added as local
configuration in the defconfig instead.
Change-Id: Ibbf1c9a3428ed692937383bf85218b0c120cbe44
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
CONFIG_HPET_TIMER_LEVEL_LOW and CONFIG_HPET_TIMER_RISING_EDGE are
selected from same choice option so cannot be both selected.
Since HPET_TIMER_FALLING_EDGE is the default only options overriding
this were left in defconfig files.
Fix following:
Merging prj_x86.conf
.config:10:warning: override: HPET_TIMER_RISING_EDGE changes choice
state
Change-Id: I5c88d2c0ae309afa11d9fae116235a8a424a2408
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Many bugs that have taken months to tease out could have been
instantly exposed had we run all our sanity checks on this
ABI.
Origin: Original code or copied from boards/qemu_x86
Change-Id: I6a5038bf99379470c3f736857d104024d3fc7978
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The pinmux API was modified to expand the meaning of the 'func' argument
to allow it to represent more than a pre-configured function. This was done
to reasonably accommodate a larger range of pin configuration options
offered by other MCUs, such as the Freescale K64 (up to 8 pin functions,
plus interrupt, pullup/down, drive strength, open-drain, slew rate, etc.).
This allows bit fields to be used to define various settings.
Change-Id: I2b216b822c6bae7133eed01c8c3339bb47b6c5db
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
In the pinmux_dev driver for the Quark SE development board in
pinmux_dev_set() the variable 'mode' was used, but it should have been
'func'. This was causing a compilation error:
/home/vinicius/work/zephyr/boards/quark_se_devboard/pinmux.c:
In function 'pinmux_dev_set':
/home/vinicius/work/zephyr/boards/quark_se_devboard/pinmux.c:245:23:
error: 'mode' undeclared (first use in this function)
uint32_t mode_mask = mode << (pin_no << 1);
Change-Id: I5b9df7c6b488dc5b8819fcf59bb3b994d9d4820b
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Enable support for WinBond W25QXXDV SPI flash on
arduino 101 platform.
Change-Id: Ia4dc73f956f79c6a56a31bc3dfca4e5298447742
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
The peripherals utilizing UART were required to register their own
ISR rountines. This means that all those peripherals drivers need
to know which IRQ line is attached to a UART controller, and all
the other config values required to register a ISR. This causes
scalibility issue as every board and peripherals have to define
those values.
Another reason for this patch is to support virtual serial ports.
Virtual serial ports do not have physical interrupt lines to
attach, and thus would not work.
This patch adds a simple callback mechanism, which calls a function
when UART interrupts are triggered. The low level plumbing still needs
to be done by the peripheral drivers, as these drivers may need to
access low level capability of UART to function correctly. This simply
moves the interrupt setup into the UART drivers themselves. By doing
this, the peripheral drivers do not need to know all the config values
to properly setup the interrupts and attaching the ISR. One drawback
is that this adds to the interrupt latency.
Note that this patch breaks backward compatibility in terms of
setting up interrupt for UART controller. How to use UART is still
the same.
This also addresses the following issues:
() UART driver for Atmel SAM3 currently does not support interrupts.
So remove the code from vector table. This will be updated when
there is interrupt support for the driver.
() Corrected some config options for Stellaris UART driver.
This was tested with samples/shell on Arduino 101, and on QEMU
(Cortex-M3 and x86).
Origin: original code
Change-Id: Ib4593d8ccd711f4e97d388c7293205d213be1aec
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
That implementation is not galileo-specific, but rather a generic way of
rebooting an x86 target. Needs SoC support.
Change-Id: I9c3374a8ab57a624d9d9b7090260c5b11fe4e773
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
CC2520 can handle up to 8Mhz SPI SCLK frequency, thus let's use it. It
will help to avoid timing issuse while transmitting and receiving (i.e.:
getting registers or buffers from CC2520 through SPI will be fast and
won't impede RX/TX events too much).
Change-Id: I3391993e25ffbe166028923b9afb777a8451a35e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Base address registers and IRQs are set in Kconfig.
Set proper SPI default to various quark_se_ss based boards.
Change-Id: Iadaae551f441457bef334f94f68cafa7c3e499d0
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Quark SE development board provides an ARC core and thus requires a
board definition so developpers can flash this core as well.
Change-Id: I3612e3b0c4d7085af4fcf3fa1f6233849a05c8b4
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This board is not supported and not available for general public.
Use the Quark SE CRB/Devboard instead.
Change-Id: Id0f8c08bbacb812ef00fe9502b4acecf4f31ffd7
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There can only be one instance of an ADC, but we have code setup for
multiple.
Change-Id: I94eae2450bdc6b138ebad66f80a7c451cefe32a9
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
The radio driver was using DW spi and gpio drivers hardcoded.
Now it will check if SPI_DW or SPI_QMSI is set.
Change-Id: I4e12ef7c071058218c1cc714c62fed90a9f5eb06
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Using level will just flood the handler, as the concerned gpio pins
stays on level for some time.
Change-Id: I991d818783170b09c326350c04bb588c7324892c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fixing the flash script so that we only have one for the process of writing
out the ROM and the OS images.
Change-Id: I6fc8bd8eee553a17c0036da3ce5b89510f3b57d8
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
- Use interface script from openocd distribution
- add debug support
Change-Id: If7e0ab0ad1fc6e67ca648a0a7c32356b3db90cf0
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
First pass at a script/process that an end user can run to backup and restore
the binary state of an Arduino 101 system.
Change-Id: I5979bdea5aaa2a77b0e0bb0e44de65ba74cbfd65
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
As the UART uses I/O port access, it needs to be pointed out
to override default MMIO setting.
Change-Id: Ibf923b5cab547f9eec991900c5f7a8b2ffbc3832
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Add tester support for arduino_101 board reusing UART1.
Change-Id: Ifc00f92a80accffc37fd9b09df798ff995340a1c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Using the latest SDK (0.7.2) you can flash directly using make
by specifying the board, for example
make BOARD=arduino_101 flash
This will build and flash the generated binary to the board.
Change-Id: I90254abd69874efbb449ef318079958980c23074
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This adds the pinmux driver for use with Arduino Due.
The default for pinmux (mostly) reflects the pin layout
on the board.
Change-Id: I80827ee8bc507567e0cc04b3c8c48580aadf2b3f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Move BLE configuration to board and enable GPIO for NBLE.
Change-Id: I99c309656430936edf6766fc99fe83b011801bb4
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Set options and baud rate to communicate with NBLE chip.
Change-Id: I338aad3b1dc03b809aade29eedac7093ea346a5e
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This is the last step before obsoleting DEVICE_DEFINE() and
DEVICE_INIT_CONFIG_DEFINE().
Change-Id: Ica4257662969048083ab9839872b4b437b8b351b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_DEFINE() so that it fits in the 'device' namespace.
Change-Id: I3af3a39cf9154359b31d22729d0db9f710cd202b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_INIT_CONFIG_DEFINE(), because (a) it was not fitting
in any namespace and (b) it is not used to declare, but rather define a
object.
Change-Id: I1da5822f06b85a9fb024b5b184afd0ccc01012ec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
SPI needs to get its interrupt configured as triggering on level high to
work properly. This is specific to Quark SE (thus x86 core).
Change-Id: If3921240709e0fbf5b26e2325f67eb977a9fac10
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These are the default ones for the internal CC2520 chip found on the
Quark SE SS devboard. GPIO 11 is used to emulate CS.
Change-Id: Ibc564176f1f77edeb7f25df3567de8c334703795
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
SPI, to control the CC2520 chip, is the only generic feature and thus
the only one configurable through Kconfig. GPIO on the other end depends
a lot on the SoC/Board. Adding a slave select option as well.
Change-Id: I63068fab476ed8d5b26103e4ad20e5be253c9932
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Support for running cc2520 radio found on Quark SE devboard.
Change-Id: Ib0781489e3ebae8569a13c35d3fe6a6d87ac9a3b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This adds very basic support for running on Arduino Due.
Only the nanokernel hello_world has been tested.
Change-Id: I42b83d7f23ff88f709d2d6f2d43c6d29c82b9d32
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Ben Walsh identified a few functions can be removed as they provide
duplicate code except for one small variant (register number). Making
a common function that takes the register position as an input, it is
possible to remove an entire function, saving on code space.
Change-Id: I1850f461ed6d85f42aaf85745e1c2557850cdbad
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
It's basically the same pinmuxer as in CTB with different external
sensors wired to it.
Change-Id: Icea89a72b805d6dd2c5798c3f517c4fb00c819c9
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The production version is slightly different than the internal
development board, so the pin mux description has been updated.
Change-Id: I0235ed9eb480a1fd713843dd1b3b5c7856e7132b
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Shorten the name and remove the vendor prefix. No need to add
vendor to board names.
Change-Id: I68d441121c4034276706da63d7e5420ddf317149
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
