The clock/timer APIs are not application facing APIs, however, similar
to arch_ and a few other APIs they are available to implement drivers
and add support for new hardware and are documented and available to be
used outside of the clock/kernel subsystems.
Remove the leading z_ and provide them as clock_* APIs for someone
writing a new timer driver to use.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There was a bunch of dead historical cruft floating around in the
arch/xtensa tree, left over from older code versions. It's time to do
a cleanup pass. This is entirely refactoring and size optimization,
no behavior changes on any in-tree devices should be present.
Among the more notable changes:
+ xtensa_context.h offered an elaborate API to deal with a stack frame
and context layout that we no longer use.
+ xtensa_rtos.h was entirely dead code
+ xtensa_timer.h was a parallel abstraction layer implementing in the
architecture layer what we're already doing in our timer driver.
+ The architecture thread structs (_callee_saved and _thread_arch)
aren't used by current code, and had dead fields that were removed.
Unfortunately for standards compliance and C++ compatibility it's
not possible to leave an empty struct here, so they have a single
byte field.
+ xtensa_api.h was really just some interrupt management inlines used
by irq.h, so fold that code into the outer header.
+ Remove the stale assembly offsets. This architecture doesn't use
that facility.
All told, more than a thousand lines have been removed. Not bad.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The count register is 64 bits, but we're a 32 bit CPU that can only
read four bytes at a time, so a bit of care is needed to prevent
racing against a wraparound of the low word. Wrap the low read
between two reads of the high word and make sure it didn't change.
Fixes#31599
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Replaces all existing variants of value clamping with the MIN and MAX
macros with the CLAMP macro.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
The HDA wall clock timer is a 64 bit timer with 64 bit compare
registers, but it's being used from a 32 bit CPU. Writing the
comparator piecewise with a 64 bit C assignment will write the low
dword first, opening the possibility that the hardware will see time
go "backwards" and trigger an interrupt incorrectly.
Disable the enable bit while setting the comparator.
Found by inspection. In practice this will be very rare, and spurious
timer interrupts are supposed to be benign anyway (though they can
result in timeout expirations being misaligned to ticks, which might
be surprising to applications). Best to get it right.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Replace various drivers and soc code that use DT_CAVS_ICTL_BASE_ADDR
with DT_REG_ADDR(DT_NODELABEL(cavs0)).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a k_timeout_t type, and use it everywhere that kernel API
functions were accepting a millisecond timeout argument. Instead of
forcing milliseconds everywhere (which are often not integrally
representable as system ticks), do the conversion to ticks at the
point where the timeout is created. This avoids an extra unit
conversion in some application code, and allows us to express the
timeout in units other than milliseconds to achieve greater precision.
The existing K_MSEC() et. al. macros now return initializers for a
k_timeout_t.
The K_NO_WAIT and K_FOREVER constants have now become k_timeout_t
values, which means they cannot be operated on as integers.
Applications which have their own APIs that need to inspect these
vs. user-provided timeouts can now use a K_TIMEOUT_EQ() predicate to
test for equality.
Timer drivers, which receive an integer tick count in ther
z_clock_set_timeout() functions, now use the integer-valued
K_TICKS_FOREVER constant instead of K_FOREVER.
For the initial release, to preserve source compatibility, a
CONFIG_LEGACY_TIMEOUT_API kconfig is provided. When true, the
k_timeout_t will remain a compatible 32 bit value that will work with
any legacy Zephyr application.
Some subsystems present timeout (or timeout-like) values to their own
users as APIs that would re-use the kernel's own constants and
conventions. These will require some minor design work to adapt to
the new scheme (in most cases just using k_timeout_t directly in their
own API), and they have not been changed in this patch, instead
selecting CONFIG_LEGACY_TIMEOUT_API via kconfig. These subsystems
include: CAN Bus, the Microbit display driver, I2S, LoRa modem
drivers, the UART Async API, Video hardware drivers, the console
subsystem, and the network buffer abstraction.
k_sleep() now takes a k_timeout_t argument, with a k_msleep() variant
provided that works identically to the original API.
Most of the changes here are just type/configuration management and
documentation, but there are logic changes in mempool, where a loop
that used a timeout numerically has been reworked using a new
z_timeout_end_calc() predicate. Also in queue.c, a (when POLL was
enabled) a similar loop was needlessly used to try to retry the
k_poll() call after a spurious failure. But k_poll() does not fail
spuriously, so the loop was removed.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The DSP wall clock timer on some Intel SoC is a timer driven
directly by external oscillator and is external to the CPU
core(s). It is not as fast as the internal core clock, but
provides a common and synchronized counter for all CPU cores
(which is useful for SMP).
This uses the RISCV timer as base as it is using 64-bit
counter.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
