Adding port information for uart tx and rx pins in dts, so that it can
be more systematically retrieved in the uart driver.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Convert driver to use DT_INST_ defines. As part of this conversion we
remove the Kconfig options for per GPIO controller enables and instead
get that information from device tree. This means we now disable each
GPIO controller by default in the DTS and have each board dts enable the
GPIO controller ports it needs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked adc_sam_afec driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-uart binding for dma to replace the rxdma and txdma
properties with proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the atmel,sam0-dmac binding under the dma binding dir and add
cell information for channel and trigger source. Update the associated
dtsi files to match these changes.
This is in prep of ATMEL SAM0 SERCOMM devices like UART, I2C, and SPI to
user proper 'dmas' property to specify the dma info to use.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the GCLK, MCLK, and PM clock controllers. Add bindings
and devicetree nodes associated with these clock controllers. Also add
clock references for the SERCOM peripheral set to allow those drivers
(i2c, spi, uart) to utilize this information.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit renames `samd.dtsi` to `samd2x.dtsi` since this DTS header
is specific to the SAM D2x series and its derivatives (e.g. SAM R21).
Note that the SAM D5x series uses a different DTS header file (i.e.
`samd5x.dtsi`) due to the vast differences, and the future SAM D1x will
have to use a separate DTS header to be sensible anyway.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
There was a typo bug in the SRAM ranges property that causes the SRAM
nodes to appear at the wrong addresses.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add pinctl support for the SAM TWI and TWIHS I2C devices. We update
the TWI and TWIHS I2C bindings to have pinctrl-0 bindings that are
expected to have 2 phandles to the TWCK & TWD pinctrl nodes.
The pinctrl nodes will have an 'atmel,pins' property that describes the
GPIO port, pin and periphal configuration for that pin.
We update sam*-pinctrl.dtsi files with all the various pin ctrl
configuration operations supported by the given SoC family. These
files are based on data extracted from the Atmel ASF HAL
(in include/sam<FAMILY>/pio/*.h).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We've had clocks in base.yaml but didn't have clock-names. Add it to
base.yaml with similar functionality to interrupt-names, reg-names, etc.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. We remove the
aliases and use nodelabel instead in the soc_gpio.h to determine the
label for the specific gpio controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
enable the interrupt functionality for sx1509b gpio expander,
when the CONFIG_GPIO_SX1509B_INTERRUPT config is enabled.
The gpio pin used for interrupt should be configured in the
device tree sx1509b node before enabling the interrupt
configuration.
Signed-off-by: Viraaj Somayajula <sviraaj@zedblox.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Mark all the individual PWMs as disabled in dts and enable the one
explicitly used on the mimxrt1064_evk.dts in the board dts file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
DAC (digital to analog converter) peripheral driver with a generic API
suitable for most MCUs (only basic DAC features considered).
Signed-off-by: Martin Jäger <martin@libre.solar>
Add pinctl support for the SAM UART and SAM USART devices. We update
the UART and USART bindings to have pinctrl-0 bindings that are expected
to have 2 phandles to the RX & TX pinctrl nodes.
The pinctrl nodes will have an 'atmel,pins' property that describes the
GPIO port, pin and periphal configuration for that pin.
We add sam*-pinctrl.dtsi files with all the various pin ctrl
configuration operations supported by the given SoC family. These
files are based on data extracted from the Atmel ASF HAL
(in include/sam<FAMILY>/pio/*.h).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The atmel,pins property will be utilized to describe pin mux
configuration. The property will be a phandle-array in which the
phandle points to the given GPIO port the pin is on, the pin number, and
the mux configuration.
This change updates the atmel,sam-gpio binding to support that
phandle-array and updates the associated SoC dtsi files as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add dts support for the headers on Adafruit Feather boards.
This will allow adding FeatherWing boards as shields.
Signed-off-by: Richard Osterloh <richard.osterloh@gmail.com>
Move the majority of the device tree into nxp_lpc55S6x_common.dtsi and
use ranges to handle the different address may for non-secure.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds a GMAC instance to the SAM E5x device tree, along with
the refactoring necessary to specify the SAM E5x-specific components.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The SAM4E GMAC version can use only MII as phy-connection-type. This
update the current default RMII value to MII.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add the following options to GMAC device tree bindings:
- max-frame-size
- max-speed
- phy-connection-type
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit adds a GMAC instance to the SAM 4E device tree.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit fixes the incorrect memory (FLASH and SRAM) size
specification in the device tree and the board test yaml files.
The `qemu_cortex_r5` board (using `fdt-single_arch-zcu102-arm.dtb` FDT)
has 64MiB RAM at the address 0 and 32MiB QSPI flash at 0xc0000000.
QEMU `info mtree`:
0000000000000000-ffffffffffffffff (prio 0, i/o): memory@00000000
0000000000000000-000000000002ffff (prio 0, ram): ddr_bank1_1@0x0
0000000000030000-000000000003ffff (prio 0, ram): ddr_bank1_2@0x30000
0000000000040000-0000000003ffffff (prio 0, ram): ddr_bank1_3@0x40000
00000000c0000000-00000000c1ffffff (prio 0, i/o): lqspi
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Now that all entropy drivers use DTS we can remove HAS_DTS_ENTROPY being
set everywhere as well as Kconfig ENTROPY_NAME since that is now coming
from DT_ENTROPY_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace CONFIG_ENTROPY_NAME with DT_CHOSEN_ZEPHYR_ENTROPY_LABEL. We now
set zephyr,entropy in the chosen node of the device tree to the entropy
device.
This allows us to remove CONFIG_ENTROPY_NAME from dts_fixup.h. Also
remove any other stale ENTROPY related defines in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
dmas and dma-names properties could be used by a wide range
of potential dma client, hence put them in base.yaml, as
optional properties.
Since current stm32-i2s driver implementation only support
dma, set these properties as required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a property to the openisa,rv32m1-gpio binding that relates the GPIO
node to the pinmux PORT node.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Updated the openisa,rv32m1_vega-pinmux binding to require the label
property and updated the rv32m1.dtsi to add label properties for the
pinmux nodes.
Also update gpio_basic_api test to use DT_NODELABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move soc.c code to utilize DT_NODELABEL
instead.
Also rename various node labels to match the SoC docs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as spi. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as usart. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as i2c. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The flexcomm peripheral on lpc socs can be configured into uart, spi,
i2c, or i2s mode. Introduce a shared device tree binding that gets
included by the more specific driver type bindings.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The st,stm32l0-flash-controller did not have a binding, add one for it.
Also made a comment in stm32l0.dtsi that the driver doesn't currently
support this controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The flash at 0 is a cfi-flash and its 2 banks each that are 64M.
Update qemu-virt-a53.dtsi to reflect the proper flash config, however we
comment out the second bank of flash for now because zephyr,flash can
only handle one value in the reg property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Group all the GPIO controllers under a pinctl node so that we have a
container for pinmux configuration data.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds i2c device tree bindings and nodes for the lpc54xxx and lpc55s6x
socs in preparation for adding a new i2c driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Make sure every flash controller has a node label "flash_controller".
This will make it easier to refer to the SoC NVMC node when necessary.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
With the introduction of the new device-tree macros it is now possible
to use the settings for speed and flow-control from the bus node instead
of having the same properties on the esp node itself.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
Define rng nodes for all SoCs featuring the RNG peripheral,
so that the entropy_nrf5 driver can be converted to DTS.
For the network core in nRF5340, align the RNG interrupt priority with
what is used as the default value in (almost) all other DTS nodes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Make the label property required for "arm,cmsdk-gpio" compatible
nodes. Update binding to mark the 'label' property required and updated
associated .dts files to add a 'label' property if it didn't exist.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Currently supported nRF SoCs featuring the second GPIO port (P1) do not
have all 32 pins implemented in that port. Add the "ngpios" property
in gpio1 nodes for these SoCs, so that they don't take the default
value of 32 to indicate the number of available pins but use instead:
- 10 for nRF52833
- 16 for nRF52840
- 16 for nRF5340 (both application and network core)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the STM32L422Xb SoC. Base stm32l422.dtsi on
stm32l412.dtsi to be able to add the crypto device later.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add a YAML, DTS node and driver support to utilize data from devicetree
for register address and driver name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
64 kB of memory is reserved for the inter-processor
communication. this makes sense only if RPMsg is used.
Allow to use this memory for firmware data by default.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
And implement DT_ANY_INST_ON_BUS() in terms of it.
This makes some error messages quite a bit shorter by avoiding
UTIL_LISTIFY(), which has a nasty temper and tends to explode if not
treated gently.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This commit adds a GMAC instance to the SAM V71 device tree, with the
chip revision-specific hardware queue count.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds a GMAC instance to the SAM E70 device tree, with the
chip revision-specific hardware queue count.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The label property of the fixed-partitions child binding was duplicated
with two different values. This is invalid yaml, but went unnoticed by
pyYAML. Removed first entry to preserve value produced by pyYAML
behavior of overwriting duplicates.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Added properties to support the core interrupt controller on the NIOS2
cpu cores and enable that support for the NS16550 UART.
We rename some compatibles so that the cpu core compatibles is unique.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree binding for the NXP Kinetis Low Power Timer (LPTMR)
module. This module can either act as a 16 bit counter or a 16 bit
pulse counter.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
SIM core system clock is being used, but more importantly this will
enable to get the SIM clock controller in use for power management
purposes in MCUX ethernet driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Added device tree nodes and associated headers for
defined uarts on the stm32g0 and stm32g07x 8x parts.
Tested with uart on stm32g071rb disco board with usart3 going to stlink.
Using shell.
Signed-off-by: Kieran Levin <ktl@frame.work>
Use zero-padded 32-bit hex constants for the start address and
length so the fields are easier to compare. Correct the span of
the priority/claim region.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This adds multi-processing support for Intel Apollo Lake ADSP.
Some of the start-up code is borrowed from ESP32.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds the DTS binding for the CAVS Intra-DSP Communication (IDC)
driver for the DSP on Intel SoC.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The shared irq support isn't needed in this driver. We just need to
deal with the fact that some SoCs have only a single interrupt line and
some have three interrupts. We can just ifdef that based on
DT_NUM_IRQS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert the driver to use DT_INST_ defines, update all dependent dts,
soc and board files.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This is joint work with Kumar Gala (see signed-off-by).
Add helper macros which abstract the "true names" of each of the four
types of node identifier we intend to support (e.g. DT_ALIAS(),
DT_INST()).
These can be passed to a new DT_PROP() macro which can be used to read
the value of a devicetree property given a node identifier from one of
these four other macros, and the as-a-c-token name of the property.
Add other accessor macros and tests as well.
Add some convenience APIs for writing device drivers based on instance
numbers as well. Drivers can "#define DT_DRV_COMPAT driver_compatible"
at the top of the file, then utilize these DT_INST_* macros to access
various property defines.
For example, the uart_sifive driver can do:
#define DT_DRV_COMPAT sifive_uart0
Then use DT_INST macros like:
.port = DT_INST_REG_ADDR(0),
.sys_clk_freq = DT_INST_PROP(0, clock_frequency),
For convenience working with specific hardware, also add:
<devicetree/gpio.h>
<devicetree/adc.h>
<devicetree/spi.h>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is useful for devicetree documentation, examples, and tests,
where we need to put something for the vendor but we can't use an
actual piece of hardware for some reason.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The `xlnx,ttcps` binding, despite having the file name of
`xlnx,ttcps.yaml`, had the compatible property of `cdns,ttc`.
While it is true that the Xilinx ZynqMP platform embeds the Cadence
Triple Timer Counter (TTC) IP core, its TTC differs from the original
Cadence core in that it implements 32-bit counters, instead of the
16-bit counters defined in the original; hence, the Xilinx variant is
not compatible with the original Cadence version and should be treated
as a different device.
This commit changes the `xlnx,ttcps.yaml` compatible property to
`xlnx,ttcps` for the above reasons.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This adds support for the Espressif ESP8266 and ESP32 devices to be used
as peripherals on a UART.
There are two main AT command versions that can be selected, 1.7 and
2.0. Since they behave a bit different it is important to select the
one that matches the used in the firmware on your device.
When downloading large amounts of data it is highly recommended to
enable CONFIG_ESP_PASSIVE_TCP and flow control on the UART so that
data is not lost due to UART speed or receive buffer size.
Currently unsupported:
- Changing UDP endpoint with a sendto()
- Bind to a specific local port
- Server socket operations, ie listen() and accept()
Official AT firmware for ESP8266 and ESP32 can be found at:
https://github.com/espressif/esp-at
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
The IIS2MDC is a 3D digital magnetometer ultra-low power sensor
for industrial applications, which can be interfaced through
either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2mdc.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Extended nrf_uart driver to support TX only.
When RX pin is not provided then RX is not started at all. This
allows to achieve low power with logging/console enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add a fixed clock to the qemu-virt-a53.dtsi to match how the musca dts
files work so we get the clock DT info in the same way in the driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add entropy driver based on GECKO TRNG module along with device
tree support for EFM32PG and EFR32MG SOCs.
Signed-off-by: Pooja Karanjekar <pooja.karanjekar@lemonbeat.com>
The ISM330DHCX is a ultra-low power IMU with a 3D digital accelerometer
and 3D digital gyroscope tailored for Industry 4.0 applications, which
can be interfaced through either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/ism330dhcx.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert usb_stm32 driver to use of DT_INST macros.
Since driver is compatible with 3 different dt compatibles and
compatible string is included in DT_INST macros, I've kept the
DT_USB_ compatible agnostic macros based on DT_INST ones, which
allowed to remove fixup definitions.
Use of DT_USB symbols is now limited to usb_dc_stm32.
Additionally, compatible "st,stm32-otgfs" is removed from list
of compatibles for usbotg_hs ips.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On stm32 spi devices, there are 2 main IP variants, with and w/o
fifo. Fifo is not really used today, but still there is some
additional code handling fifo. Today this code is protected under
Kconfig symbol SPI_STM32_HAS_FIFO.
This code carries redundant information vs dedicated compatible
"st,stm32-spi-fifo", which is provided as unique driver compatible
for devices supporting this IP as opposed to use of "st,stm32-spi"
when fifo is not supported.
Having these 2 compatibles defined exclusively is not convenient for
migration to DT_INST as DT_INST macros contain compatible string and
hence it cannot be used to provide common compatible code for devices
defining different compatibles.
Based on these observations, review stm32 spi devices compatible
declarations. Devices supporting fifo will now declare both
compatibles, as proposed by dt spec: "[compatible] property value
consists of a concatenated list of null terminated strings,
from most specific to most general". Hence field will now be:
"st,stm32-spi-fifo", "st,stm32-spi"
This way, fifo enabled stm32 spi devices will generate both:
DT_INST_STM32_SPI_FOO and DT_INST_STM32_SPI_FIFO_FOO
As well as:
DT_COMPAT_ST_STM32_SPI and DT_COMPAT_ST_STM32_SPI_FIFO
So, DT_INST_STM32_SPI_FOO could be used for device initialization.
Also DT_COMPAT_ST_STM32_SPI_FIFO could be used for FIFO handling
code inside driver. Hence use it to replace Kconfig symbol
SPI_STM32_HAS_FIFO.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a property to the nxp,kinetis-gpio binding that related the GPIO
node to the pinmux PORT node.
For the kl25z we add the pinmux nodes as well since they didn't exist.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The IIS2DLPC is a 3D digital accelerometer ultra-low power sensor
for industrial applications, which can be interfaced through either
I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2dlpc.pdf
This driver is based on stmemsc i/f v1.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Enable counter driver support for H7 series. Tested with H743ZI MCU
using samples/drivers/counter/alarm.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Change to code to use the automatically generated DT_INST_*
defines and remove the now unneeded configs and fixups.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Introduction of tachometer device nodes for the Microchip
MEC1501 SOC. In addition, dts bindings for are also introduced.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
LPC55S69 CPU1 definition added.
Dual Core is not enabled!
Definitions related to dual core split of SoC's CPUs.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Add the girq and girq-bit fields to the binding. This allows
encoding GIRQ related information inside device tree.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add girq and girq-bit to encode per device information. This allows the
driver to get any device unique info from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add girq and girq-bit to encode per device information. This allows the
driver to get any device unique info from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The max-value should just be an int and not an array. Change the type
to 'int' in the binding and fixup the driver to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. Replace dts_fixup.h use
for DT_RTC_0_NAME with DT_INST_0_NXP_KINETIS_RTC_LABEL to be
consistent. Also, remove the aliases that had been used for this
driver in various nxp_k*.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines and remove Kconfig per instance
enablement in favor of DT_INST_ define existing. Also, remove the
aliases that had been used for this driver in nxp_rt.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert pms7003 sensor driver to utilize device tree.
DTS would look something like the following for the pms7003:
uart {
pms7003: pms7003 {
status = "okay";
compatible = "plantower,pms7003";
label = "pms7003";
};
};
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert ak8975 sensor driver to utilize device tree.
This also supports the ak8975 embedded in a invensense MPU9150. In such
a case the device tree node should look something like, where the ak8975
is a child of the mpu9150.
mpu9150@68 {
compatible = "invensense,mpu9150";
reg = <0x68>;
label = "mpu9150";
#address-cells = <1>;
#size-cells = <0>;
ak8975@c {
compatible = "asahi-kasei,ak8975";
reg = <0xc>;
label = "ak8975";
};
};
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The driver for STM32's independent watchdog already exists and is
compatible with the stm32g0 SoC. Enable the independent watchdog
for the stm32g0 series for use with this driver.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds Device-Tree instances of the Flash controller
to the SAM3X, SAM4E and SAM4S series. The Flash-Controller
is used to get the unique device identifier.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
On stm32f302/3 series, USB and CAN_1 share same IRQ lines.
To use USB and CAN_1 together, USB IRQ could be remap to other
line numbers, on which there is no conflict.
Remap the USB IRQ lines by default:
-Assign remap number in matching dtsi files
-Perform remap before usb driver init
Additionally, fix compilation issue in usb driver.
Fixes#22343
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
List the details for each type in the order they appear in the summary
of all types. Add the missing 'path' value to the summary.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Fix the following device tree warnings:
unit-address and first reg (0x20000) don't match for iccm@0
unit-address and first reg (0x80010000) don't match for dccm@80000000
Since the em_starterkit_em7d_normal has a different base address for
iccm & dccm, and most of the em_starterkit variants have different sizes
for iccm & dccm. Just define the nodes in the specific
em_starterkit*.dts file and remove them from emsk.dtsi. This removes
the issue reported in the warning.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since there are times that we include a base .dtsi file and change the
reg address we tend to end up with warnings that the reg address and
unit-address don't match. To handle this introduce a simple DT_ADDR(x)
macro that will prepend '0x' to a 'unit-address' style address.
#define DCCM_ADDR 80000000 /* in unit-address format */
dccm0: dccm@DCCM_ADDR {
reg = <DT_ADDR(DCCM_ADDR) 0x1>;
...
};
This allows the dts file to override the value of DCCM_ADDR and than to
have the unit-address of the node and the reg address match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Create an SoC definition for the Audio DSP on Intel Apollolake
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds a simple binding for the Cadence Tensilica Xtensa LX4
CPU. File originally from the LX6 binding.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Update to use new API for GPIO pin configuration and operation. Fix
invalid arithmetic on void pointer. Convert to support devicetree.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update to use new API for GPIO pin configuration and operation. Fix
invalid arithmetic on void pointer. Mark all CC2520 GPIOs as required
in binding.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update the lora/sx1276 driver to the new GPIO API, using configured
active level and the replacement interrupt and active-sensitive set
APIs.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Document and assign write-protect signal as active low, and use the
active-sensitive API to control it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update devicetree sources and bindings, switch to new GPIO API. Use
devicetree property name to identify interrupt signal.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update sample overlays. Add GPIO flags to configuration state.
Refactor to split out setup/handle/process phases. Switch to new API
replacing callback dis/enable with interrupt dis/enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The offset and the number of pins were swapped causing an error when a
64-position left shift was generated to calculate the pin mask.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a config structure for each port and use the devicetree GPIO pin
count to initialize it. Simplify device initialization by using
instance number as only variation point.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Almost all drivers support 32 pins, though some support less.
Eventually this should be specified in every SOC binding, but until
then provide a default so GPIO drivers can be updated to use this.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Since this was converted to the setup/handle/process idiom in master
the conversion is straightforward.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit updates the HMC5883L driver to use the new GPIO API.
Also add a note explicitly describing the active state of the DRDY
pin in the binding file.
Tested on frdm_k64f.
Signed-off-by: Kevin Townsend <kevin@ktownsend.com>
Update sample overlay for missing chip select and to deconflict with
UART TXD. Add GPIO flags to configuration state. Replace callback
enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a sample overlay. Add GPIO flags to configuration state. Replace
callback enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Converts the fxas21002 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on the hexiwear_k64 board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This maps devicetree GPIO phandle arrays from the full controller pin
range to the sub-controllers required by Zephyr's limit of 32 pins per
controller device.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
