Convert older DT_INST_ macro use in stellaris drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The uart_stellaris driver used system clock frequency
as a base for baudrate calculation. This commit corrects
that by obtaining the needed value from DTS.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Per guidelines, all statements should have braces around them. We do not
have a CI check for this, so a few went in unnoticed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
poll_out function was returning the character that was sent. It
happens that it is always constant and the return of this functions is
never tested. Changing it to be a void function.
MISRA-C rule 17.7
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update a couple of labels generated from DTS used directly (not through
dts_fixups) in some serial drivers, to the reflect recent changes made
to the extracting script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Zephyr UART drivers offer very low-level functionality. Oftentimes,
it would be useful to provide higher-level wrappers around UART
device which would offer additional functionality. However, UART
driver irq callback routine receives just a pointer to (low-level)
UART device, and it's not possible to get to a wrapper structure
(without introducing expensive external mapping structures). This
is an indirect reason why the current UARt wrappers - uart_pipe,
console - are instantiated statically just for one underlying UART
device and cannot be reused for multiple devices.
Solve this by allowing to pass an arbitrary user data to irq
callback, set by new uart_irq_callback_user_data_set() function.
Existing uart_irq_callback_set() keeps setting a callback which
will receive pointer to the device.
While public API maintains compatibility, drivers themselves need
to be updated to support arbitrary user data storage/passing (as
legacy uart_irq_callback_set() functionality is now implemented in
terms of it).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Update driver to use DTS-generated #defines for port names,
and not obsolete Kconfig variables.
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
We always have UART_IRQ_FLAGS set to 0, so just call IRQ_CONNECT with a
0 argument for the flags, and remove the UART_IRQ_FLAGS. This is
towards support for using the driver on the TI CC2650. (we add a
comment about that as well).
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Converted Stellaris UART driver over to utilize device tree generated
defines. Added a yaml description for the uart, and converted over the
ti_lm3s6965 SoC & qemu_cortex_m3 board port over to utilize it.
Change-Id: Ie20844eb63d2c68eb59ad4160f7f5b5a35e2943b
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There isn't any reason to export the uart_stellaris_isr function, so
lets make it static and remove the associated header file.
Change-Id: I3a131b584d9d6fb6279a1503512668a71510dd4d
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08f51e2bfd475f6245771c1bd2df7ffc744c48c4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit replaces the nanokernel.h include by kernel.h.
Change-Id: Ib42fbf2d9f77a73c0831f569b3dbbfb342ea2e1d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The UART port base address, IRQ line and clock frequency are static
per SoC, so there is no need to make them configurable in Kconfig.
Change-Id: Ia252958d205e0100d1b92e2a12d4c22411bc94b9
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This patch replaces all occurences of the macro DEV_OK by the actual
value 0 at the driver level. So this patch touch the files under
drivers/, include/ and samples/drivers/.
This patch is part of the effort to transition from DEV_* codes to
errno.h codes.
Change-Id: I69980ecb9755f2fb026de5668ae9c21a4ae62d1e
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
The peripherals utilizing UART were required to register their own
ISR rountines. This means that all those peripherals drivers need
to know which IRQ line is attached to a UART controller, and all
the other config values required to register a ISR. This causes
scalibility issue as every board and peripherals have to define
those values.
Another reason for this patch is to support virtual serial ports.
Virtual serial ports do not have physical interrupt lines to
attach, and thus would not work.
This patch adds a simple callback mechanism, which calls a function
when UART interrupts are triggered. The low level plumbing still needs
to be done by the peripheral drivers, as these drivers may need to
access low level capability of UART to function correctly. This simply
moves the interrupt setup into the UART drivers themselves. By doing
this, the peripheral drivers do not need to know all the config values
to properly setup the interrupts and attaching the ISR. One drawback
is that this adds to the interrupt latency.
Note that this patch breaks backward compatibility in terms of
setting up interrupt for UART controller. How to use UART is still
the same.
This also addresses the following issues:
() UART driver for Atmel SAM3 currently does not support interrupts.
So remove the code from vector table. This will be updated when
there is interrupt support for the driver.
() Corrected some config options for Stellaris UART driver.
This was tested with samples/shell on Arduino 101, and on QEMU
(Cortex-M3 and x86).
Origin: original code
Change-Id: Ib4593d8ccd711f4e97d388c7293205d213be1aec
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is the last step before obsoleting DEVICE_DEFINE() and
DEVICE_INIT_CONFIG_DEFINE().
Change-Id: Ica4257662969048083ab9839872b4b437b8b351b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_DEFINE() so that it fits in the 'device' namespace.
Change-Id: I3af3a39cf9154359b31d22729d0db9f710cd202b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_INIT_CONFIG_DEFINE(), because (a) it was not fitting
in any namespace and (b) it is not used to declare, but rather define a
object.
Change-Id: I1da5822f06b85a9fb024b5b184afd0ccc01012ec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This API is not being used for anything, the interrupts for UART
drivers are all being configured statically. Saves code space as
gc-sections can't tell that these APIs are unused.
Some instances where IRQ/priority information was being saved in
data structures and never used fixed.
Change-Id: If56b4fdc251b80be9094ffcbac6f61e265ac2ffd
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This moves the baud rate and options fields out of the UART driver
config struct and into the driver data struct. This will allow
changing baud rate and options at runtime in the future.
Change-Id: I62ddea2f95e634f2d60eeb9537f960799fc9301f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Since all the necessary bits utilizing UART by index have moved to
use device name instead, the uart_devs[] can finally be removed.
Change-Id: Idbae6b46c0af9eef6c22c59e121e9d6a6b52426a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Since the initialization is now done within driver, there is
no need to expose the port_init() function externally anymore.
After the consumers of port_init() have been updated. It is time
to perform the final step.
Change-Id: Ibe22c6d1dc9525c845acc094fa2066c922439ec3
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
() Renames stellarisUartDrv.c to uart_stellaris.c. This is to follow
the driver naming convention.
() Renames functions stellaris_uart_*() to uart_stellaris_*(),
following driver naming convention.
() Renames CONFIG_STELLARIS_UART* to CONFIG_UART_STELLARIS*
() UART ports initialization is moved into the driver itself.
All the init code in platform config files is removed.
() Adds (many) Kconfig options. These don't have to be defined
in each platform's board.h anymore.
Change-Id: I0eadc3878d69ff24d1637f8df5220fd2f161d24f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
2016-02-05 20:24:56 -05:00
Renamed from drivers/serial/stellarisUartDrv.c (Browse further)
