Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Remove semicolon between instance invocations of DT_FOREACH_IMPL_ and
thus DT_INST_FOREACH. This provides more flexibility to the user. This
requires we fixup in tree users to add semicolon where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make drivers multi-instance wherever possible using DT_INST_FOREACH.
This allows removing DT_HAS_DRV_INST in favor of making drivers just
do the right thing regardless of how many instances there are.
There are a few exceptions:
- SoC drivers which use CMake input files (like i2c_dw.c) or otherwise
would require more time to convert than I have at the moment. For the
sake of expediency, just inline the DT_HAS_DRV_INST expansion for
now in these cases.
- SoC drivers which are explicitly single-instance (like the nRF SAADC
driver). Again for the sake of expediency, drop a BUILD_ASSERT in
those cases to make sure the assumption that all supported SoCs have
at most one available instance is valid, failing fast otherwise.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Use the new devicetree API. Remove per-board enabling of ADC_0 by
setting ADC_0 to default y when the 'adc' node label points at an
enabled node of the expected compatible (depending on SoC).
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The defines should have had a _0 on them, now that we generate the
proper defines, fixup the cases that used that old scheme.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Commit aad21ecb31 introduced an incorrect
pattern of handling ADC sampling requests with invalid parameters in
both nRF ADC drivers. After discarding such request, the drivers do not
release properly the access lock and therefore become unusable.
Unfortunately, this pattern were later on copied in all other ADC
drivers in the source tree.
This commit adds the proper lock releasing in all the affected drivers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Due to a copy-paste mistake, this driver used an incorrect module
name (adc_mcux_adc16) in log messages.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit adds translation layers to make nrfx drivers for the nRF
ADC (nRF51 series) and SAADC (nRF52 series) peripherals accessible via
the Zephyr's API. The SAADC peripheral is accessed using nrfx HAL only
as it turns out that usage of the nrfx driver in this case would be
inconvenient and would unnecessarily complicate the shim.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
