Following other drivers, Kconfig based instances are now entirely
removed. In order to do this change, PWM nodes in board DT files have
been given a pwm{N} label so that both:
- DT API checks such as #if DT_HAS_NODE(DT_NODELABEL(pwmN)) can be
used (N being PWM instance number).
- DT references can be written as pwms = <&pwmN x y>; instead of
pwms = <&{/soc/timers@XXXXXXXX/pwm} x y>;
This approach is also used on the Linux Kernel.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
For auto doc generation purpose, get name value of boards' yaml files
in sync with name provided as board name in .rst file
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The Kconfig PWM_[0-3] sybmols don't have any meaning for kinetis family
SoCs. The driver doesn't utilize them and no sample or test code does
either so we can remove setting them in board Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Kconfig PWM_[0-3] sybmols don't have any meaning for nrf family of
SoCs. The driver doesn't utilize them and no sample or test code does
either so we can remove setting them in board Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the `i2c-0` alias for the Atmel SAM R21 Xplained Pro
board, as required by the I2C test.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the `i2c-0` alias for the Atmel SAM E54 Xplained Pro
board, as required by the I2C test.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit configures the SERCOM2 peripheral to I2C mode for the Atmel
SAM D21 Xplained Pro board.
Note that the SERCOM2 on PA08/PA09 is the I2C peripheral/pin designated
by the board user guide.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit configures the SERCOM2 peripheral to I2C mode for the Atmel
SAM D20 Xplained Pro board.
Note that the SERCOM2 on PA08/PA09 is the I2C peripheral/pin designated
by the board user guide.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Remove the USART 2 definition from the nucleo_g474re board
as it could cause a pin conflict on LPUART1 TX pin (PA2).
The USART2 is not present on this nucleo hardware and then
the g474re board definition is aligned with the nucleo_g431rb.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The OpenOCD JTAG reset causes the SAM E54 SoC to prematurely start code
execution before the SoC is ready, and this causes hard faults when the
MPU is enabled -- causing OpenOCD to hang.
This commit disables the JTAG SRST reset mechanism and falls back to
using the Cortex-M SYSRESETREQ emulation reset mechanism, which does
not have experience this issue.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit enables the ARM memory protection unit for the SAM D54
Xplained Pro board, since `CPU_HAS_ARM_MPU` is now selected by the SoC
Kconfig.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit enables the QEMU icount mode for `mps2_an521`, in order to
decouple the host clock from the emulated guest clock.
This prevents guest timing instability from causing test failures when
the host CPU load is very high.
The icount `shift` value of 7 was empirically chosen to allow the tests
to complete in both realistic and reasonable amount of time.
The following are quick notes on the parameters used:
* -icount shift=7: Execute one instruction every 128ns of virtual time
* -icount align=off: Do not synchronise the host and guest clocks
* -icount sleep=off: Advance virtual time without sleeping/waiting
* -rtc clock=vm: Isolate the guest RTC time from the host
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
native_posix supports for some time now generating a 64bit
binary with the native_posix_64 target, but we never got
to document it.
Add a section describing it, and correct the WSL1
note/warning (also with a link with instructions on how to hack
WSL1 to make it run 32 bit binaries)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Options summary:
-icount shift=5: Execute one instruction every 32ns of virtual time
-icount align=off: Do not synchronise the host and guest clocks
-icount sleep=off: Advance virtual time without sleeping/waiting
-rtc clock=vm: Isolate the guest RTC time from the host
64-bit still has some issues that are being looked at.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
For autogeneration on board pages and indexes, consistency in naming is
required, few board names did not match the images of the boards.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Removing this flag allows to find the spi binary generation tool
in cmake's default paths. This also aligns this CMakeList with
the version currently found in the MEC EVB
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Add board definition for the NXP LPCXpresso55S16 development
board. Only non-secure (ns) access is supported for now.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Kukui has two I2C ports with various peripherals including a battery
charger and a TCPCi-compatible port controller
Enable I2C so that these can be used. No drivers are provided so far.
Also update the GPIO documentation while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove dts_fixup.h files that are not used (empty) or the defines aren't
used anymore and thus can be removed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert linker scripts and arc_mpu_regions.c setup to use new
devicetree.h macros to extract the base address and size of the various
memory regions (DDR, SRAM, FLASH, DCCM, ICCM). We also remove the
scaling up and down since DT_REG_SIZE() returns the value in bytes.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Do not assume in the SoC level device trees that NXP Kinetis FlexTimer
nodes will always be configured as PWM. Instead, configure FlexTimer
nodes for PWM at the board level for NXP Kinetis boards.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add ESP-8266 modules shield. The ESP-01 needs to be loaded with
ESP8266 AT Bin V1.6.2 which is compatible with ESP8266 AT Bin
V1.7.x which is the minimal supported version by ESP WIFI driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The board efr32_radio_brd4250b replaces this removed board. This
commit removes this duplication.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
The HTML documentation generation does not work properly if
we try to put more than one board into same directory. So rename
the directory to reflect this.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit enables the QEMU icount mode for `mps2_an385`, in order to
decouple the host clock from the emulated guest clock.
This prevents guest timing instability from causing test failures when
the host CPU load is very high.
The icount `shift` value of 7 was empirically chosen to allow the tests
to complete in both realistic and reasonable amount of time.
The following are quick notes on the parameters used:
* -icount shift=7: Execute one instruction every 128ns of virtual time
* -icount align=off: Do not synchronise the host and guest clocks
* -icount sleep=off: Advance virtual time without sleeping/waiting
* -rtc clock=vm: Isolate the guest RTC time from the host
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the atom/linker.ld to match how ia32/linker.ld works with regards
to how PHYS_LOAD_ADDR & PHYS_RAM_ADDR are set based on CONFIG_XIP and
from which DT_PHYS_{RAM,LOAD}_ADDR defines. We update the minnowboard
dts and atom.dtsi files to keep in sync with this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
