Commit ceffca2c42 added DTS support for board LEDs and buttons. Remove
redundant LED0_GPIO_PORT, SW0_GPIO_NAME, etc. defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add dts configs for bt-c2h-uart and bt-mon-uart. These are used by
the hci_uart sample and BT_DEBUG_MONITOR.
Signed-off-by: Rubin Gerritsen <Rubin.Gerritsen@nordicsemi.no>
In order to avoid a warning from Sphinx complaining that the
supported_features.rst file is not included in any ToC, rename it to
.txt so that Sphinx understands that this is only a snippet to be
included in other files.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The HiFive1 boards power up using a 32 KiHz low frequency kernel, so
have a cycle rate of 32768 Hz. The board definitions have not been
revisited since the Zephyr default for ticks-per-second increased from
100 to 10000. The timer system on the board does not operate
correctly at 4 cycles per tick, but does at 328 cycles per tick.
To support functional timers while keeping system milliseconds in sync
with clock time set ticks-per-second to 128.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
For consistency with all other boards, make the `buttons` node a child
of the root node, not the `leds` one.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
On LSM6DSO sensor the INT1 pin is used for both generating the drdy
interrupt and for switching to I3C hotjoin mode just after reset if
it is at logical '1' level. If you reset the x_nucleo_shield3 board
the LSM6DSO enter in hot join, as INT1 '1' level is preserved by
the level shifter.
This commit switch to INT2 to generate DRDY interrupt, so that INT1
always remain to logical '0' level.
Fixes: #20933
Signed-off-by: Armando Visconti <armando.visconti@st.com>
mps2_an521 is the default board for ARMv8-M architecture with
support for Security Extension, and CI should test building and
running samples and tests on this board by default. As the focus
is on kernel, userspace, and arm test suites, certain tags are
set to be ignored when testing on this platform.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In Zephyr we have the rule of "do not use stdint defined types",
but unfortunately that leaves us with no properly defined
format specifiers for printing values out.
So cast to stdint types in this expression to actually be able to
do so.
Fixes Coverity CID: 205798
Fixes Coverity CID: 205825
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
When building with support for BLE stack on the nRF5340 APP CPU
(Application MCU), use RPMsg HCI driver by default.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
When building with support for BLE stack, enable the BT_ECC
for the nRF5340 NET CPU (Network MCU).
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
When building with support for BLE stack, enable the Vendor Specific
commands for the nRF5340 APP CPU (Application MCU).
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Provide the mapping from FE310-G002 GPIO pins to the Arduino Uno
headers. Note where pins have pre-assigned functions that may
interfere with use as GPIOs with the default pinmux assignments.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Adds missing items to the list of supported features for all nxp imx rt
boards. These features were already supported, just missing from the
list.
This change increases the number of samples and tests that sanitycheck
selects for these boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Sorts the list of supported features in alphabetical order for all nxp
boards. No features are added or removed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Link to Nordic Semiconductor Infocenter, instead of DocLib
in the documentation for nRF-based Development Kits.
Change Nordic Semi to Nordic Semiconductor in the
DK figure captions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Some people are behind firewalls that prevent them
from doing ssh connections.
Change the default BabbleSim fetching instructions to
be over https which should work for everybody.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
A partition start offsets should be expressed relative to the flash
device base address. For cpunet flash partitions start offsets
were improperly expressed as absolute flash address.
This patch fixes partitions start addresses for nRF5340 cpunet.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Since the nRF5340 DK contains the required DC/DC circuitry,
enable it by default while keeping it configurable. This
reduces power consumption in application core , network
core and high voltage use.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Explicitly configures the rgb led pinmuxes as gpios. Currently the gpio
driver quietly changes the pinmux to gpio mode when configuring a gpio
pin, but this behavior is about to change.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Some board description files failed to note where gpio was supported,
causing tests to be inappropriately filtered. Add the feature where
the gpio_basic_api test would use it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Name convention for nordic USB driver changed
Kconfig files for custom boards have to be udapted accordingly.
Changes affect only name convention change.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This commit adds support for nRF52833 development board.
Changes afffects:
- Introduce files related to board description.
- Add blank documentation file (for future update).
- configuration files for build process.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This commit enables CAN support for the Olimexino STM32 board.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
commit 0df4a53107 changed the behavior of
how openocd commands are passed to openocd. We used to add -c to each
command, now the commands are being added without -c causing an error.
This adds "-c" to all commands instead of just passing a list.
Also fixes#20449.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Provide information required to allow the driver to put the flash chip
into a deep power down mode. This can reduce standby current by as
much as 90%.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The SPI NOR driver requires that the size (in bits) be provided in the
devicetree node. Update the binding to make the property required,
and update all nodes based on the memory chip identified.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The races are believed to be resolved with the patch to
irq_offload(). Allow the MMU to be turned on and enable
it for qemu_x86_64.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We add the functionality that allows the nRF5340 Application
MCU to boot the Network MCU by releasing the RESET line. The
Application MCU may optionally allocate and corfigure resources
that the Network MCU is going to use (currently GPIO and secure
attribution) if running in secure mode. Non-Secure Application
MCU firmware can only issue Network MCU resets.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
When building with support for BLE stack, enable
the BLE Controller module for the nRF5340 DK NRF5340
CPUNET (Network MCU).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Enables the arm v7m mpu on the efr32mg soc and the board
efr32mg_sltb004a.
Tested on hardware with samples/mpu/mpu_test and
tests/kernel/mem_protect
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Specific SW defined BLE LL parameters need to be set
if the user enables it on this platform. As such, conditionally
enable them directly into the defconfig.
INTMUX CH2 and CH3 are not available to be used if BT support
is enabled on Vega, because they are used internally by the
BLE SW LL
Signed-off-by: David Leach <david.leach@nxp.com>
Since the experimental BLE software link layer is enabled on
the VEGABoard, add some information about it, as well as the
limitations.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Having a pin toggle when the code reaches a certain point
is really useful for debugging; the infrastructure is already
in place for Nordic boards, so just build upon and enable the
mechanism on the Vega board as well.
Signed-off-by: David Leach <david.leach@nxp.com>
