Prepare for a day when all boards specify the chip select in the bus
devicetree node by making sure that the devicetree node associated
with arduino_spi uses the standard D10 pin from the arduino header as
the cs-gpios property value.
Also update the arduino tags in the board yaml files.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This adds support for the Atmel SAM E54 Xplained Pro Evaluation Kit.
Only basic functionality has been tested so far.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
By default the firmware is compiled for the EFM32PG12B SoC with the ARM
Cortex-M4F core. When building for efm32pg_stk3402a_jg, The firmware is
compiled for the EFM32JG12B SoC with the ARM Cortex-M3 core.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Most JEDEC NOR flash devices uses not only typical SPI mode
(MISO,MOSI,SCK and CS), but also QSPI mode (IO0,IO1,IO2,IO3,SCK and CS).
QSPI mode uses more data lines and as a result provide higher
throughput. If this were not enough, Nordic chips provide
hardware acceleration for read/write/erase functions, what
gives significant performance boost.
It does a lot of things "behind the scene", i.e when user has written
some data to the flash and would like to read them back, it has to wait
until the flash is ready by reading WIP bit in Status Register.
This driver does it automatically.
Signed-off-by: Kamil Lazowski <Kamil.Lazowski@nordicsemi.no>
Update the hal_nordic module revision, to switch to nrfx 2.1.0.
Because the list of peripherals for nRF5340 has changed as follows:
- SPIM2 has been renamed to SPIM4
- SPIM2-3, SPIS2-3, TWIM2-3, TWIS2-3, and UARTE2-3 have been added
a couple of related corrections needed to be applied in dts and Kconfig
files, plus the spi_nrfx_spim driver has been extended with the support
for SPIM4.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
There is no such thing as CAVS DMA IP block, the DMA IP block found on
CAVS based chips is made with DesignWare one.
This will help to centralize DW based DMA device into one driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The samd20 does not have hardware support for controlling the SS pin.
Declare a cs-gpio to be able to use the SS pin for samd20 xplained pro
board.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Adafruit Feather M0 and Adafruit Trinket M0 boards aren't set up
to use their defined flash partition table to generate the 0x2000
flash offset for code. This should be enabled by default as the
boards ship with a write-protected bootloader and code should be
flashed where it expected by default.
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
Flashing stm32wb SoCs is available since Zephyr SDK-0.11.0.
Enables it on nuclmeo_wb55rg and set it as default as it is
faster in flashing and support doesn't require additional
action (vs pyocd package support).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit introduces the can-primary alias to identify
the primary CAN interface.
This alias is used for all samples and tests, so they don't
need to probe the right interface.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The CONFIG_ prefixes were missing on these.
Found with a work-in-progress scripts/kconfig/lint.py check.
This symbol is defined in kernel/Kconfig.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
I2C interrupts usage should be the preferred way. This commit
enables them by default in the STM32 I2C driver itself.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Same deal as in commit 677f1e6 ("config: Turn pointless/confusing
'menuconfig's into 'config's"), for a newly-introduced stuff.
Also clean up headers to be consistent with recent cleanups.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
During the first real test of my manual by another developer,
I found out that it would be better to update sequence of events.
Also found out misprints, and some actions was not so obvious.
Corrected manual to be more green developers friendly.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Add the user button to the device tree of nucleo_l452re board.
This button is wire to the pin PC13 of STM32L452
Signed-off-by: Julien D'ascenzio <julien.dascenzio@paratronic.fr>
This commit adds initial support for the Silicon Labs EFM32
Giant Gecko GG11 StarterKit.
Features supported for now are NVIC, SysTick, GPIO, Flash,
Counter, I2C, UART and Ethernet. Support for Watchdog and
ADC will follow as soon as their respective PRs are merged.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
Extend `qemu_x86` board configuration with `ieee802154` capability, to
allow it to execute `ieee802154` tests.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
nrf52811_pca10056 board should enable nRF 802.15.4 radio driver
automatically when 802.15.4 subsystem is enabled, as other Nordic
802.15.4-compliant boards do.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Replaced NFFS mentions by LittleFS in all <board>.dts comments
to storage partitions.
Replaced NFFS by LittleFS in a few boards documentation.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Remove link board can, shield was discontinued in
prototype status and will be replaced by a successor.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
...instead of kconfig.
This provides a bit more flexibility in defining driver
instances. Also, since the DTS defines 5 I2C controllers,
the driver code is extended to cover all 5 if the controllers
are enabled.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The I2C controllers on the MEC1501 SoC can be attached to
different I2C output line. For example, the I2C #0 controller
can be used with I2C7 physical lines out of SoC. The output
selection is done by the attribute "port_sel". This renames
the parent I2C nodes on the SoC side to refer to
the controller themselves instead of the output lines to
avoid confusion. The labels of these nodes are also renamed
to reflect the controllers.
On the board level, the DTS labels are overwritten to indicate
the actual output lines.
Aliases are also provided in both SoC and board levels to
provide shortcuts to the DTS nodes.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The SoC, driver, and board support for the CC2650 and CC2650 Sensortag
aren't currently supported and we are removing them as such. If anyone
is interesting in supporting this platform we can easily recovery it
from git.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implement a set of per-cpu trampoline stacks which all
interrupts and exceptions will initially land on, and also
as an intermediate stack for privilege changes as we need
some stack space to swap page tables.
Set up the special trampoline page which contains all the
trampoline stacks, TSS, and GDT. This page needs to be
present in the user page tables or interrupts don't work.
CPU exceptions, with KPTI turned on, are treated as interrupts
and not traps so that we have IRQs locked on exception entry.
Add some additional macros for defining IDT entries.
Add special handling of locore text/rodata sections when
creating user mode page tables on x86-64.
Restore qemu_x86_64 to use KPTI, and remove restrictions on
enabling user mode on x86-64.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
generated_dts_board.h is pretty redundant and confusing as a name. Call
it devicetree.h instead.
dts.h would be another option, but DTS stands for "devicetree source"
and is the source code format, so it's a bit confusing too.
The replacement was done by grepping for 'generated_dts_board' and
'GENERATED_DTS_BOARD'.
Two build diagram and input-output SVG files were updated as well, along
with misc. documentation.
hal_ti, mcuboot, and ci-tools updates are included too, in the west.yml
update.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
HAS_SEGGER_RTT is assigned by various Nordic boards, but assignments
have no effect on promptless symbols. This symbol is enabled through
being select'ed by SOC_SERIES_NRF52X.
Holyiot, nRF52833-PCA10100, nRF52840-PCA10056, and nRF52-PCA10040 only
assign HAS_SEGGER_RTT without assigning USE_SEGGER_RTT. They probably
meant to enable USE_SEGGER_RTT, so do that instead.
Also add a help text to HAS_SEGGER_RTT and a warning re. HAS_SEGGER_RTT
vs. USE_SEGGER_RTT to the documentation.
Flagged by https://github.com/zephyrproject-rtos/zephyr/pull/20742.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
