Reworked i2c_sam_twi driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked uart_sam driver to utilize new DT_INST macros as part of this
rework we also now get pin ctrl/mux configuration information from the
device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
On Atmel SAM family the watchdog peripheral is enabled by default. To
ease maintenance of tests and samples, which typically don't handle
watchdog, disable the watchdog during the boot.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being selected by SOC_SERIES_SAM3X,
SOC_SERIES_SAM4S, and SOC_SERIES_SAME70.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Introduce a standard watchdog alias 'watchdog0' that can be utilized
by sample/test code in the future. This helps remove the need for
CONFIG_WDT_0_NAME in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
With this commit we add the option to use jlink for
flashing and running samples & tests on Arduino Due
using jlink. Bossac remains the default option.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Update configuration of arduino_due board to use a common gpio_sam
driver rather than sam3x specific gpio_atmel_sam3. The gpio_atmel_sam3
driver is going to be deprecated.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit adds 'clock-frequency' property to the cpu nodes.
The clock frequency specified in the added property is used
during platform configuration. Examples:
- The SWO logger uses clock frequency to configure SWO output.
- Plenty of platforms need CPU clock specified for their HAL.
- Most of devices with USB needs information about CPU clock
in order to configure USB clock source.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
This board uses the sam3 gpio driver. gpio_sam was selected by default
causing a conflict and issues when building for this board.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A new role :zephyr_file: is available that renders to a link to the file
or folder in GitHub. Find appropriate references using :file: and
convert to :zephyr_file: to take advantage of its linking capability.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Be consistent in how board docs are named and move all to index.rst.
This will make the URL to the board documentation predictable and easier
to remember.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The i2c_atmel_sam3 driver was deprecated at release 1.9, this commit
removes it. Also pinmux_dev_atmel_sam3x driver is removed.
i2c_atmel_sam3 was the last one which depended on it.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Adding watchdog driver for sam SoC. The current implemntation just
diables the watchdog on device boot.
This PR adds the following support for SAM3X, SAM4S and SAME70
1. Activate processor reset
2. Activate all reset
3. Generate interrupt on watchdog timer expiration.
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The old GCC ARM Embedded website on launchpad
(https://launchpad.net/gcc-arm-embedded) has been superseeded by the new
GNU Arm Embedded one
(https://developer.arm.com/open-source/gnu-toolchain/gnu-rm).
This also means a change of name from "GCC" to "GNU". Reflect this in
the enviroment variables so that the proper term is used henceforth.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update the link to SAM3X8E datasheet and
update the minicom command to use sudo as
accessing the serial port requires root permission
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
Both variables were used (with the same value) interchangeably
throughout CMake files and per the discussion in GH issue,
ZEPHYR_BASE is preferred.
Also add a comment with explanation of one vs. the other.
Tested by building hello_world for several boards ensuring no errors.
Fixes#7173.
Signed-off-by: Alex Tereschenko <alext.mkrs@gmail.com>
In preparation for introducing a warning.
Unquoted string defaults work through a quirk of Kconfig (undefined
symbols get their name as their string value), but look confusing. It's
done inconsistently now too.
Suggested by Kumar Gala.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Underscore ('_') isn't a valid char for alias names based on the device
tree spec. Newer dtc compilers flag this as a warning so lets clean it
up. Replaced '_' with '-' to keep things simple.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/atmel_sam/<BAR>/dts.fixup so we remove duplication in the
boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implements interrupt driven UART for the serial driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Instead of accessing the environment variable ZEPHYR_BASE every time we
require accessing the source code root, use an intermediate variable
that has OS path separators correctly set to '/' to avoid issues on
Windows.
Note: This removes the ZEPHYR_SOURCE_DIR CMake variable. External
applications using that will need to change to use the new ZEPHYR_BASE
variable.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The various runners (flash/debug scripts) use environment variables to
take arguments. This is legacy behavior which is not desirable.
Use command line arguments instead.
Note: this leaves more general environment variables with publicly
documented behavior in place for now, for compatibility, e.g.:
ZEPHYR_FLASH_OVER_DFU, OPENSDA_FW, ESP_IDF_PATH, PYOCD_DAPARG
For example, when using dfu-util to flash arduino_101, instead of
setting DFUUTIL_PID, DFUUTIL_ALT, and DFUUTIL_IMG environment
variables, have the script invocation look like this:
python3 .../zephyr_flash_debug.py dfu-util flash \
[common arguments omitted] \
--pid=8087:0aba --alt=x86_app \
--img=.../build/zephyr/zephyr.bin
Make similar changes for other runners (openocd, etc.) and
targets (debug, debugserver).
To implement this in the scripts:
- have the individual scripts/support/runner/some-runner.py files
register their own command line arguments
- teach them to construct instances from arguments, not the
environment
- have zephyr_flash_debug.py request runners to register command
line argument parsers, and handle arguments
In the build system:
- add a new board_runner_args() extension function that board.cmake
files can use to add to the zephyr_flash_debug.py command line
- adjust cmake/flash/CMakeLists.txt to invoke with arguments
- add new helper include files for each runner (like
boards/common/dfu-util.board.cmake, etc.), which add default
options as needed and then add on overrides from
board_runner_args() calls
- update board.cmake files to use the new includes and extension
This implied some tweaking when using openocd to make the CMake string
escaping and unescaping work properly.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
The Python-based runners have replaced the old shell scripts. Refactor
the build system accordingly:
- FLASH_SCRIPT is now BOARD_FLASH_RUNNER
- DEBUG_SCRIPT is now BOARD_DEBUG_RUNNER
The values, rather than being the names of files, are now the names of
runners in scripts/support/runner. They are still short, descriptive
names like "openocd", "jlink", "em-starterkit", etc.
Adjust the zephyr_flash_debug.py call and runner internals
accordingly. Have each runner class report a name and the commands it
can handle. This lets us move some boilerplate from each do_run()
method into the common run() routine, and enables further improvements
in future patches.
The handles_command() method is temporary, and will be replaced by a
more general mechanism for describing runner capabilities in a
subsequent patch. The initial use case for extending this is to add
device tree awareness to the runners.
To try to avoid user confusion, abort the configuration if an
xxx_SCRIPT is defined.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the dts fixup files into the board dir so that board ports can be
more standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Added I2C bus (TWI) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Arduino Due board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add board metadata to be consumed by the sanitycheck script to provide
better matching with testcases and to test based on features declated in
the board files.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Atmel SAM3X series has been recently converted to use ASF
and should now use common SAM family drivers. The atmel_sam3
serial driver will be removed in the future.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
