Increase the L2CAP buffer count, for the media control shell to work.
(The buffer count was set to an even higher value in the
topic-le-audio branch, but that setting was not upmerged.)
Signed-off-by: Asbjørn Sæbø <asbjorn.sabo@nordicsemi.no>
The le-audio host shell enables extended advertising. Therefore, for
the shell to be usable, extended and periodic advertising must also be
enabled for the controller.
The controller configuration are added to board-specific files for the
time being, as the advertising features are still experimental
upstream.
Signed-off-by: Asbjørn Sæbø <asbjorn.sabo@nordicsemi.no>
Update the configuration file to use BT_FILTER_ACCEPT_LIST
instead of the deprecated BT_WHITELIST.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The define for PDU_AC_LL_SIZE_EXTRA was removed in main, but not in
the topic-branch. The merge of topic/branch erroneously reintroduced
this define, so it needs to be removed
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
HCI tests HCI/DSU/BV-05-C and HCI/GEV/BV-01-C fail when
compiling with debug optimisations turned on.
Therefor revert to not compiling with debug optimisations.
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
Update the macro prototype to explicitly require the length of the
desired user data. Update all in-tree usage of this macro.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Adds preprocessor ifdefs to reconfigure() in L2CAP tester application
depending on the KConfig option CONFIG_BT_L2CAP_ECRED
Fixes issue #40456
Signed-off-by: Johan Lundin <johan.lundin@nordicsemi.no>
For consistency we run the gatt and gap tests also with the new
LLCP. The test lists for legacy and new LLCP are identical
and therefor no separate test lists have been introduced
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
Rename the mockup file from ull_periph.c into ull_peripheral.c
so that it has the same name as its equivalent in the BT
controller
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
If IUT is acting as a central device and peer lost bond we need
to re-pair to restore bond. PTS is not sending any WID for this
so bonding needs to be initiated implicitly by IUT.
This was affecting GAP/SEC/AUT/BV-25-C qualification test case.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Use the host BIG Sync APIs to test the BIG Sync establish
and Sync Terminate implementation in the controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix the bsim test_iso application so as to sync with periodic
adveritising. Increase the timeout so that the test passes.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Construction of BIGInfo with mandatory parameters and
placing it in the ACAD of Periodic Advertising PDU.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added tests to check Broadcast ISO allocations are released
on terminate, and new Broadcast ISO create is successful.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Remove option CONFIG_USB_UART_CONSOLE where it has no influence
or enable CONFIG_SHELL_BACKEND_SERIAL_CHECK_DTR without taking
a detour through CONFIG_USB_UART_CONSOLE.
Check the compatibility of chosen property instead
of usage of CONFIG_USB_UART_CONSOLE option.
Align how to wait for the readiness of CDC ACM UART.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Pushes all work done in the topic-ble-llcp branch into main branch
This is a refactoring of the LL control procedures; the refactored
control procedures are hidden behind a KConfig option and
per default disabled
Goal of the refactoring:
close issue Link Layer Control Procedure overhaul #15256
make it easier to add/update control procedures
Refactoring consists in principal of writing explicit state machines
for the control procedures.
To reduce the risk of regression errors unit-tests have been added
Following control procedures are implemented:
Connection update procedure
Channel map update procedure
Encryption procedure
Feature exchange procedure
Version exchange procedure
ACL termination procedure
Connection parameters request procedure
LE Ping procedure
Data Length Update procedure
PHY update procedure
Min. nr. Of channels used procedure
Constant Tone extension request procedure
This is a joined work by the people listed in the signed-off-by
list (in alphabetical order)
Signed-off-by: Andries Kruithof Andries.Kruithof@nordicsemi.no
Signed-off-by: Erik Brockhoff erbr@oticon.com
Signed-off-by: Piotr Pryga piotr.pryga@nordicsemi.no
Signed-off-by: Szymon Janc szymon.janc@codecoup.pl
Signed-off-by: Thomas Ebert Hansen thoh@oticon.com
Signed-off-by: Tommie Skriver tosk@demant.com
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
Enable ISO (unicast and broadcast) for the BT shell.
This allows users to use the ISO features (if supported by
the controller) in the shell.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Adds support for reading multiple variable length characteristics.
Previously read_multiple() always set the variable flag to false.
This is used by GATT/CL/GAT/BV-03-C.
Signed-off-by: Herman Berget <herman.berget@nordicsemi.no>
A FEM in this case is an external Front-End Module. This is basically
a range booster with some extra amplification in the TX and RX paths.
This feature is supported for the Nordic open source controller. See
the changes to the ubx_bmd345eval_nrf52840 board for a quick summary
of what you have to do to take advantage of this.
(This patch doesn't actually remove the feature in the openisa HAL,
though, because that never implemented the required GPIO handling
routines.)
We are using the 'fem' property previously added to the
nordic,nrf-radio's devicetree binding, which points to the FEM that is
in use. If you have this property and the node it points to is
enabled, the controller subsystem respects it. Otherwise, FEM support
is disabled.
This obsoletes the following Kconfig options, which are now unused:
- CONFIG_BT_CTLR_GPIO_PA
- CONFIG_BT_CTLR_GPIO_PA_PIN
- CONFIG_BT_CTLR_GPIO_PA_POL_INV
- CONFIG_BT_CTLR_GPIO_PA_OFFSET
- CONFIG_BT_CTLR_GPIO_LNA
- CONFIG_BT_CTLR_GPIO_LNA_PIN
- CONFIG_BT_CTLR_GPIO_LNA_POL_INV
- CONFIG_BT_CTLR_GPIO_LNA_OFFSET
- CONFIG_BT_CTLR_FEM_NRF21540
- CONFIG_BT_CTLR_GPIO_PDN_PIN
- CONFIG_BT_CTLR_GPIO_PDN_POL_INV
- CONFIG_BT_CTLR_GPIO_CSN_PIN
- CONFIG_BT_CTLR_GPIO_CSN_POL_INV
- CONFIG_BT_CTLR_GPIO_PDN_CSN_OFFSET
The PA and LNA pins are now specified via fem-specific devicetree
properties in the FEM node:
- The "generic" PA/LNA case is handled with the ctx-gpios and
crx-gpios properties of the generic-fem-two-ctrl-pins compatible,
respectively.
- If the fem is an nRF21540, use the tx-en-gpios and rx-en-gpios
properties instead (and also respectively). This allows us to specify
FEM properties in a way that makes sense for the hardware datasheet,
while still handling them in a uniform way within the controller.
We support this in the nRF5 HAL with a new radio_nrf5_fem.h
sub-header, which pulls in radio_nrf5_fem_generic.h or
radio_nrf5_fem_nrf21540.h depending on the fem node's compatible, if
one is defined. These in turn let us replace the implementation
routines in radio.c with DT equivalents.
Keep in-tree users and devicetree binding documentation up to date.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Recently there was added ADI support to periodic advertising.
There was missing implementation of ADI for periodic advertising
chained PDUs and direction finding. Also unit tests for periodic
advertising chains required update to handle ADI field.
The commit provides missing implementation.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This commit add the BabbleSim tests for the media control client, the
media control service and the media proxy. This is a part of the
upmerge of the le-audio media control files.
These tests have been developed and maintained along with the media
control functionality. The tests are believed to cover all
implemented media control functionality.
The commit is a pure copy of the files and content in the
topic-le-audio branch, with the exception that some include paths have
been modified to correspond to new locations of files and that the
tests have been guarded with ifdefs.
Signed-off-by: Asbjørn Sæbø <asbjorn.sabo@nordicsemi.no>
test guards
Add entries for media control builds to testcase list. This is a part
of the upmerge of media control from the topic-le-audio branch.
Signed-off-by: Asbjørn Sæbø <asbjorn.sabo@nordicsemi.no>
Upmerge of the project settings for media control from the
topic-le-audio branch.
Signed-off-by: Asbjørn Sæbø <asbjorn.sabo@nordicsemi.no>
audio.conf changes
This allows to do directed advertising with peer address set to RPA.
To do this according to specification IUT must first read Central
Address Resolution characteristic to check if peer supports it.
This is affecting GAP/CONN/DCON/BV-05-C qualification test.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Move the header file csis.h from the internal location to
the public include directory. This file is supposed to provide
the public API for CSIS and the CSIS client, but is not fully
complete yet.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Adds the coordinated set identification service (CSIS) client.
This is still a work in progress and thus there are no public
API for it yet, and some code changes will still be needed.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Adds the coordinated set identification service (CSIS) server.
This is still a work in progress and thus there are no public
API for it yet, and some code changes will still be needed.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The mesh shell module owns the composition data for the shell
application, which makes it impossible to use it outside of the
application itself. To support the shell as a generic debugging
component that can be added to any application, we have moved the
composition data out of shell.c, and into the application.
Signed-off-by: Ingar Kulbrandstad <ingar.kulbrandstad@nordicsemi.no>
As the already existing macro K_MEM_SLAB_DEFINE results in
two variable definitions, the preceding static modifier leads to
a seemingly working solution, though linkage conflicts will occur
when the same memory slab name is used across multiple modules.
The new K_MEM_SLAB_DEFINE_STATIC macro duplicates the functionality of
K_MEM_SLAB_DEFINE with the difference that the static keywords are
internally prepended before both variable definitions.
The implementation has been tested on my Zephyr project (the build
issue faded out). The documentation has been updated altogether
with all incorrect occurences of static K_MEM_SLAB_DEFINE.
Signed-off-by: Pavel Hübner <pavel.hubner@hardwario.com>
Add iterations of connections and disconnections to
Babblesim test of Bluetooth Low Energy Central role
functionality by scanning for other devices and establishing
connection to upto 62 peripherals with a strong enough
signal.
Enable Auto PHY Update and Auto Data Length Update procedure
in the central_multilink sample.
Enable Auto PHY Update and Auto Data Length Update procedure
in the peripheral_identity sample. Fixed issues related to
rotation of identities after maximum number of connection
iterations are repeated.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add mixed Legacy Directed Advertising and Extended Advertising
test in the babblesim coverage for Extended Advertising
feature.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
