`setsockopt` is enabled by `CONFIG_POSIX_API`, use
`zsock_setsockopt` instead, otherwise there will be a
compilation error if `CONFIG_NET_SOCKETS_SOCKOPT_TLS` is
enabled.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Check if the interface is down before joining IPv4 mDNS multicast
group. This avoids warning later when the network packet cannot be sent.
Fixes#71121
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This API is not widely used and it is actually broken since device
runtime power management is not checking it when suspending and
resuming.
On top of that, this API is very close to pm_device_busy* API,
close enough to consolidate in only one API.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Commit e99b5228a1 changed the default
networking behavior on qemu platforms, as the SLIP_TAP driver no longer
selected Ethernet L2. In results, qemu platforms in default
configuration had no network interface to work with.
Fix this, by restoring select for NET_L2_ETHERNET, but this time in
NET_SLIP_TAP. The difference is that SLIP_TAP is a generic driver
config, which could be enabled on any platform, so not changing the
behavior here, while NET_SLIP_TAP is a config dedicated for qemu only,
so it's reasonable to enable all that's needed to get SLIP to work with
qemu by default.
As there were circular Kconfig dependencies, move the respective qemu
configs outside of NET_RAW_MODE if block (as this caused the circular
dependency with ETH_DRIVER_RAW_MODE). Also, remove dependency to
NET_L2_BT, as it made little sense there, and also caused dependency
problems.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
There is no limitations for dwell time. Just add
valid condition for positive value. So , it's better
to remove those constraints.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
The bt_debug_dump_recv_state did not care if the receive
state being dumped to log was active or not, and if it was
not actice, then it may just contain random data.
Added a check to see if it was active.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Running out of connection contexts is most likely due to app
misconfiguration, therefore it's useful to get an explicit information
that context allocation failed.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The cap_initiator unicast_stop command will now stop
all streams by default, without supplying the "all" argument.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Some part of the descriptions were wrong. Also, the description of
`BT_BUF_ACL_RX_SIZE` was too verbose and no longer needed with the
updated L2CAP documentation.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
The buffers for the PBP advertising data as well as the
buffers for the BASE periodic advertising data were
not cleared, so calling the functions multiple times
would simply append the data rather than just setting
the new data.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
There are devices that will send empty SDUs instead of
empty PDUs, and while that should be harmless, it is nice
to know what is going on, and we may want to deal with
empty SDUs and empty PDUs differently.
This also modifies the state for TS and PSN to only be
applied for valid ISO packets.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
It is a common occurance that a specific type is not
found in the codec configuration, and the main way of
knowing that is by calling the function.
The debug log does not help debug anything (as it does also
return a specific error code), but rather just clutters up
the log if enabled.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
When returning an error code directly to an application
in the API, it should not log as a warning or error.
The lack of PAC records is also reported directly to the
application, and is not an error (in fact it is valid not to have
e.g. sink or source pacs).
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add printing of the broadcast ID and whether an existing PA
sync was found in the bap_broadcast_assistant_recv_state_cb
function.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The bap_broadcast_assistant mod_src command can now take "unknown"
as a value to supply BT_BAP_PA_INTERVAL_UNKNOWN to the scan
delegator.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The documentation for the command
bap_broadcast_assistant broadcast_code
was incorrect and has been fixed.
Additionally, and example of the command has been added
in the shell documentation.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
When a PA is synced via PAST, the receive state does not
have a PA sync object, and the address and SID must be
used.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The audio configuration 5 is defined to have 2 sink channels
per stream and 1 source channel per stream.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
If pa_sync_past returns 0 then that means we are ready to
sync to past, and the BT_BAP_PA_STATE_INFO_REQ state should be set.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Some toolchains cannot create shared objects for Xtensa, with them we
have to use relocatable objects. Add support for them to llext.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Correct various small edge-case behaviors that have been accidentally
introduced in the http_client.
- http_client_req no longer incorrectly returns -ETIMEDOUT on NULL HTTP
resonse. -ETIMEDOUT is now only returned when the underlying TLS
socket times out.
- http_client_req now returns -ECONRESET upon incomplete (but non-NULL)
HTTP response. The request callback is no longer called in this case
(as with any other error state).
- http_wait_data has been refactored slightly to increase clarity.
Signed-off-by: Georges Oates_Larsen <georges.larsen@nordicsemi.no>
If the packet cloning fails (can easily happen when working with
loopback interface and when having low net_buf count), then
print a warning to the user. Error could also be possible but
as the situation might correct itself in this case, the warning
should be enough.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Adds the CAP Commander Change Microphone Mute procedure.
This procedure changes the microphone mute state on one or more
CAP Acceptors.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
If we fail to join all nodes or solicit node multicast groups
when the interface is down, then there is no need to print an
error message. The groups are automatically re-joined when the
interface comes up.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
remove unnecessary condition for CONFIG_HAWKBIT_POLL_INTERVAL,
changes poll_sleep to be in seconds,
change type of sleep_time in hawkbit_update_sleep(), so the return
value of hawkbit_time2sec() is interpreted correctly.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
In addition to flushing the dcache, to ensure that the new code is
actually read by the CPU when loading an extension, the icache must
be invalidated as well.
Without this, some tests are failing in hardware because the CPU is
executing stale code from its instruction cache.
Fixes#70906 on arduino_giga_r1/stm32h747xx/m7.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Resolved a data race in shell.c by copying the user-provided
prompt-string into a private buffer within the shell, ensuring
proper synchronization with the shell-thread.
Fixes: #64972
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@verkada.com>
If user created the capture device using the API and not via
the shell, then the device name was not set. Use the default
capture device in this case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The event NET_EVENT_CAPTURE_STARTED is generated when the
capture is enabled, and NET_EVENT_CAPTURE_STOPPED when capture
is disabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The net_capture_pkt() does not return information what happened
to the net_pkt because the packet was always cloned. With cooked
capture we can avoid the cloning in which case we need to know
the capture status in order to unref the packet if needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add support for capturing arbitrary data via the cooked mode (sll)
capture API. The actual packet capture is done using net_capture_data()
function, the packet capture infrastructure does not need any changes.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Allow user to create a kitchen sink pseudo a.k.a any network
interface that one is only able to write to. This might seem
unnecessary, but it is possible to attach virtual network
interfaces on top of this pseudo interface. These virtual
interfaces could then process the data for example for
packet capture purposes.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
For debugging purposes it would be nice to see the verdict
printed as a string instead of number.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add a recv callback to dummy API. After this it is possible to
receive data by a dummy network interface. This is only useful
if one attaches a virtual interface on top of the dummy one.
One such example is the cooked mode capture interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Change 'Hawkbit' and 'hawkbit' to 'hawkBit' wherever
makes sense, and a bit of touch ups here and there.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
This commit fixes an issue where due to inverted logic (static function
returned 0 on success but the caller expected true/false) the MLDv2
reports were silently dropped.
Signed-off-by: Konrad Derda <konrad.derda@nordicsemi.no>
Added a check for checking duplication when adding a source in the
broadcast assistant, as per requirement in BAP 6.5.4. It is not
permitted to add a source such that a combination of broadcast_id,
adv_sid and address type would result in same triple of values.
Added a recv_state struct to cache these values when read, and moved
past_avail and srd_ids into this as well.
Signed-off-by: Fredrik Danebjer <frdn@demant.com>
Deprecate CONFIG_NET_TCP_ACK_TIMEOUT as it is redundant with the
combination of CONFIG_NET_TCP_INIT_RETRANSMISSION_TIMEOUT and
CONFIG_NET_TCP_RETRY_COUNT. The total retransmission timeout (i. e.
waiting for ACK) should depend on the individual retransmission timeout
and retry count, having separate config is simply ambiguous and
confusing for users.
Moreover, the config was currently only used during TCP handshake, and
for that purpose we could use the very same timeout that is used for the
FIN timeout. Therefore, repurpose the fin_timeout_ms to be a generic,
maximum timeout at the TCP stack.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add hostname changed printout to event monitor. As the name
says, it is generated when the hostname of the device changes.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Starting with b1d24e425c (net: lwm2m:
device object: optionally store error list in settings), it was no
longer possible to build the code with coverage enabled when the
settings subsystem was disabled.
The build would fail with an error like this:
> subsys/net/lib/lwm2m/lwm2m_obj_device.c:262: undefined reference to
> `settings_name_steq'
This fixes#70923.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
