Fix Data Length Update transmit and receive time calculation
on PHY update procedure completion.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix host resolving the peer identity address in enhanced connection
complete event when the resolving list in the controller is full and
resolution is done in the host.
Move the handling from legacy connection complete into enhanced
connection complete event so that it is done for both connection
complete events.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Implements several changes to the transport layer segmented tx to
improve group message performance:
- Moves retransmit counter to tx context instead of per packet. As every
unacked packet is sent every retransmit, the retransmit counters would
be the same in each segment. This makes it easier to control progress.
- Delays the scheduling of the retransmit until the completion of the
last segment by adding a seg_pending counter. This is essentially the
same as the old behavior, except that the old behavior might retrigger
the sending before all segments are finished if the advertising is
slow.
- Allows the group transmits to stop as soon as all retransmits have
been exhausted, instead of timing out waiting for acks that won't
come. This allows group tx to finish without error.
- Fixes a bug where a failed TX would block IV update.
- Cancels any pending transmissions of acked segments.
- Reduces log level for several common group tx scenarios that aren't
erronous.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
When available, the shell will use the CDB when configuring. This
replaces the default key for configuration and self-provisioning,
ensuring that there aren't multiple key values for the same indexes.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
If the application has used bt_le_oob_get_local to retrieve the OOB
RPA address and OOB authentication information the central role should
use this RPA address for the next RPA timeout period.
The central role always refreshes the RPA address for the initiator,
this will make the OOB information not usable as the peer cannot
recognize the central role since the RPA address is changed.
Check if the initiator can use the address for the duration of the of
remaining RPA period.
Fix central role using the advertiser identity when setting the private
address. The central role should only use the default identity.
Regressions from:
fbe3285bfa
and
4876a8f39a
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix possible NULL dereference in BT_DBG statement when
bt_mesh_friend_get is called before a successful cfg_srv init
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix conditional compilation error when enabling
BT_CTLR_FAST_ENC for central only application builds.
Also added additional compilation to code exclusive to
central or peripheral role.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When building the tests/bluetooth/shell application without
the BT_CENTRAL feature, compilation fails:
subsys/bluetooth/shell/bt.c:1642: undefined reference to
`bt_conn_create_auto_le'
Signed-off-by: Vinayak Kariappa Chettimada <vinayak.kariappa@gmail.com>
Fix problem of not checking if the remote device key is actually our
own. This bug was intruduced in
46a95f12ad and causes failure of models
that use app_idx BT_MESH_KEY_DEV_REMOTE. Since this is used by cfg_cli,
it was not possible to do self-configuration.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
Add Kconfig option to support building the controller
optimized for speed.
Fixes#21601.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix local initiated Data Length Update procedure from being
stalled when a remote initiates a procedure with instant.
Fixes#23069.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix Tx pool from being corrupted when rough central device
uses invalid packet sequence numbers, causing NULL pointer
to be released into free data Tx pool.
Fixes#22968.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If the client is change-unware and disconnects the spec requires that
the stack still sends the error out of sync for the next request:
'The ATT_ERROR_RSP PDU is sent only once after the client becomes
change-unaware, unless the client _disconnects_ or the database changes
again before the client becomes change-aware in which case the
ATT_ERROR_RSP PDU shall be sent again'
Fixes#23110
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Resend transport segments for groups on the advertiser interface, even
if a connected proxy node holds the group.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Update help text of `bt init` command which says address could be
provided. This feature was removed by:
d22b7c9f2d
As a replacement the `bt id-create` command can be used instead.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When a must-expire ticker callback is executed, it is important not to
call the LLCP state machine, as the lazy state is unavailable. The code
must rely on the next proper event to call ull_conn_llcp with an updated
non-zero lazy count.
Signed-off-by: Morten Priess <mtpr@oticon.com>
Fix EBQ tests for the Max Tx Time and Max Rx Time parameter.
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
Bluetooth: controller: split: fixed for endianness
Added conversion to correct endianness
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
Fix local initiated Data Length Update procedure from being
stalled when a remote initiates a procedure with instant.
Fixes#23069.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix issue where a new connection with the same peer would use the CCC
from from first connection, despite different local identity.
Since there is no CCC for the new connection yet this caused the
application to think that CCC was enabled but the remote device had not
yet subscribed.
Fix this issue by making the id as an input to the peer address check
function. This will force us to make the check every time. This commit
might also fix similar issues not yes discovered as the ID check was
missing in a few other places as well.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Rename the acl buf context id to index since to avoid confusing it with
the conn object ID parameter. Especially the bt_conn_lookup_id function
was creating confusion.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix ticker resolve collision implementation for incorrect
ticks accumulation and the calculation of next period.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix a race condition in radio abort requested by flash
driver. It is possible that during abort function execution,
PPI setup to start radio fires. Hence, check explicitly in
cleanup function for radio being in use and disable it.
Fixes#22945.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Use the old ticker compatibility mode implementation as
default for nRF5x Series SoCs.
Fixes#22926.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Avoid the HCI-USB race condition where HCI data and HCI events can be
re-ordered, and pairing information appears to be sent unencrypted.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix to remove assertion failure check on detecting invalid
packet sequence used by peer central and that no non-empty
packet was transmitted.
Fixes#22967.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix issue where an invalid (all zeroes) hash was written to settings
storage on reset. This caused the old value to written to zeroes, before
being written back to it's original value again immediately after.
This causes excessive flash wear.
This happens because the check if (k_delayed_work_remaining) returns the
amount of time until the work will execute. When that time has run out
the time is zero, but the work has not yet been executed.
We then write the invalid hash to flash, and then once the work-item
executes it will write the correct value.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
- avoid spourious radio interrupts by fixing ISR set,
waiting for idle, command configuration
- adjust counter to account for missing increment
- change preemption instant to avoid missing the deadline in LLL
- decrese EVENT_JITTER_US and
EVENT_TICKER_RES_MARGIN_US (same as Nordic)
Continuous scanning and connections are working fine now.
Signed-off-by: George Stefan <george.stefan@nxp.com>
Created unit tests for the encryption and decryption functions.
Tested with the peripheral and with central_hr samples.
Due to latency of CAUv3 when used as CCM inline accelerator
only one of the PDU can be encrypted/decrypted within an
bilateral exchange M->S + S->M in a connection event.
If the RXed PDU is encrypted, the TXed PDU must be empty
with More Data if there is data in the LLL queue.
The TXed PDU will be encrypted when an empty PDU is RXed.
Signed-off-by: Cristi Caciuloiu <cristian.caciuloiu@nxp.com>
Fix regression due to addition of conditional compilations
while porting the privacy feature from legacy to split
controller.
Fixes#22801.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Backport of https://github.com/apache/mynewt-nimble/pull/724
Mesh spec 1.0.1 changes proxy disabling behavior to only affect the
relaying from proxy nodes. Previously, disabling proxy would shut down
all proxy and node activity.
Tweaks from the original commit:
- Removed redundant call to bt_mesh_adv_update() in gatt_proxy_set()
- Removed invalid ref to 4.2.11.1 in node_identity_set()
---
According to Mesh Profile Spec 1.0.1, Section 4.2.11:
"If the Proxy feature is disabled, a GATT client device can connect
over GATT to that node for configuration and control. Messages from
the GATT bearer are not relayed to the advertising bearer."
Moreover some notes have been removed from the spec compared to
version 1.0:
Mesh Profile Spec 1.0, Section 4.2.11:
"Upon transition from GATT Proxy state 0x01 to GATT Proxy state 0x00
the GATT Bearer Server shall disconnect all GATT Bearer Clients."
"The Configuration Client should turn off the Proxy state as the last
step in the configuration process."
Mesh Profile Spec 1.0, Section 4.2.11.1:
"When the GATT Proxy state is set to 0x00, the Node Identity state
for all subnets shall be set to 0x00 and shall not be changed."
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
SC config data is no longer stored within the CCC config itself
therefore it must be cleared separately.
Fixes#22539
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
GATT data shall not be considered conditional to BT_SETTINGS since
the data is stored in RAM it must also be cleared when unpairing.
Fixes#22514
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
smp_pairing_complete does actually clears flags so setting
SMP_FLAG_TIMEOUT must come after that.
Fixes#22786
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix bt_gatt_indicate using the wrong attribute pointer when a uuid was
provided as input.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Rename the scan recv callback info struct so that it reflects that it
is part of the scan recv callback. This will make it consistent with
future plans for advertising callbacks.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix the scanner using the advertiser identity instead of the scanners
identity, scanner always use BT_ID_DEFAULT.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Corrected configuration of BT_HCI_RESERVE for the RPMsg HCI driver.
This change fixes the following assert:
[net_buf_simple_headroom(buf) >= len] @ ZEPHYR_BASE/subsys/net/buf.c:881
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
