Add bond_deleted callback so that the application can keep track
of when bond information is deleted in the stack.
Bond information can be deleted by the application through bt_unpair
or automatically by the stack in some cases, e.g when
CONFIG_BT_KEYS_OVERWRITE_OLDEST is enabled and the oldest bond
is overwritten.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add advertising option for undirected one-time advertising, and
directed advertising using identity, and peer direct is RPA option.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Allow calling bt_le_adv_start with no connection object available
when not the option BT_LE_ADV_OPT_ONE_TIME has been set. In this
case the advertiser will be restarted once there is a connectable
advertiser object available.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Added implementation to acquire and initialize auxiliary
channel instance on use of periodic advertising.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When CONFIG_BT_GATT_NOTIFY_MULTIPLE is selected and the remote has
enabled support for using its procedure data can sometimes not fit
into the buffer since the multiple variant has a bigger header, so
instead of failing immediatelly this attempts to send the data using
the legacy PDU instead so those using bt_gatt_get_mtu - 3 can still be
sent.
Fixes#26106
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Enable Advertising Extensions by default if supported by the controller.
That is, do not enable it by default for BT_LL_SW_SPLIT.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
Change sets default value of Kconfig option BT_CTLR_LLCP_CONN to
BT_MAX_CONN. The default value should properly handle the worst case.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
Fix missing recalculation of skip value of the ticker being
inserted into ordered list, when it collides and is being
attempted to be inserted at next periodic interval.
This fix is for ticker compatibility mode which is used as
default for nRF51 series.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Adds idle wait callback to proxy by counting the number of pending
notifications.
Ensures that all connected nodes have received messages before resetting
the mesh stack.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Fix flash operation timeout due to incorrect use of
secondary ticker to abort any radio in use. Ticker id 0
is reserved for split controller's pipeline preempt timeout.
Using the same ticker id caused the secondary ticker to
not be started if controller is using the same ticker id
for pipeline preempt timeout.
Fixes#26333.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Reverse the order of these checks because invalid PDU type will
never be expected. If PDU type is invalid we should respond with
error 0x0002 - Invalid format.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Turn the GATT notify multiple feature off as default value.
This feature changes the behavior of the bt_gatt_notify API in a way
that might not be backwards-compatible.
This is because the notify multiple header is larger, and therefore
limits the amount of bytes that could otherwise have been sent in a
normal notify PDU for a given ATT MTU.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix use of conn_handle in LE Advertising Set Terminated event not
converting from serial Little Endian to native CPU endianness.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use an unspecified reason when disconnecting a connection that did not
have a pending connection in the host.
We don't allocate connection objects in the connection complete anymore
so using memory-capacity-exceeded is misleading.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This patch fixes an issue with the advertiser not resuming connectable
advertiser if the last bt_conn_unref happens from something other
than the disconnected callback.
In this case this last bt_conn_unref was from gatt.c notify_cb called
from application main thread.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix host RX thread being deadlocked. The deadlock occurs because the
RX thread is stuck waiting in conn_tx_alloc with K_FOREVER but if the
connection is disconnected only the RX thread can unblock it in the
handling of the disconnect event.
This commit fixes this deadlock by splitting the processing of the
disconnected event into two parts.
The part needed to unblock the RX is to release resources held by
unack'ed TX packets and mark the connection state as not connected
anymore.
The RX thread waiting for free_tx fifo and the TX thread waiting for
the bt_dev.le.pkts semaphore will both check the connected state after
having acquired them and will abort if disconnected.
The rest of the processing will be handled at normal RX thread
priority like normal.
Move the bt_recv_prio handling to the Bluetooth host when the host
has defined its own RX thread (CONFIG_BT_RECV_IS_RX_THREAD=n).
If the HCI driver has the RX thread (CONFIG_BT_RECV_IS_RX_THREAD=y),
then the responsibility to call bt_recv and bt_recv_prio correctly
falls to the HCI driver.
The helper function bt_hci_evt_is_prio() is replaced with
bt_hci_evt_get_flags() so that the HCI driver can do this correctly.
This decision to replace was made so that existing HCI drivers
maintained out-of-tree will fail at compile time with the new system.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Bluetooth: host: Move bt_recv_prio to host when RX thread is defined
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Save link key to settings_subsys, no need to re-pair after restart.
Overwrite old pairing records with aging counts.
Signed-off-by: ZhongYao Luo <LuoZhongYao@gmail.com>
The hci-cmd currently accepts only a 1 byte parameter. This
disables use of commands that requires more than 1 byte,
for ex. the feature exchange that requires a 16 bit parameter.
This commit allows a datafield parameter up to 65 bytes long.
65 bytes comes from the nr. of parameters for the
HCI_LE_Generate_DHKey command
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
Friend Request is also transmitted over local queue and
if both Friend and LPN features are enabled then we would
try to establish friendship with ourselves.
Fixes MESH/NODE/FRND/LPN testcases.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
The hardcoded value was arbitrary and interfered with message cache
mechanism causing invalid behavior and PTS test to fail.
Fixes MESH/NODE/RLY/BV-02-C.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
According to Mesh Profile Test Specification we should still
relay messages with DST address that is RFU.
Fixes MESH/NODE/RLY/BV-01-C.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Key refresh procedure was ignored on non-primary subnet.
Mesh Profile Specification v1.0.1:
3.10.4 Key Refresh procedure
"This procedure is used when the security of one or more network
keys and/or one or more of the application keys has been compromised
or could be compromised."
"It is possible to update each NetKey independently of all other
NetKeys. A Key Refresh procedure for one NetKey can be in a different
phase to another Key Refresh procedure for other NetKeys."
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Reset provisioning bearers when bt_mesh_reset() is called. Accept
another provisioning attempt after link close.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
This value was used quite often in the file so adding a
descriptive name should improve readability.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
The comparison of a current tx link transaction id caused
us to not send ack and in effect fail provisioning.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Fix the advertise object not release when a high-duty cycle directed
advertiser timeout happens. If the extended advertising feature has been
enabled in the host, but not supported by the controller then the
advertising object must be released in the connection complete event
since there will not be a advertising set terminated event.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix issue with directed advertiser not accepting connection request
from non-privacy enabled peer that has given us a non-zero IRK.
When device privacy is enabled then ull_filter_lll_rl_addr_allowed will
return true, and update the rl_idx to entry in the resolving list.
When the directed advertiser is not privacy enabled then lll->rl_idx is
set to FILTER_IDX_NONE and will not use RPA for the target address.
The check rl_idx != lll->rl_idx will then fail (0 != 0xff) and the
connect request is denied, even though all addresses matches on-air.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Removes the memset of the prov_bearer_cb in PB-GATT during resets. This
allows the provisioning link to disconnect and reconnect again without
having to call pb_gatt_open.
Fixes#26343.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Add explicit opcode check when handling received unknown
response PDU.
Without this, for example, an in progress Data Length Update
procedure state was reset when receiving an unknown response
to slave initiated feature request.
Fixes#26252.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add options for phy update procedure. User can now set no preference
option for a particular PHY as well as preference for LE Coded PHY
coding scheme.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
These functions don't work with buffers that do have fragments, instead
this replaces their usage with net_buf_{put,get}.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
ATT_PENDING_SENT does severely impact the throughput since multiple
packets no longer can be scheduled at same time, so instead of always
setting it regardless of the bearer/channel it is now only used for
EATT since that cannot set its own callbacks.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
bt_l2cap_send_cb may fail if there are no context available which means
that the request would not be sent, also due to the use of custom
callback it cannot be queued either so the only option is to return the
error and let the application handle it.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since the TX semaphore is used for all types of PDUs a request may have
to be put on the request list while there is no pending request pending
which means no response will be generated to trigger att_process,
previously this condition was handled by setting the request as
currently pending and append its buffer to tx_queue but this is no
longer efficient since there could be more than one channel active the
code should try all of them before queueing back to request list.
To fix this the request list will now be processed each time a PDU has
been sent.
Fixes#26070
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
ATT channel sent callback shall not be overwritting until the
operation completes as it can result in breaking flow control when
CONFIG_BT_ATT_ENFORCE_FLOW is enabled.
Fixes#25964Fixes#26071
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Disable the controller advertising extension feature default setting
until the feature is complete. The zephyr host requires the
LE Advertising Set Terminated event to function.
Without this event a peripheral connection cannot pair because the
local on-air address is not set, and the advertising state will not be
cleaned up, so advertising cannot be started again.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The frnd->last buffer can potentially be NULL if friend_clear is called
after the adv.c buf->busy check, but before the adv_start callback.
The current design is based on the adv.c thread being cooperative, and
therefore not yielding between the busy check and the adv_start
callback, but as the bt_le_adv_start call has to acquire a semaphore,
there's a possibility for friend_clear being called inbetween.
Fixes#26177.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Add warning about enabling the options below so that users are
aware that this is a security risk.
- CONFIG_BT_DEBUG_SMP
- CONFIG_BT_DEBUG_KEYS
- CONFIG_BT_OOB_DATA_FIXED
- CONFIG_BT_USE_DEBUG_KEYS
- CONFIG_BT_STORE_DEBUG_KEYS
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
