This commit adds a driver to simulate GPIO state and interrupts
using the keyboard when using SDL.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Add 2 properties to configure the "any movement" event.
* Ability to disable the interrupt latch
* Select movement mode
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Update RT11xx SOC DTSI files to use DT nodelabels on RT11xx SOCs,
instead of reencoding the base address of each peripheral in the M7
and M4 DTSI files.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Include files should not have compatible properties set. These do not
represent real hardware and should therefore not appear to do so, e.g.
by appearing in the bindings index as if they were a real hardware
peripheral.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Fix ordering of IOMUXC pinctrl selections for gpio pinmux setting.
This will allow the gpio_configure call to correctly set
mux settings for this SOC.
Fixes#50502
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The vref has to be set to 3000mV.
It is the voltage to find on the stm32F3.
is fixed by the platform to be lower or equal to VDDA.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add gpio-reserved-ranges property to gpio controllers on RT10xx devices
that have gaps in their GPIO numbering.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 qmspi. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 adc. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 pwm. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 espi. Update board dts, pinmux and espi driver
files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Apparently, downstream drivers are allocating devices using
DT_NODELABEL(alh0) and DT_NODELABEL(alh1) on a node with compatible
intel,alh-dai. These represent something like "channels" within the
device.
This is a strange choice. It would be better to do something like have
a property with the count of "channels", or one child node per
channel.
It is also a dtc error to have duplicate node names like this, and
will be an error in Zephyr's dtlib soon.
For now, work around this representation issue by replacing it with
something equivalent that doesn't have duplicate nodes. The
representation should be addressed at some point, but not by me.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Two issues:
- The nsmi_gpio107 node is being defined twice with the same pinmux
property value. This is an error when compiling the file with dtc.
Zephyr's dtlib doesn't currently error out on this, but it will soon.
Fix this by removing one of the redundant definitions.
- The eeprom_clk_gpio117 node label is referring to a node named
gpspi_clk_gpio117, which is already defined in the same file, but
with a different pinmux property value. This looks like a clear
copy/paste error causing invalid pinmux settings for the
gpspi_clk_gpio117 node.
Fix it by aligning the node name with the node label to create
a separate node with its own pinmux value.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Fix the incorrect temperature sensor (Die temp), the default value of
the vref-mv is 3.3V.
Actually, the vref is a board value rather than a soc one
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The FULLDRIVE description on the rt-iocon yaml file was
describing the slew rate and not the FULLDRIVE property.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
The LPC55s3x SOC comes with 2 FlexPWM peripherals each with 4 Sub-Modules.
Each Sub-Modules has 2 channels A && B.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
When the EXTI Line nb is not set as interrupt by default
(at reset value), the uart instance cannot waekup the
system from its low power stop mode.
The EXTI line must be specified, like with stm32WL55
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds a base binding for I3C controllers.
Note that this follows the Linux kernel 5.17 bindings under
Documentation/devicetree/bindings/i3c/i3c.yaml.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a few bits to the devicetree API tests for multi-bus
nodes where a bus can support multiple protocols. This uses
I3C as basis as I3C controller can support both I2C and I3C on
the same bus, while I2C controller cannot support both. So
this needs to make sure the correct bus macros are generated
if appropriate (and not generated if not needed).
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add support to at86rf212[b] sub-giga devices. This work enables use of
pages 0, 2 and 5 in accordance with IEEE-802.15.4/2003/2006/2011. The
proprietary speeds can be object of future work.
Note: It is recommended that user define a power table for better
performance, low emissions and to save power. A reference power table
can be found in the datasheet and should be used for tests only and
not on a final product.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The current version of power table is hardcoded in the driver which is a
problem when use devices in production. This change remove all hardcode
from driver and reimplement the feature to allow people create a table
which is defined in devicetree. The big advantage is that each board can
define their own table based on lab tests and allows use of FEM devices
inclusive.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Some reg size in fvp-aemv8r.dtsi isn't correct. This commit is used to
fix it.
- gic, the correct reg size is 0x10000 and 0x200000.
- uart0-3, the correct reg size is 0x10000.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
The property is similar to the usb_controller_index_t
enum that is available in the NXP SDK.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
This commit introduces the 1-wire master driver for maxim ds2485.
The ds2485 master has nearly the same (1-wire) feature set and
i2c-interface as the ds2477.
Therefore the common parts are extracted, but to avoid
any nda troubles only the ds2485 specific part is included.
Compared to older 1-wire masters, the ds2485 supports higher level
commands, supporting multi byte operations, search next, automatic crc
calculation.
In this driver only basic read and write operations are supported,
further hardware features are not yet utilized by the driver.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
