According to errata sheet, LSE driving-capability should not be set
to 0 or 1.
Set it to 2 as default value.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This driver provides an interface to SocketCAN interfaces of the Linux
system running a Zephyr application with the native_posix board. These
interfaces may be virtual or actual CAN buses.
Signed-off-by: Martin Jäger <martin@libre.solar>
Migrate information to DTS and get it from there on the code. Note that
for CAVS 15, the information is not migrated as there's no DTS entry for
it. It can be brought back (in the DTS) if TLB support is enabled for
it.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Reduce the default RAM usage for the NXP LPC MCAN CAN controller driver by
reducing the number of RX buffers, TX buffers, and filter elements.
The LPC MCAN uses regular SRAM as backend and the default configuration
causes SRAM overflows for many CAN tests.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add emulator functionality to the serial_test driver, so that it can be
used to simulate a device on the other end of the uart.
If you don't set the buffer-size property in the dts node, there should
be effectively no change from the previous behavior.
Signed-off-by: Jeremy Bettis <jbettis@google.com>
Add the DMA in the DTS binding for OCTOSPI interface
for the stm32 devices from STMicroelectronics.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
There are three types GD32 FMC.
GD32 FMC v1: its flash memory has 1 bank, page size is equal in the
bank, flash size is smaller than 512KB.
GD32 FMC v2: its flash memory has 2 banks. Page size equal within the
same bank but different between banks. Flash size can be up to 3072KB.
FMC v2 has two registers to control bank0 and bank1 separately.
GD32 FMC v3: its flash memory has 2 banks, use sector size as the
minimum operating unit, the sector size is not equal.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
The enet1g peripheral was missing in device tree for nxp rt11xx.
With this commit, the peripheral can be operated like the enet peripheral
with the eth_mcux (kinetis-ethernet) driver at 10/100 Mbit (no gigabit).
Signed-off-by: Nils Larsen <nils.larsen@posteo.de>
R-Car Gen3 platforms have up to 7 channels. Add the node to
the rcar_gen3_cr7 SoC series. In contrary to Linux, declare
only one PWM controller with 7 channels. So only one node is
written into dtsi file.
Signed-off-by: Pierre Marzin <pierre.marzin@iot.bzh>
Define RaspberryPi Pico ADC.
The ADC has internally connected temperature sensor,
Add property to enable this.
The ADC has a single VREF. VCC usually connects to it,
but it may not be in a case.
Add property to make configurable it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Use the clock control API to enable peripheral clocks. Note that both
GPIO and pinctrl drivers are updated at once since they share some IP
blocks.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Use the clock control API to turn on ADC clocks. Note that clock
selection is not yet implemented, so we still rely on custom rcu
properties for that.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This patch adds a clock control driver for GD32 platforms. It is
important to note that the driver is only able to handle peripheral
clocks, but not "system clocks" (e.g. PLL settings, SYS_CK, etc.). On
some similar platforms (STM32) this task is embedded in the same clock
driver, performed at init time but with no options to do any
manipulation at runtime via the API calls. The clock control API as-is
is really orthogonal to "system clocks", and it is arguably a bad idea
to embed system clock init code in a clock control driver. It can be
done at SoC level still using Devicetree as a source of hardware
description/initial configuration.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Remove the CAN_STM32FD_CLOCK_DIVISOR configuration option,
and add configuration via dts property clk-divider instead.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
There is only a single DMA in GD32F3X0. It is referenced as DMA in
datasheet, not DMA0 as in series that have > 1.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
i.MX8M Nano LPDDR4 EVK board is based on NXP i.MX8M Nano
applications processor, composed of a quad Cortex®-A53 cluster
and a single Cortex®-M47 core.
Zephyr OS is ported to run on the Cortex®-A53 core.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
1. Enable all cpu cores in soc dts and disable unused core in board dts.
2. Use default irq priority for uart interrupt.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Use node label to overwrite the flash and ram properties.
This removes some boilerplate as it is less verbose.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Changes to code:
1. Renamed CAVS_IPC API from common/include/cavs_ipc.h to
common/include/intel_adsp_ipc.h. Renamed all API functions and structs -
added "intel_adsp_" prefix.
2. Moved definitions from intel-ipc-regs.h and ace-ipc-regs.g to SOC
specific headers include/<soc_name>/adsp_ipc_regs.h.
3. Added new common intel_adsp_ipc_devtree.h header with new
macros to retrieve IPC and IDC nodes and register addresses.
Put those new macros in code replacing hardcoded values outside of
devicetree.
4. Changed documentation of IDC and renamed IDC register struct
to have common name between all intel adsp socs.
5. Removed excessive docs description on cAVS IPC protocol.
Changes to Devicetree:
1. Renamed in all CAVS boards .dtsi files content in IPC nodes:
- "cavs_host_ipc" node labels to "adsp_ipc" labels.
- compatible "intel,cavs-host-ipc" renamed to
"intel,adsp-host-ipc".
2. Added (previously missing) yaml file for "intel,adsp-host-ipc"
compatible.
3. Renamed in all CAVS boards .dtsi files content in IDC nodes:
- "idc" node labels to "adsp_idc" labels.
- compatible "intel,cavs-idc" renamed to "intel-adsp-idc"
4. Renamed intel,cavs_idc.yaml file to intel,adsp_idc.yaml
so it is suitable for both CAVS and ACE SoC family.
Moved it from ipm bindings to ipc bindings where it belongs.
Changes to Kconfig:
1. Renamed existing Kconfig option CONFIG_CAVS_IPC to
INTEL_ADSP_IPC.
2. For renamed INTEL_ADSP_IPC addded default value based on
status of the "adsp-ipc" and "adsp-ipc" node.
Signed-off-by: Andrey Borisovich <andrey.borisovich@intel.com>
Convert the device to be Devicetree based. Adjusted tests and other
areas that were using old Kconfig properties.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This patch adds D0i3 definition to available core power states in device
tree.
Additionally, changing the name of the OFF state to better reflect what
is in the documentation.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
Added code to enable platform specific Virtual Wire GPIOs. With this
change, able to send the USB-C overcurrent Virtual Wire event to
Meterolake SOC.
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
The clock bus of the specific SPI module (FIU) is under FIUCLK. The
previous commit misconfigured it to APB3_CLK. Although it won't
cause any issue as the driver doesn't use it. It should be fixed to
prevent confusion when reading the datasheet.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Some custom refresh profiles need to set the PLL and VDCS
registers. Add them as optional DT properties.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Add support for overriding display LUTs in the UC81xx driver. This
makes it possible to use different LUTs for the full and partial
refresh profiles.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Add a separate profile for partial refreshes. This makes it possible
to specify a separate refresh configuration for partial and full
refreshes.
The driver now transitions to full refresh mode when blanking is
turned on. It transitions back to partial refresh mode when there is a
write while blanking is off.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Introduce the concept of refresh profiles which are specified as a
child node in the device tree. This makes it possible to use different
overrides for different types of refreshes (full/partial).
The only profile that is currently supported is the "full" profile.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
This reverts commit fdd47f39be.
After v4.4.1, write-block-size is no longer needed to be 32-bytes
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
