Add BT_QUIRK_NO_AUTO_DLE quirk option for HCI rpmsg driver
when the Zephyr open source BLE controller is used.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix the error recovery mechanism that makes use of a temp variable
to avoid coverity issue without breaking error recovery.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Function spi_context_longest_current_buf() has been introduced in
commit ddef35c1da for the purpose of
getting the longest possible (potentially partial) SPI transfer
for which all currently active directions have a continuous buffer.
Such transfer can be done with taking advantage of a DMA that cannot
use scattered buffers (and this is the case for nRF SPI drivers with
which this function has been introduced).
Unfortunately, because of its inadequate name, later on this function
has been incorrectly used in other SPI drivers for getting the longer
of TX/RX buffers. And commit afc480f12b
recently "fixed" the implementation of this function, assumably to
adjust it to those incorrect uses, but this way it has also broken
the nRF SPI drivers.
Instead of restoring the original implementation of the function in
question, this commit adds a new one with functionality equivalent
to that original but with a hopefully less misleading name, and this
function is used in the nRF SPI drivers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Isochronous transactions do not support handshake phase
so in particular the ISO endpoint cannot be STALLed.
Isochronous transactions do no support data toggle sequencing
and should only send DATA0 PID.
Taking into consideration those requirements do not try to
clear dtoggle or STALL an ISO Endpoint in nRF USBD driver.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
The pull request #26269
drivers: SPI: Adds CS flags from devicetree
missed out on the APA102 led_strip driver, most likely due to the driver
not utilising the chip select signal until #25310
drivers: led_strip: Add support for external SPI CS on APA102 LED strips
Signed-off-by: Roman Vaughan <nzsmartie@gmail.com>
Enable by default the use of RAM buffers in the spi_nrfx_spim.c
driver for copying TX data located in flash (as SPIM peripherals
cannot transfer directly form flash). Without this patch, users can
get confused, especially when SPI transaction is used by an upper
level driver which does not check all error codes.
For size of the buffer, use the value used so far in the reel_board
default configuration and in the SPI loopback test, i.e. 8 bytes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Not possible to use device_get_binding() because we are
currently initializing DMA_1 device, so it is not ready and
device_get_binding() will fail.
Directly use string compare is more efficient.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Pins used for external LF clock source must be configured as
used by peripheral to allow using LFXO on network side.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Reimplement getaddrinfo to call SlNetUtil_getAddrInfo from the TI HAL
for a more robust implementation that supports both client and server
modes, and performs better error-checking.
Fixes#11890
Signed-off-by: Vincent Wan <vwan@ti.com>
Fixes#28275 by adding bluetooth HCI spi driver priority lower
(75 instead of 50) than SPI (70) to avoid device_get_binding
to return NULL because the device was not initialized.
Signed-off-by: Jeremy LOCHE <lochejeremy@gmail.com>
Enabled going to idle when waiting for low frequency clock.
Added 2 stages of starting LF clock when XTAL is used. First
stage is starting RC and then when it is ready XTAL is started.
It is done to get event/interrupt when RC is ready which means
that LF clock is available (but not stable).
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Added configuration for approach to starting system clock source.
There are 3 options: no wait, wait untill available, wait until
stable.
Added support for those modes in clock control driver which handles
low frequency source clock.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The driver is able to write with 32-bits word alignment of size
and offset, apart form sub-word writes for which it can write
part of word to aligned offset (which is a hack).
fixes#26729
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Use setting from devicetree to drive the default setting for
CORTEX_M_SYSTICK. We update the dts files to default systick to be
enabled since the major of cortex-m platforms utilize it by default
(except on Nordic SoCs, TI CC13x2/CC26x2 and MEC1501 in which we
default to disabled).
Fixes#25299
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename wdog_cmsdk_apb_enable to wdog_cmsdk_apb_setup,
this API is supposed to be called during driver probe based on
CONFIG_WDOG_CMSDK_APB_START_AT_BOOT (enabled by default).
Fixes: 03c7d9bd49 ("drivers: wdog: Update CMSDK Wdog driver")
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
"unused value" issue reported by Coverity (CID: 214211).
This is actually a true bug as reported error is erased
and not taken into account.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The value from socket() was directly assigned to offload_context, which
was treated as a unsigned integer when compared. This prevented the
following if statement from catching any errors, leading to random RAM
access. This is fixed by using an intermediate with the same type as the
return value, which is then assigned to offload_context after error
checking.
Signed-off-by: Abram Early <abram.early@gmail.com>
An unnecessary expression that doesn't compile was inadvertently
introduced in the device constification PR. Remove it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
When getting a hfxo manager for USB sybsystem incorrect symbol
was checked. This lead to always enabling HFCLK, even for nRF5340
which needs HFCLK192M.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This code had one purpose only, feed timing information into a test and
was not used by anything else. The custom trace points unfortunatly were
not accurate and this test was delivering informatin that conflicted
with other tests we have due to placement of such trace points in the
architecture and kernel code.
For such measurements we are planning to use the tracing functionality
in a special mode that would be used for metrics without polluting the
architecture and kernel code with additional tracing and timing code.
Furthermore, much of the assembly code used had issues.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
MCUX EHCI USB device controller supports a specific
number of bidirectional endpoints. Bidirectional means
that an endpoint object is represented to the outside
as an OUT and an IN Eindpoint with its own buffers
and control structures.
ep_abs_idx index refers to the corresponding control
structure, for example:
EP addr | ep_idx | ep_abs_idx
-------------------------------
0x00 | 0x00 | 0x00
0x80 | 0x00 | 0x01
0x01 | 0x01 | 0x02
0x81 | 0x01 | 0x03
.... | .... | ....
The NUM_OF_EP_MAX (and number of s_ep_ctrl) should be double
of num_bidir_endpoints. There is also no need to reserve
endpoint addresses for this controller type.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This adds supports for ISO packets so then can be transmitted and
received with userchan driver.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds supports for ISO packets so then can be transmitted and
received with H5 driver.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds supports for ISO packets so then can be transmitted and
received with H4 driver.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The host command peripheral device API abstracts how an embedded
controller sends and receives data from a host on a bus. Each bus like
eSPI, SPI, or I2C would implement their own host command peripheral
device. Each hardware device would then handle the necessary hardware
access to send and receive data over that bus.
The chosen host command peripheral device will be used by the host
command handler framework to send and receive host data correctly.
Signed-off-by: Jett Rink <jettrink@google.com>
When offloading only ZSOCK_POLLIN and DNS_EAI_MEMORY are available, so
use those instead of the standard ones.
Fixes#28069.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The dmamux requires HEAP size definition, so that k_malloc
is valid. The HEAP size config is defined in the common for
any stm32 soc instead of specific to dma Kconfig
Signed-off-by: Francois Ramu <francois.ramu@st.com>
VCO input frequency can be checked and set during compile time.
It unfortunately does not work for output frequency because macros in
HAL are defined together with uint32_t type.
This also fixes wrong check in case of HSI used as PLL source.
Signed-off-by: Jan Pohanka <xhpohanka@gmail.com>
timeslice terminology were used in connection with synchronization
using ll BLE ticker.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Rework ticker synchronization using newly introduced
radio synchronization API.
In kconfig synchronization using ll ticker become choice
option.
If CONFIG_SOC_FLASH_NRF_PARTIAL_ERASE is enabled the erase
timing is changed so intervals become similar to slots duration.
Previously interval was always ~90 ms, which looks like it was kept
so disproportional by oversight while the partial erase was
introduced.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Extract synchronization procedures using LL BLE controller
ticker to newly added synchronization API.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Introduced API which allows to decouple radio synchronization
mechanism from NVMC driver.
New API will allows to replace synchronization mechanism if required.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add console over Inter Processor Mailboxes (IPM).
This is useful for AMP processors like ADSP found on up_squared board.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The SX126x supports using DIO2 to control an TX switch, but only if
the switch can be operated using a single control signal. Add support
for RF switches that are wired to a GPIO instead of the radio chip
itself. This makes it possible to use RF switches that require two
control signals (one for the RX port and one for the TX port) by
wiring them to two GPIOs on the MCU.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
The stm32_dma_disable_stream first checked if the stream was
disabled and if so returned OK. If it wasn't disabled it
tried to disable it and returned -EAGAIN.
The function is used in loops that try to disable the stream
by calling this function and if it fails wait for 1ms and
retry.
Becuase this function the first time (if the stream wasn't
disabled already) fails there is always a 1 ms delay. For
the SPI driver, that has a RX and TX stream, this means
a 2ms delay between the last data and CS going high.
By first trying to disable the stream and than checking
if it succeded most of the time the first call disables
the stream and the 1ms delay isn't needed.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
- Fix GPIO CS timing when using DMA. When using GPIO CS the
CS select was enabled after the DMA started the transfer,
resulting in the first few bits being transfered while
CS was still disabled.
- Fix TX or RX only DMA transfers. When only a RX or only
a TX transfer was requested the DMA never finished.
For the RX only cause the size on the transfer was
calculated by taking the TX buffer length (0), this
caused problems.
For the TX only transfer the RX buffer was set to NULL,
this caused the DMA to acctually writing data to the
adress 0x00000000. By using the dummy destination buffer
it now only writes to valid memory.
- Add semaphore to signal that DMA is ready, instead of
just busy waiting.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Replace hardcoded sector size value in sample with sector-size
property added in dts binding file
Signed-off-by: Marin Jurjevic <marin.jurjevic@hotmail.com>
When building flash shell sample we get:
flash_stm32wbx.c:23:10: fatal error: shci.h: No such file or directory
23 | #include "shci.h"
Fix this by adding ifdef protection around inclusion of shci.h.
Fixes#28036
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
