Set stm32_dt_pinctrl_configure function as the unique entry point
to STM32 DT pinctrl management.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move pinctrl remap functions out of stm32f1 definition in order
to get it available to all series.
Allows use of more IS_ENABLED macros in calling drivers and make
code more readable.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add power-gpios device-tree binding property to power on module before
communicating with it. This pin is called CHIP_PU in case of ESP32{,-S2}
and CHIP_EN in case of ESP8266. Dedicated reset pin is available only on
the latter, however Espressif recommends (in ESP8266 Hardware Design
Guidelines) to use CHIP_EN instead. Follow those recommendations and use
power-gpios to reset chip if that is provided over device-tree.
Configure power-gpios and reset-gpios as inactive by default, so that
chip becomes ready after executing esp_reset() function, either if one
or both are provided over device-tree.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Most DT bindings use reset-gpios name when there is a pin to reset whole
chip. Rename wifi-reset-gpios to reset-gpios to be more consistent
between various drivers. Additionally this prevents confusion, as
somebody might think that this pin resets only WiFi, which is not true.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Remove two operation flags in the SPI configuration
instance, which disturb software controlled chip select
lines (CS never gets released).
Signed-off-by: Marco Peter <marco@peter-net.ch>
Application might need to know the GSM modem device name so
provide it in the header file.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When PPP is muxed, using uart_poll_out resulted in each byte getting
wrapped in a muxing header. This led to UART bombardment which
can quickly cause some modems to hang and panic. This was observed
regularly using a SIMCOM7600E modem.
A perfect fix would involve rewriting ppp.c, uart_mux.c and
modem_iface_uart.c to all use another UART API, but that would be more
invasive by several orders of magnitude than this one, which utilizes
the fact that the uart_mux implementation of uart_fifo_fill does NOT
require ISR context. Since the Zephyr UART API states that the behavior
of uart_fifo_fill outside of ISR context is implementation defined, this
should be kosher.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
These changes enable applications to restart the networking stack which
was previously not possible without rebooting the device. This was a
major show-stopper because it made power management impossible, and
furthermore made it impossible to recover from a bad modem state without
rebooting.
This has been verified to work on a SIMCOM7600E modem, both with and
without CONFIG_GSM_MUX enabled.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
The char pointer that is logged could get scoped out and so should be
strduped before logging.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
Thread implements couple of counters that require notification of failed
frame reception.
Implemented RX failed notification.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
Attempting to initialize PPP without first ensuring we're attached to
the network packet service will sometimes lead to "NO CARRIER" errors
when we initialize PPP with the modem. This has been observed
reproducibly on some SIMCOM7600E modems.
This commit holds off on PPP initialization until modem has reported
that it is indeed attached by using the "AT+CGATT?" command (see 3GPP TS
27.007)
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
The only user of the I2C instances is the esp32 driver. Move the
Kconfig symbols down to the esp32 Kconfig for the instances it needs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A GPIO's parallel output bit in the parallel output
registers is read-only until the AOD bit is set to 1
in the pin's control registers. The proper sequence to
preset the state of an output pin is:
Configure pin as input with AOD=1 in the control register
Set pin state in the parallel output register
Set direction to output in the pin's control register.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
The IIS2ICLX is a high-accuracy. ultra-low noise, low-power
two-axis linear accelerometer which can be interfaced through
either I2C or SPI bus.
Its high accuracy, stability over temperature and repeatability
make IIS2ICLX particularly suitable for inclination measurement
for industrial applications (inclinometers).
https://www.st.com/resource/en/datasheet/iis2iclx.pdf
This driver is based on stmemsc i/f v1.03.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Moved enabling SPI peripheral in front of the buffers loop.
Removed SPI DMA switching on in front of the buffers loop.
Signed-off-by: Łukasz Mazur <lukasz.mazur@hidglobal.com>
Removed SPI peripheral disabling when switching DMA to another buffer.
When using hardware chip select this would cause to stop driving
CS pin when swhitching buffers. This is different (and wrong) than
when used software CS.
Fixes#28833
Signed-off-by: Łukasz Mazur <lukasz.mazur@hidglobal.com>
Have the driver default to UART_CFG_PARITY_NONE if no parity property
exists rather than using default in binding.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fixes gpio_mcux_lpc_port_set_masked_raw function inside gpio_mcux_lpc
driver. Writing masked data is correctly done using device registers.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
ADC shell commands can be only executed on the property label
existing in the device tree. It is realized by the dynamic subcommand
returning existing ADC Label.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
The channel command has been extended with subcommands: id, positive,
and negetive. Some boards require positive input configuration before
measurement can be started.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Use dedicated shell macros so argument count can be validated before
the command handler is executed. This change simplifies the command
handlers implementation inside the adc_shell file.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Changed gain and reference commands to dictionary commands.
This change removes an obsolete look-up table (string <-> value)
for gain and reference commands.
Now, each modification of gain or reference value will require only
a dictionary command update.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
'remap' value can never be REMAP_FULL for usart.
Fix this value depending on the usart instance.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Stable API change: modify parameters of clock_control_async_on which
previously took a structure which contains list node, callback and user
context. Removing list node and replacing structure with two parameters:
callback and user context. List node is removed because it has no use
in current API.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Refactoring poll_out to be ready for handling preemption. uart_tx and
uart_fifo_fill modified so they are resilient to being preempted by
uart_poll_out.
Refactored uart_poll_out implementation to be common for interrupt
driven API and asynchronous API. In both APIs active state is detected
by evaluating state of ENDTX and TXSTOPPED events. If anyone is set it
means that new transfer can be started.
Patch is fixing existing issues:
- potential bytes dropping with flow control enabled
- busywaiting for ENDTX (asynchronous API) - poor performance
- potential bytes dropping during preemption
- potential uart_tx returning -EBUSY when interrupted poll_out
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
If neither a random address nor a specific local address is in the
device tree, then use the MAC address from the device information page.
Signed-off-by: Thorvald Natvig <thorvald@natvig.com>
Align all sensor drivers that are using stmemsc (STdC) HAL i/f
to new APIs of stmemsc v1.03.
Requires https://github.com/zephyrproject-rtos/hal_st/pull/5
(merged as b52fdbf4b62439be9fab9bb4bae9690a42d2fb14)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The interrupt enabling routine was called before the
chip enabling routine resulting in a runtime failure
when triggers are set.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This CL fixed the wrong comparison during searching the vw signal
that issued interrupt from MIWU in espi_vw_generic_isr().
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
In order to be in line with other DT_INST macros in zephyr code base,
swap the arguments order in following macro definitions:
*ST_STM32_DT_PINCTRL
*ST_STM32_DT_INST_PINCTRL
Update the users accordingly.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to pcintrl configuration using pcintrl helper
macros.
Pinctrl init sequence has to be done before bus_mutex initialization.
Driver dts bindings are updated to reflect usage of pinctrl-x
properties
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
