Report errors using logging subsystem so it is easier to
see the error location while debugging code.
Signed-off-by: Ievgenii Meshcheriakov <ievgenii.meshcheriakov@nordicsemi.no>
Make this driver multi-instance and use the new API.
Notes for sensorhub mode:
In case of multiples devices it is possible that some of them
has i2c slaves attached to it (sensorhub mode) but not the
others. Since the driver is configured in the same way for
all the instances (CONFIG_SENSORHUB=y), the routine that initialize
the sensorhub part does not fail anymore in case no slaves
are found for a particular instance. Instead, those non-sensorhub
driver instances will set the shub_inited flag to false and
will totally ignore the feature.
Notes for triggers:
In case of multiples devices the device pin the interrupt wire is
attached to can be different (INT1 or INT2 pin). So, this
information has been moved in DTS and then stored in the
specific instance config structure.
Currently the driver is able to handle a sngle interrupt line
at a time attached to either INT1 or INT2.
MOreover, the interrupt initialization for a driver instance proceed
only if the drdy has been configured in its DT, else it returns ok.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Make driver generic for multiple ILI displays. The adopted strategy is
to share all driver code except register initialization, which has been
found to have some specific registers/values depending on the
controller.
The driver has been adjusted to support multiple compatibles.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Improve the way the nrf_qspi_nor driver configures the SCK frequency,
to properly support QSPI also on nRF53 Series SoCs that use a different
base clock frequency (96 MHz).
Add also a relevant configuration in the spi_flash sample so that it
can run on the nRF5340 DK.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert handful of users of DEVICE_INIT to DEVICE_DEFINE or
SYS_DEVICE_DEFINE to allow deprecation of DEVICE_INIT.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When MEC15xx boots in MAFS, ROM bootloader performs activity over
eSPI flash channel prior to FW is loaded.
Need to clear STS_DONE during early eSPI driver initialization,
before enabling interrupts to avoid unexpected ISRs in FW.
Otherwise this would cause flash_lock semaphore to be incremented
due to ROM activity and result in FW's first espi flash request
to return immediately even before eSPI bus transaction completes.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
In current implementation, for Ping command, write data/payload is
queued in FIFO infinitely eventhough Ping command have write length
of '0'.
This issue is addressed in this patch.
Signed-off-by: Diwakar C <diwakar.c@intel.com>
This change adds IEEE 802.15.4g (Sub GHz) support for the
cc1352r.
The 2.4 GHz radio and the Sub GHz radio are capable of
operating simultaneously.
Fixes#26315
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
Obtaining irq_pin from dev leads to disabling interrupts
on unpredictable pin, as dev points to GPIO, not LSM6DSL.
Fixes#29721
Signed-off-by: Yurii Gubin <y.gubin@gmail.com>
For drivers that support CONFIG_DEVICE_POWER_MANAGEMENT there are some
cases that look like:
#ifdef CONFIG_DEVICE_POWER_MANAGEMENT
DEVICE_DEFINE()
#else
DEVICE_AND_API_INIT()
#endif
There is no need to special case this as the pm_control_fn argument to
DEVICE_DEFINE will just be ignored in the
!CONFIG_DEVICE_POWER_MANAGEMENT case. So we can cleanup the code a
little and remove the #else cases for the drivers that do this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Option to pause writing to the pseudo terminal until it is ready to
receive data. Useful for pseudo terminal synchronization with other
host processes.
Signed-off-by: Pavel Král <pavel.kral@omsquare.com>
When setting the MAC address, the ethernet driver has to call
net_if_set_link_addr() with the updated address. This was missing and is
added now.
See e.g.
https://github.com/zephyrproject-rtos/zephyr/pull/28874
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Replaces all existing variants of value clamping with the MIN and MAX
macros with the CLAMP macro.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
We should clear the pvm interrupts (snoop and pcie pmon lite interrupt)
at source before handling them.
This will make sure that we do not lose any interrupts that may have
been asserted to interrupt controller during the handling routine.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
So far there was 100ms timeout on allocation of RX net_pkt. This is too
little for cases when lots of data are incoming on pretty
fast (e.g. 1Mbps) UART interface and application layer does not consume
received network packets fast enough. Up to now in such cases all
incoming data was processed from UART and there was no data loss when
utilizing hardware flow control. However there was high chance that data
processed from UART could not be passed further to network stack,
because of the 100ms net_pkt allocation timeout. This happens for
example when low priority application does not have enough time to run.
Increase default RX net_pkt allocation timeout from 100ms to 5s, so
there is much more time to process network packets. Such timeout should
not harm, because only a dedicated RX thread will be suspended for that
time, resulting in suspending UART traffic if hardware flow control is
supported.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There is now a hardcoded 100ms timeout on allocating new net_pkt for
received data. Move that configuration to Kconfig, so that value can be
tuned according to application needs.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There is no reason to keep active stream socket when there was some data
loss. Mark such socket for closing and close it when all (so far)
received packets have been processed.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Following migration of all in-tree boards to device tree bindings
for SDMMC pins configuration, deprecate SDMMC related macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following migration of all in-tree boards to device tree bindings
for I2S pins configuration, deprecate I2S related macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following migration of all in-tree boards to device tree bindings
for USB pins configuration, deprecate USB related macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following migration of all in-tree boards to device tree bindings
for ETH pins configuration, deprecate ETH related macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following migration of all in-tree boards to device tree bindings
for ADC pins configuration, deprecate ADC related macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following migration of all in-tree boards to device tree bindings
for SPI pins configuration, deprecate SPI related macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following migration of all in-tree boards to device tree bindings
for I2C pins configuration, deprecate I2C related macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following migration of all in-tree boards to device tree bindings
for CAN pins configuration, deprecate DAC related macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following migration of all in-tree boards to device tree bindings
for serial pins configuration, deprecate CAN related macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following migration of all in-tree boards to device tree bindings
for serial pins configuration, deprecate (LP)U(S)ART related macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following migration of all in-tree boards to device tree bindings
for pwm pins configuration, deprecate PWN related macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Reworks the mcux ethernet driver to use DT_INST_FOREACH_STATUS_OKAY and
eliminate a lot of duplicate code between instance 0 and instance 1.
Renames the ERR_MISC interrupt to ERR due to an issue with the
underscore in the device tree preprocessor macros.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add uart bus interface to extended esWIFI driver. This enables all
Inventek modules with IWIN AT Commands firmware.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
The WIFI_ESWIFI_NAME config would be uselful when there is no device
tree alternative. The esWIFI driver already is on device tree and the
label property exists. This remove WIFI_ESWIFI_NAME Kconfig variable
and switch to device tree equivalent.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Remove global access to structure eswifi_spi_data variable. Instead,
add a method to pass access to that structure. This allows better
control to the data bus variable.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
This is a temporary workaround for an issue in TI's RF Driver
API. A subsequent release of the SimpleLink SDK will mitigate
the need for it and it can be reverted when hal/ti receives
that update.
Fixes#29418
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
This change reworks the cc13xx_cc26xx IEEE 802.15.4 driver to use
the TI RF driver API that is available in modules/hal/ti.
There are a number of benefits to using TI's API including
- a stable multi-OS vendor library and API
- API compatibility with the rest of the SimpleLink SDK and SoC family
- potential multi-protocol & multi-client radio operation
(e.g. both 15.4 and BLE)
- coexistence support with other chipsets via gpio
- vetted TI RF driver resources, such as
- the radio command queue
- highly tuned / coupled RTC & RAT (RAdio Timer) API
Fixes#26312
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
In case of h/w setup with multiples device instances it is possible
that some of them wants to use triggers but not the others (no
interrupt line.
Since Kconfig configuration is the same way for all the instances
(CONFIG_LSM6DSL_TRIGGER=y), the driver behaves differently according
to how the device instance has been configured in the DT.
If irq-gpios is present, then the driver initialize the interrupt
part, else it skip irq init and returns ok, but data->gpio != NULL
xis checked in trigger_set() API.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Enable ARR preload so that period or pulse updates are taken
into account synchronously with update event
(at the end of a ongoing period)
And thus avoid undetermined intermediate pulse.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Add support for configuring Ethernet pins using DT pinctrl entries. Note
that F1 series pinctrl support is not handled as the driver does not
support F1.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Channels 4..7 are multiplexed on adc16. The NXP HAL exposes
ADC16_SetChannelMuxMode but this function is not yet included
in Zephy. The following patch adds channel-mux-b to the dts
enabling the use of the alternate channels of 16 bit adc.
Signed-off-by: Andreas Dröscher <github@anticat.ch>
1. Merged the single/multiple ring(s) APIs, now these APIs
can handle both which requires passing a ring id.
2. Updated timestamp handling to match the new timestamp
implementation in the SDK driver.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Those devices can use several I2C address in order to address more
than 256 Bytes using 8bit addressing. Also several physical component
can be used as a contiguous memory.
Signed-off-by: Guillaume Lager <guillaume.lager@gmail.com>
This patch makes the initialization of workqueue earlier
for Nordic driver. Without this change Nordic devices
will fail tests/subsys/usb/device test as it is resetting
USB and by that will try to start already started workqueue
thread. This may lead to Zephyr fatal error.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This driver supports the PWM driven LEDs. The devices are created from
the DT nodes with a compatible property matching "pwm-leds". For each
child node a LED is created and its "pwms" phandle's node is used to
retrieve the PWM configuration: channel, period and flags. If some of
this properties are missing (it is the case for some PWM controllers),
then reasonable default values are used.
This driver implements the following LED API methods:
- led_on
- led_off
- led_blink
- led_set_brightness
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
With STM32Cube updates
https://github.com/zephyrproject-rtos/hal_stm32/pull/75
'..._hal_rcc.c' and '..._hal_rcc_ex.c' are now systematically
compiled, due to more and more dependencies from HAL IP on rcc.
So USE_STM32_HAL_RCC and USE_STM32_HAL_RCC_EX becomes useless.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
