The rf2xx driver is doing automatic retransmissions in hardware based
on whether ACKs are received or not. Currently the driver is not
invoking ieee802154_radio_handle_ack() as other drivers are doing and
required by OpenThread since 4fe1da9. This add rf2xx_handle_ack method
to ensures required ACK processing when driver performs TX.
Fixes: #21763
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The RF2XX driver not always sent ACK when a RX frame requests. This
happen because RF2XX transceiver asserts TRX_END interrupt after
confirm that the FCS is valid. The driver can now decode the frame
but in parallel the radio still processing the ACK frame. This will
sync the radio FSM state to ensure that ACK will be send.
Fixes#21659
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
So far, nRF 802.15.4 radio driver build was dependent on the 802.15.4
subsystem in Zephyr. While this was a reasonable approach for samples,
it prevented the radio driver from being built as a standalone entity,
which could be useful in some applications (e. g. running core nRF
802.15.4 radio driver tests with Zephyr).
Resolve this, by providing a separate set of Kconfigs for the radio
driver, therefore allowing to build it as a separate entity. The 802154
subsystem simply enables the radio driver module in this case.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The rf2xx driver needs GPIO driver to works. The RST, SLPTR and INT
are mandatory signals and driver uses DT to configure them. This add
the GPIO dependency on Kconfig.rf2xx file.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Same deal as in commit bd6e04411e ("kconfig: Clean up header comments
and make them consistent") and commit 1f38ea77ba ("kconfig: Clean up
'config FOO' (two spaces) definitions"), for some newly-introduced
stuff.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
OpenThread recently introduced CMake build system into its repostiory
so we no longer need autotools to build OpenThread libraries and can
integrate them natively.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add initial Atmel at86rf2xx transceiver driver. This driver uses device
tree to configure the physical interface. The driver had capability to
use multiple transceiver and systems with multiple bands can be used.
With this, 2.4GHz ISM and Sub-Giga can be used simultaneous.
Below a valid DT example. This samples assume same SPI port with two
transceivers.
&spi0 {
status = "okay";
label = "SPI_RF2XX";
cs-gpios = <&porta 31 0 &porta 30 0>;
rf2xx@0 {
compatible = "atmel,rf2xx";
reg = <0x0>;
label = "RF2XX_0";
spi-max-frequency = <7800000>;
irq-gpios = <&portb 2 0>;
reset-gpios = <&porta 3 0>;
slptr-gpios = <&portb 3 0>;
status = "okay";
};
rf2xx@1 {
compatible = "atmel,rf2xx";
reg = <0x1>;
label = "RF2XX_1";
spi-max-frequency = <7800000>;
irq-gpios = <&portb 4 0>;
reset-gpios = <&porta 4 0>;
slptr-gpios = <&portb 4 0>;
status = "okay";
};
};
At the moment driver assume two transceiver are enouth for majority of
appications. Sub-Giga band will be enabled in future.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Upper layers like OpenThread expect the radio driver to forward ACK
frame received by the radio.
Simulate this behavior on kw41z by recreating the ACK frame from the
available data.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
nRF5 driver did not utilize `ieee802154_radio_handle_ack` API, therefore
did not provide ACK frames to the upper layer. This commit fixes this
problem.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use the int_literal_to_timeout Coccinelle script to convert literal
integer arguments for kernel API timeout parameters to the standard
timeout value representations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This file contains redundant definitions of a bunch of nRF IRQ numbers
(not all, however) that only generates confusion, as enumeration values
provided by MDK can be used instead.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the named representation for no-wait to future-proof against a
change to the representation of timeout values.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a hidden Kconfig option indicating that a given SoC is equipped
with the IEEE 802.15.4 capable radio so that the corresponding driver
configuration can depend on it.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The nRF 802.15.4 radio driver should not include nRF52840 header
directly, but rely on soc.h instead. Otherwise, it will not work with
different SoCs supporting 802.15.4.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
move misc/byteorder.h to sys/byteorder.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move spi.h to drivers/spi.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move atomic.h to sys/atomic.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert DT_.*_GPIO_{CONTROLLER,PIN,FLAGS} ->
DT_.*_GPIOS_{CONTROLLER,PIN,FLAGS)
Used the following commands to make these conversions:
git grep -l DT_.*_GPIO_CONTROLLER | xargs sed -i 's/DT_\(.*\)_GPIO_CONTROLLER/DT_\1_GPIOS_CONTROLLER/g'
git grep -l DT_.*_GPIO_PIN | xargs sed -i 's/DT_\(.*\)_GPIO_PIN/DT_\1_GPIOS_PIN/g'
git grep -l DT_.*_GPIO_FLAGS | xargs sed -i 's/DT_\(.*\)_GPIO_FLAGS/DT_\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Found a few annoying typos and figured I better run script and
fix anything it can find, here are the results...
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
ieee802154_nrf5 checks if IEEE802154_DRIVER_LOG_LEVEL is set to debug
before initializing the "nRF5 rx stack". This leads to an undefined
reference error in case of the LOG module being disabled.
Avoids this behavior by using the LOG_LEVEL macro and setting it as
LOG_LEVEL_NONE in case of IEEE802154_DRIVER_LOG_LEVEL not defined.
Signed-off-by: Joao Cordeiro <jvcc@cesar.org.br>
Implement newly introduced `configure` API for nRF 802154 radio driver.
Increase maximum number of slots for Frame Pending bit information in
the radio driver.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The upipe specific configuration options are selectable unconditionally.
This commit makes them depend on the upipe driver being enabled.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
The following fix:
commit c8b17ec403
Author: Tobias Aschenbrenner <tobias.aschenbrenner@blik.io>
Date: Tue Dec 18 14:16:00 2018 +0100
fix: kw41z: Use correct mapping for dBm
Was using SYS_LOG_INFO and should be using LOG_INFO.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The radio API expects the setting of the TX-power in dBm. The actual
TX-power is however set by a 6bit register, which mapping between
register value and power in dBm is a lookup-table in the datasheet.
This mapping for the kw41z was off, which not only lead to incorrect
output power, but also to a maximal output power of only -1.9 dBm
instead of the possible +3.5 dBm.
Signed-off-by: Tobias Aschenbrenner <tobias.aschenbrenner@blik.io>
Signed-off-by: Franco Saworski <f.saworski@posteo.de>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This macro is slated for complete removal, as it's not possible
on arches with an MPU stack guard to know the true buffer bounds
without also knowing the runtime state of its associated thread.
As removing this completely would be invasive to where we are
in the 1.14 release, demote to a private kernel Z_ API instead.
The current way that the macro is being used internally will
not cause any undue harm, we just don't want any external code
depending on it.
The final work to remove this (and overhaul stack specification in
general) will take place in 1.15 in the context of #14269Fixes: #14766
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
unify the API of CCM alogrithm's implemation for TinyCrypt,
mbedTLS and cc2520 crypto device to make users easy to use.
Fixes#8339.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Some places were still using the old allocator. Using the new one does
not change any behavior. This will help to remove the useless data_len
attribute in net_pkt which legacy allocator was still setting.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
We have moved GPIO info to DT so the Kconfig symbols for GPIO lines
aren't used anymore. We can just remove them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Align ieee802154_nrf5 driver to a new radio driver API.
Utilize new radio driver features (CCA).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
15.4 MHR is no longer set in net_buf pointed by net_pkt, but in a
separate net_buf, hence we need to check that net_buf now to
determine if we need to wait for ACK or not.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This commit renames the nrf5_clock_control.h and
nrf5_clock_control.c files to nrf_clock_control.h and
nrf_clock_control.c, respectively, as they are used
in nRF9160 builds, as well.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit renames the CLOCK_CONTROL_NRF5 Kconfig symbol to
CLOCK_CONTROL_NRF. The change is required to aleviates confusion
when selecting the symbol in nRF9160 SOC definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
ieee802154_nrf5 uses net_analyze_stack function in a loop, which
prints logs at inf level. As net_core's log level is used in
this function which by default is set to inf, it kept spamming stack
usage logs.
Prevent this behavior by adding additional log level check in the driver
itself, so that this log will only be printed if
IEEE802154_DRIVER_LOG_LEVEL is set to debug.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Moving towards serialized fragmentation, adapting mac command creation
to avoid the need of ll_reserve etc...
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Do not initialize reset gpio on KW2XD SIP.
Modem's clock output is used by the SoC for the PLL.
Initialization of the reset gpio may result in the reset of the modem
and the crash of SoC.
Keep reset gpio low until modem initialization.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Fix overwrites update of indirect register.
Since the indirect register should be updated,
the parameter dreg should be false.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add a dts binding file for the cc1200 and move the Kconfig options for
SPI and GPIOs to DTS for the CC1200 driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As for Ethernet, up to ieee802154 L2's send to actually sent the packet.
It's currently unoptimized as 6lo compression, 15.4 fragmentation and so
on will reallocate net_buf etc... but it's the first step towards
removing ll reserve space and more.
Applying changes to Openthread L2 as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that the in tree user of cc2520 uses device tree to configure SPI
and GPIO params, we can remove and convert the driver to utilize DT
only. This means removing the Kconfig options that come from DT and
rename CONFIG_ to DT_ for those options.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all SPI controllers support DTS we can remove the Kconfig
support for non-DTS options. We also cleanup some defines that should
have be DT_MCR20A_ instead of CONFIG_MCR20A_.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Allow to set debug also for RAW_CHANNEL and set general debug template
instead of networking one.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Log configuration was included only in case NET_L2_IEEE802154 was
enabled. In case of open thread this is not the case.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Adding spaces around "=" when definining Kconfig template so
that is more consistent with overall style of these template
variables.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_PINS and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled gpio drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_GPIO_DEVICE and
HAS_DTS_GPIO.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_DEVICE and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Under GNU C, sizeof(void) = 1. This commit merely makes it explicit u8.
Pointer arithmetics over void types is:
* A GNU C extension
* Not supported by Clang
* Illegal across all ISO C standards
See also: https://gcc.gnu.org/onlinedocs/gcc/Pointer-Arith.html
Signed-off-by: Mark Ruvald Pedersen <mped@oticon.com>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Up until now, Zephyr has patched Kconfig to use the last 'default' with
a satisfied condition, instead of the first one. I'm not sure why the
patch was added (it predates Kconfiglib), but I suspect it's related to
Kconfig.defconfig files.
There are at least three problems with the patch:
1. It's inconsistent with how Kconfig works in other projects, which
might confuse newcomers.
2. Due to oversights, earlier 'range' properties are still preferred,
as well as earlier 'default' properties on choices.
In addition to being inconsistent, this makes it impossible to
override 'range' properties and choice 'default' properties if the
base definition of the symbol/choice already has 'range'/'default'
properties.
I've seen errors caused by the inconsistency, and I suspect there
are more.
3. A fork of Kconfiglib that adds the patch needs to be maintained.
Get rid of the patch and go back to standard Kconfig behavior, as
follows:
1. Include the Kconfig.defconfig files first instead of last in
Kconfig.zephyr.
2. Include boards/Kconfig and arch/<arch>/Kconfig first instead of
last in arch/Kconfig.
3. Include arch/<arch>/soc/*/Kconfig first instead of last in
arch/<arch>/Kconfig.
4. Swap a few other 'source's to preserve behavior for some scattered
symbols with multiple definitions.
Swap 'source's in some no-op cases too, where it might match the
intent.
5. Reverse the defaults on symbol definitions that have more than one
default.
Skip defaults that are mutually exclusive, e.g. where each default
has an 'if <some board>' condition. They are already safe.
6. Remove the prefer-later-defaults patch from Kconfiglib.
Testing was done with a Python script that lists all Kconfig
symbols/choices with multiple defaults, along with a whitelist of fixed
symbols. The script also verifies that there are no "unreachable"
defaults hidden by defaults without conditions
As an additional test, zephyr/.config was generated before and after the
change for several samples and checked to be identical (after sorting).
This commit includes some default-related cleanups as well:
- Simplify some symbol definitions, e.g. where a default has 'if FOO'
when the symbol already has 'depends on FOO'.
- Remove some redundant 'default ""' for string symbols. This is the
implicit default.
Piggyback fixes for swapped ranges on BT_L2CAP_RX_MTU and
BT_L2CAP_TX_MTU (caused by confusing inconsistency).
Piggyback some fixes for style nits too, e.g. unindented help texts.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Being stopped or not should not be a blocker on these settings (real
hardware can get these settings configured while not being in rx/tx
mode for instance).
Fixes#8528
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This makes it easier to distinguish them from "true" undefined symbols.
Internally, all int/hex literals are treated as undefined symbols, which
always get their name as their value. The C tools work the same way.
The plan is to turn references to undefined Kconfig symbols into an
error later.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These symbols were removed by commit 4e8f29f319 ("gpio: Refactor the
mcux gpio driver to use dts"). The settings should come from DTS now.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
ACK frames are handled on hardware level, so let's expose this
capability in order to avoid L2 waiting for these.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
L2 could take advantage of such hardware capability, when supported by
the device. This is also required for OpenThread.
Fixes#5714
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Adds dts bindings for the mcr20a wireless transceiver. The frdm_k64f
board supports the mcr20a via an Arduino shield, therefore the dts node
is added to the board dts. The kw2xd is a SiP and thus the mcr20a dts
node is added to the soc dts.
The networking samples using prj_frdm_k64f_mcr20a.conf have been broken
since the refactoring of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
And adding support for GPIO CS as well.
It looks like the driver could benefit from centralizing all SPI access
into a unique function, the protocol does not seem too convoluted to do
so, like CC2520 or CC1200.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
tx_bufs/tx_count and rx_bufs/rx_count can be hold in another dedicated
structure, thus reducing the number of parameters to transceive. This
permits to avoid using the stack when calling transceive.
Since we saved parameters, we can expose back the struct device pointer,
to stay consistent with other device driver APIs.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Move IP address settings from net_if to separate structs.
This is needed for VLAN support.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Driver is 'Busy' can be a warning message which can be enabled with
minimum debug level CONFIG_SYS_LOG_IEEE802154_DRIVER_LEVEL=2.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
CC1200 is a sub-ghz chip supporting 6 ISM & SRD bands: 169, 433, 470,
868, 915 and 920 MHz, with features dedicated to IEEE 802.15.4(g).
Current driver enables CC1200 against actual IEEE 802.15.4 Soft-MAC. 'g'
version support in the Soft-MAC will follow later.
The chip itself is closer to a bare metal radio modem than to a usual
15.4 chip: up to the user to provide the right RF settings for the
carrier band. Such settings can be generaten through TI's SmartRF tool.
Hopefully, for channel selection, this driver will be clever enough to
compute the proper register change without any special input from the
user. This will work for all the bands supported by the chip.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Old reference on driver's specific raw mode was still lurking around.
Removing those.
Fixes#5270
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
A very old reference to former net stack was still lurking around.
Removing it.
Taking the opportunity to clear up dependencies.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This fixes a regression from
https://github.com/zephyrproject-rtos/zephyr/pull/5018
The ieee802154 driver wouldn't build because nrf drivers/ieee802154
depends on the nordic ext drivers to build.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
- Renaming NET_L2_RAW_CHANNEL to NET_RAW_MODE
- Create a generic IEEE 802.15.4 raw mode for drivers
- Modify the IEEE 802.15.4 drivers so it passes the packet unmodified,
up to code using that mode to apply the necessary changes on the
received net_pkt according to their needs
- Modify wpanusb/wpan_serial relevantly
Fixes#5004
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The interrupt priority on KW41Z is from 0..3. The value of 0x80 is
invalid, so lets set it to 0 for now as all the other interrupt
priorities default to 0 right now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added conditionally enabled event state tracing support.
Needed for enhanced debug visibility of tight timed events where
normal print debug messages affect the timing of things. This is a
simple buffer that allows post analysis via gdb of what sequencer
events occurred.
Signed-off-by: David Leach <david.leach@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Removed some debug output and changed the level of others to reduce
the amount of information logged. The reason is that some of this is
causing false positive distractions.
- Removed enabling of FILTER error IRQ events. It isn't needed and is
only informational.
- Changed frame control AR bit inspection to use native retrieval
routine.
- Addressed some coding style issues.
Signed-off-by: David Leach <david.leach@nxp.com>
Changed the logic to reset the sequencer when a RX filter
failure has been detected. This also disables the RX timer
until the next watermark detection.
Signed-off-by: David Leach <david.leach@nxp.com>
- Reworked the driver logic around TX/RX to correctly handle the
expectations of the underlying 802.15.4 hardware IP.
- Fixed a problem with TX always reporting an error to the stack
which resulted in constant retries.
- Fixed bug in RX to TX transition which would occasionally cause the
driver to error the TX.
- Changed RX logic to ensure that invalid RX frames were not passed up
the stack.
- Simplified hardware timer usage to only use TMR3.
- Added RX watermark and TMR3 support to fix a hardware problem where
the hw IP can get stuck on a receive in noisy environments.
- Modified samples/net/echo_client and echo_server kw41z project config
files to provide enanced debug visibility into stacks and threads.
Signed-off-by: David Leach <david.leach@nxp.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Some "random" drivers are not drivers at all: they just implement the
function `sys_rand32_get()`. Move those to a random subsystem in
preparation for a reorganization.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Waiting for tx to complete should timeout after 10ms
instead of blocking forever in case ack is not received.
Signed-off-by: Kamil Sroka <kamil.sroka@nordicsemi.no>
Issue a error message, if the _mcr20a_read_reg fails.
Do not execute SPI burst read/write if the buffer is too small.
Unlock mutex if set_pan_id, set_short_addr or set_ieee_addr
fail.
Force abort of the sequence when the higher level changes the channel
even though a T or TR sequence is in progress.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
No need to send FCS bytes as the monitor_15_4 is configured to not
expect them. If we change the monitor_15_4 to use them, then we would
need to put correct values into these two FCS bytes.
So cleanest solution is not to send FCS bytes at all.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
set_ieee_addr, set_short_addr and set_pan_id are now unused by L2, so
removing their exposure through the radio API.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Further support will need work per-driver basis, as soon as the L2 will
be able to make usage of such support.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
802.15.4 is the networking hardware available in KW41Z SoC (and
supported by Zephyr). So, if networking in enabled, automatically
select the corresponding driver. This is similar to how frdm_k64f
automatically selects Ethernet driver, 96b_carbon selects BLE/IPSP
drivers, etc. (But we apply it on SoC level to reuse across the
boards.)
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The stack address was incorrectly specified when stack usage
was being debugged. This caused compiler to emit this warning
drivers/ieee802154/ieee802154_cc2520.c:1136:16: warning:
dereferencing type-punned pointer will break strict-aliasing
rules [-Wstrict-aliasing]
((struct cc2520_context *)(&__device_cc2520))->
^
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This patch allows the use of the MCR20A driver with KW2xD devices.
The clock output of the transceiver can be used as an input clock
for the PLL of the SoC. The hardware reset and CLK_OUT setup of
the transceiver should then be performed during the initialization
of the SoC. The driver is not allowed to do it again.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Some patches have been lost during rebase before the initial commit,
this path fixes it.
- correct copyright in registers definition header file
- fix undefined macro inside CLK_OUT configuration
- use the return value of k_sem_take if there is a timeout
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The net_stack_analyze function wants to look at the stack buffer,
but it is making assumptions on where this data is that are no
longer valid. Change to use the proper APIs for referencing this.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add support for KW40Z in the KW41Z IEEE 802.15.4 driver as both chips
expose almost the same radio registers.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
The chip seems to require a wait time before reading packet
data after the RX sequence done interrupt, as imidiate reading
of it will indicate a packet size of zero and cause the RX
sequence done to be continually retriggered.
In addition, the extra clearing of the interrupt flags can be
removed, as this is already done at the beginning of the isr.
Jira: ZEP-2278
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
fix misspelling in Kconfig files that would show up in configuration
documentation and screens.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
There is no need to unmask/mask the global transceiver interrupt
in kw41z_start/stop as the radio interrupt line is enabled/disabled
anyway with irq_enable/disable calls.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
- set state to IDLE if TMR1 expires, but CCA reports channel as free
- no need to check for CCABFRTX, as the hardware isn't setup to do
CCA before TX
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Sequence timeouts should be scaled to 16us, as TMR_PRESCALE was set
to 62.5kHz.
Also, radio warmup times and TX packet length need to be taken into
account.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Fix misspellings in Kconfig help text and made spelling of
RX and TX consistent (from reviewer comments)
Change-Id: Ie9d4c3863cd210e7a17b50a85a7e64156b6bf3d7
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I4ec03eb2183d59ef86ea2c20d956e5d272656837
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- net_pkt becomes a stand-alone structure with network packet meta
information.
- network packet data is still managed through net_buf, mostly named
'frag'.
- net_pkt memory management is done through k_mem_slab
- function got introduced or relevantly renamed to target eithe net_pkt
or net_buf fragments.
- net_buf's sent_list ends up in net_pkt now, and thus helps to save
memory when TCP is enabled.
Change-Id: Ibd5c17df4f75891dec79db723a4c9fc704eb843d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There have been long lasting confusion between net_buf and net_nbuf.
While the first is actually a buffer, the second one is not. It's a
network buffer descriptor. More precisely it provides meta data about a
network packet, and holds the chain of buffer fragments made of net_buf.
Thus renaming net_nbuf to net_pkt and all names around it as well
(function, Kconfig option, ..).
Though net_pkt if the new name, it still inherit its logic from net_buf.
'
This patch is the first of a serie that will separate completely net_pkt
from net_buf.
Change-Id: Iecb32d2a0d8f4647692e5328e54b5c35454194cd
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will provide the feature through Crypto API.
Change-Id: If6953a54b393544b019755ae73571effe0724e69
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
At the moment CC2520 configuration options are selected inside "TI
CC2520 Driver RAW channe" submenu like:
[*] TI CC2520 Driver support ----
[ ] TI CC2520 Driver RAW channel --->
Make RAW channel depends on TI CC2520.
Change-Id: I92879b7f4391f1842c012b6c03c78956e90b9441
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Allow user to set the four last bytes of a MAC address.
By default the bytes are selected randomly but for testing
purposes we need a way to specify the address in advance.
Change-Id: Ic9820a8026b327d1ee5025ab77fdc77f5778de67
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit adds missing RAW mode device to the driver.
Change-Id: I9ee9c41bc94b0ae202613ef707030033b46df1de
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
The code used net_nbuf_get_reserve_{rx|tx}_data() function to
allocate a fragment. Instead of that low level function, use
net_nbuf_get_frag() instead. There are few places this is not
possible or is too big change like in few test programs.
Change-Id: Ied7e2b7db352de998b200ffa6ff82471bfa5ebe3
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we receive lot of packets, it might happen that we exhaust
all the DATA buffers in the system. This would prevent from
us sending anything to the network.
Change this by splitting the DATA buffer pool into RX and TX
parts. This way RX flooding cannot consume all DATA buffers
that needs to be sent.
Change-Id: I8e8934c6d5fdd47b579ffa6268721b5eb3d64b6d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add the link type to net_if_set_link_addr() call. This fixes the
driver after changes introduced in
4eb2020055.
Change-Id: I72475a055ac805524b4b0f0c2380513e8f041368
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
Using net_nbuf_unref to release the net_buf so that we can
debug the allocations more easily. It is ok to use the original
net_buf_unref() too, we just miss some important net_buf
housekeeping information if done like that.
Change-Id: Ieb7b39ed525bfc46eb5c07a01f2a3a75fdbeb9fd
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The interface L2 address type is set at the same time as the
L2 address is set to the network interface. This is most
convinient place to set the address type.
Change-Id: I712d7357d075959eb79df3463141cfbc6d163a74
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit adds a driver for nRF5 802.15.4 radio. This driver
is a wrapper for the driver provided by ext/hal/nordic/drivers.
Change-Id: I20ee4aff3d1b994c621ba8eaab208d15d85e4c01
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
The interrupt processing of MCR20A was flawed and complicated.
This patch simplifies the handling of interrupts and reduces
the number of necessary SPI transfers.
Minor fixes:
- use mutex for the PHY access control
- remove unnecessary mcr20a_mask_irqb calls
- do not read RX_FRM_LEN twice
- increase timeout for sequence synchronization semaphore
if the log level greater than 1
- enable only the Sequence-end (SEQIRQ) interrupt
- fix magic in NET_DEVICE_INIT
- make the timeout values dependent on the log level
Change-Id: Ib3f64a092ffba91c80ff6e1d5cec995ab9d40bfb
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This commit changes the net_buf getter functions in nbuf.h
by adding a timeout parameter. These function prototypes
are changed to accept a timeout parameter.
net_nbuf_get_rx()
net_nbuf_get_tx()
net_nbuf_get_data()
net_nbuf_get_reserve_rx()
net_nbuf_get_reserve_tx()
net_nbuf_get_reserve_data()
net_nbuf_copy()
net_nbuf_copy_all()
net_nbuf_push()
net_nbuf_append()
net_nbuf_write()
net_nbuf_insert()
Following convinience functions have not been changed
net_nbuf_append_u8
net_nbuf_append_be16
net_nbuf_append_be32
net_nbuf_insert_u8
net_nbuf_insert_be16
net_nbuf_insert_be32
net_nbuf_write_u8
net_nbuf_write_be16
net_nbuf_write_be32
so they call the base function using K_FOREVER. Use the
base function if you want to have a timeout when net_buf
is allocated.
Change-Id: I20bb602ffb73069e5a02668fce60575141586c0f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit changes Kconfig prefix for ieee802154 drivers to
IEEE802154_*. This is done for consistency with config prefixes
used in other subsystems.
Change-Id: Ibbb4d96d2b748f4f13135bde85304ec34c5a90a6
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
This commit splits 802.15.4 drivers configuration into separate files.
Change-Id: Ie1bed862e8f4248240fef18bc211d0ee8ca1493c
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
The cause for this change is TCP. Until now, the radio strategy driver
(ALOHA or CSMA) was providing the actual nbuf, and not the buffer
fragment, counting on the fact that the loop was using
net_buf_frag_del() which made so, iteration after iteration, buffer
framgent to be always buf->frags. The problem with this logic is loosing
the fragments that might be still referenced by TCP, in case the whole
buffer did not make it so TCP can retry later and so on.
Instead, TX now takes the nbuf and the actual frag to send. It could
have been working with just a pointer on the data, and the whole length
of the frame. But it has been avoided due to possible future devices,
that will be smarter and run CSMA directly in the hw, thus it will
require to access the whole buffer list through the nbuf.
Change-Id: I8d77b1e13b648c0ec3645cb2d55d1910d00381ea
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of TI_CC2520_CHANNEL option NET_L2_IEEE802154_ORFD_CHANNEL is
used.
Change-Id: I9b0c0ff6b2c42070d05c5cf3e4dc33c364be9a5c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add driver and configuration for the MCR20A 802.15.4
transceiver.
Jira: ZEP-1429
Change-Id: I0b17b688220a47c2f0e5cde269064bbd0dec824a
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add common log level for all IEEE802154 drivers.
Change-Id: If92c96b14e630d4482aadf9cacb25662d6663399
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Move logging out of misc/ to its own subsystem. Anything related to
logging and any new logging features or backends could be added here
instead of the generic location in misc/ which is overcrowded with
options that are not related to eachother.
Jira: ZEP-1467
Change-Id: If6a3ea625c3a3562a7a61a0ba5fd7e6ca75518ba
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fibers do not exist anymore in unified kernel.
Also, let's just use that option directly so removing the internal
define which is then useless.
Change-Id: I1179d84401934b339d3a9ccd12f6145a120bcb2f
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Other driver than QMSI might have this limitation. Let's wait for a
future rework of SPI API to properly fix that.
Change-Id: Ibad382ce86e7479961b275c4851abf88ed581023
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Currently it's only possible to configure those GPIOs through
boards.<h/c> files and thus it's not relevant for board that do not
embed cc2520 but might get one wired to it, unlike
quark_se_c1000_devboard which directly embeds one cc2520.
Change-Id: I819bc1d2de707ea12eb70dc60a40b28f92666e51
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
* Moved networking code into subsys/net.
* Renamed net/yaip to net/ip at the same time.
* Fixed the tests/net to compile
* Fixed the Makefiles and Kconfig files in subsys/net
to use the new location of the IP stack
Change-Id: Ie45d9e8cb45a93fefdf969b20a81e3b1d3c16355
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The cc2520 driver RX thread did not like the stack information
collection macros defined in net_core.h. Both the cc2520 TX and
RX got the same variable name which did not compile.
This is now changed so that the first parameter is added to
the variable name to create a unique variable.
Change-Id: Ia41d01a71afd73af2ef31aa5f7a890a3cf0385aa
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the native IP stack is now the default, there is no need
for corresponding Kconfig option.
Change-Id: I08e4992f540f928a2b7378e8803e634e38725348
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit removes the legacy Contiki based uIP stack.
The new native IP stack must be used after this commit.
The commit also removes following things:
- legacy cc2520 driver
- legacy ethernet drivers
- legacy IP stack samples
and changes these things:
- disabled tests that only work for legacy IP stack
- select new IP stack by default
- enable random number generator by default as it is needed
by the new IP stack
Change-Id: I1229f9960a4c6654e9ccc6dac14a7efb9394e45d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Refactor code to exit earlier in case of error.
Change-Id: I9ff893f923ff877d69b0e985bb6e4159504e67cd
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Use the stack declaration macro from net_core.h which
allows user to see more information about stack usage
when using net shell.
Change-Id: Id3cc0fa49c5da79ba7d5573103864f1881e2f2e5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Hack in commit-id 835f93b8250abc0f3edbee9a99463fccac03597c was breaking
raw mode needed for wpan* adaptations.
Change-Id: If1ff96fa8170cc84e356fb0452e487f0ff174da5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is a hack, related to:
commit-id 835f93b8250abc0f3edbee9a99463fccac03597c
Change-Id: I7e305cef9ca908e2a71a011920663e1603ad8d6e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The 802.15.4 frame has a header and in the end after the payload a CRC.
Overall MTU is 127 bytes, but CRC is most likely going to be generated
by the device itself (offloading). Because the limitation of current
nbuf, it's not possible to keep this CRC in the buffer because it
require a user data size of 127 bytes but if we do so, IP stack will
fill in as much as it can as packet data, thus occupying the 2 last
bytes. This generates bugs. A perfect solution would be to generalize a
better handling of MTU and head or tail reserve data into nbuf, but
this will probably be solved in the future.
Change-Id: I1a0fee4d555e2717c1edd5afba399a1f17d9c7a9
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
commit-id 67c465d2cc introduced this
weird format by not removing unnecessary spaces.
Change-Id: I964185c8a894cfcf10e253e6d378c63ec02ad8d7
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Since the whole init level changes: all drivers and most of subsystems
are initialized at level POST_KERNEL. Unfortunately that broke legacy
tweaks on what to start first and after.
Let's raise cc2520 priority, still below net_init.
Jira: ZEP-1261
Change-Id: I0d91aa87a893584b3f5b39a193c823127961402f
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Thus setting a high priority of 2 on the rx fiber, as 0 is invalid.
Change-Id: I44a95f3648ca3fbf2eb699f1fa36963d6f3e5021
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
And take the opportunity to reduce the buffer size, as 127 is the 15.4
MTU, it has just engouh space on 128 bytes for the spi cmd plus the
frame.
Change-Id: Ifdeb83f85ab1adcdebc55bd72c38a98f18a86dbc
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Looks like getting an SFD interruption is not 100% reliable, so let's
just use a semaphore with a timeout on it instead of using
device_sync* routines.
Change-Id: I4e4115c7b939c95d7e75fbb33664d411e0a6e8cc
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Flushing rxfifo is necessary only on complete failure. It's badly
documented, but cc2520 errata mention that srxflush instruction should
be avoided as much as possible because it generates garbage in rxfifo
and kills incoming rx packet.
Change-Id: I486f7f4179103cf0c86c206821a0a61fec06178a
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
15.4 drivers are supposed to append LQI byte in the end of the buffer,
but of course there is no such thing in uart-pipe. Thus the bug, so
let's announce the proper length even if such LQI is missing.
Also align the debug output to proper length (FCS included)
Change-Id: Ib9ad86a8c22e1cf6437bc82e7fce11a489d0e761
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The upper IP stack uses the MAC address to construct the IPv6
address in SLAAC. Because of this the MAC needs to be stored
in big-endian format so that it can be used directly as is.
Change-Id: Ib31da56307017b4284031328772d4cb51d84fa23
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Let's not count the whole buffer length but only the very first frag's.
Up to L2 radio strategy to loop on every fragments and call tx for each.
(once sent, it deletes the fragment, so next fragment is always
buf->frags).
Change-Id: I94130fedfbecffdf62286bcb7f10563c776a255e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The given buffer can come with many fragments, but it's not up to the
hardware driver to send all of these but only the first in the list.
The overall fragments send procedure is handled in l2 level where the
radio transmission strategy loops over the list of framents and send
them one by one relevantly.
Change-Id: Ia7ae42ab4e9f8efb83bf07de6791918059b1e1c9
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As we use STXONCCA, RX will be stopped and reinstated afterwards.
We would be using STXON, since FRMCTRL1_SET_RXENMASK_ON_TX bit is set,
behavior would be the same.
Recalibrating the RX will uselessly abort any received frames before TX
or right after RX got reinstated. So, let's not do that and trust that
RX is anyway properly calibrated after TX.
Change-Id: Iac4fa03a175f8d139c1fc821de01caab1ec86e6b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Change DBG to ERR for error cases to get errors when only errors are
selected.
Change-Id: I51fd15900b1efb96d5dff36367afcdf380f11b88
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This prepends logs instead of [general] with [cc2520].
Change-Id: I148159a451981fbe3da638732f0e97900f76bc58
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
LQI is actually not provided as is, but should be computed from an
abstract correlation factor. See Section 20.6.
LQI is provided the same way as Linux does, so it can push it everytime
into the buffer.
Change-Id: I5de318db2c2581d7482cc16e41dc601130753a62
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fixing 80 chars limit by removing length computation:
We can count the FCS as part of the received length, even if AUTOCRC is
on. L2 layer is able to parse this out.
Change-Id: I3c824ed95d177570a07d04784798e14f5979c96b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
L2 RAW channel allows to use some functions of IP stack for RAW access
of network drivers. It is hidden from user and is selected by 2520 raw
driver.
Change-Id: I91dd09803052072dfddb7989d9d67c3a5840f89e
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add TI CC2520 driver allowing RAW access to radio interface similar
way Bluetooth user channel works. This makes possible to handle radio
channel inside external 802.15.4 stacks, for example export it over USB
and handle in Linux.
Change-Id: I61bb4c8b998ff1e47dc65427ac471f04ec8fea63
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Source contiki headers only for legacy driver
Change-Id: I356fd65ce9a4ee144c29eed1b51f2f0175315c1c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The bug was introduced by commit ID
a136a2587752cca256950b0efd5567ca29117d11
Which led to write junk as an address into cc2520 and thus made the
chip filtering out all unicast packet (as the incoming address never
matched)
Change-Id: I72009e795039f2059177a5b37a4bcf5d9717d65d
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
As it used directly as the ieee addr.
Propre endianess will have to be solved once this stack will be ported
to other arch than x86.
Change-Id: Ie556fabbd99cc5559025c8392d2f699facb007fa
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
We have no use of configuring cc2520, at built time at least, in
promiscuous mode. So let's get rid of these options for the new driver.
Change-Id: I17611c43bc7ba7961831beaa47cc4e2371f8de61
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This fixes bug setting incorrect long ieee802154 address and also
print address in BE byte order the same way as for Linux.
Change-Id: I774301e992372588dffa6ce5964fb119642a0a0d
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This driver is used for testing on Qemu where all "radio transmission"
will go through a pipe between 2 Qemus.
Change-Id: I5b4e75de82a98eb730ef9c70b460b4b60c0a60c3
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If no IP stack is seleceted, selecting one of the 2 cc2520 driver will
automatically select the relevant stack.
Change-Id: Icca22da190dc790ce6d302e14c45732f902e02ae
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Or the build will not go through.
Change-Id: I48f5f8661c4100a76e4624ea64d383055327e2a7
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
640 bytes seems too short, raising to 800 bytes.
Change-Id: I8c3418787939369e24fe47c23b0558c36f05af2c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
net_core.h is loading sys_log.h as well, so we need to be
first in order to setup some local definitions.
Change-Id: Ife482bd21e314aa5a5e88433eb8f9a560f9d53a6
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It's basically a copy/paste of original driver,
using native IP stack API.
This is meant to avoid cluttering the original driver
code with #ifdef, and in future it will help removing
the old driver as well.
Change-Id: I67d974ad7440d258583a5c7c6c7160e99210808c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Another driver will be made for native IP stack. This is meant
to avoid cluttering the code with #ifdef all over the place.
Instead driver will be transparently selected at built time.
Change-Id: I283f1194fece9357425b87794b5cb51938ca80d3
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The variable type mismatching was caught by LLVM.
Jira: ZEP-1179
Change-Id: If26c881d207a6cedc52b7589c5d7ebb2040c7ab7
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
In the unified kernel legacy layer, both these functions are
implemented as #defines which can't be put in a struct.
Eventually this driver should be updated to use new APIs, but
this will get it to at least build which is the priority.
Change-Id: Ic5dfb5b85ff3bd0d1646f542340642549a2b2e05
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
It's not FMSTAT<0/1> but FSMSTAT<0/1>
Change-Id: I836cf001b7baefe86df67f13a8759ea4e697a28e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will lead to conflicts and warning coming from Kconfig, so just
whitelist the board in the samples where this hardware is supported
Jira: ZEP-739
Change-Id: I4a2f3bdcfdb44fc75df0e272c237789ee16e0de1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Kconfig allows selecting NETWORKING_WITH_15_4_TI_CC2520 even if the
current board doesn't support it, and also selects it by default. This
breaks building the 15.4 sample with qemu_x86. Add a config option for
having CC2520 support and enable the choise only if it is available.
In addition, remove unused function from iee802154 code, as it now
fails the tests.
Jira: ZEP-697
Change-Id: Ib082f82acdd0f86d3306bbd3bb827f61b0fd0be1
Signed-off-by: Jaakko Hannikainen <jaakko.hannikainen@intel.com>
ieee802154 driver is now using new system log macros, update the
Kconfig variable to be a level rather than a bool and the .conf
files at samples.
JIRA: ZEP-311
Change-Id: I640e973d880c3a222cd7c13a72d35edf49ada3a8
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
- SREGs should use MEMRG/MEMWR instructions, FREGs use REGRD/REGWR
- REGRD/REGWR get the register address in the first byte along the
instruction.
Reported-by: Igor Modino <igor@emutex.com>
Change-Id: I0da9de5ecd4cab914c8711bd4276e7a2bc6147a5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Convert leading whitespace into tabs in Kconfig files. Also replaced
double spaces between config and <prompt>.
Change-Id: I341c718ecf4143529b477c239bbde88e18f37062
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Current QMSI SPI API does not handle asymmetric tx/rx buffers, and thus
it's up to cc2520 driver to manage the tx dummy bytes.
Change-Id: I97900946bcd8d96e9f039646bccd765c574c363e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
-EIO is an error code for operationnal error, not about invalid
argument.
Change-Id: I7064eaf01c6040d2e93ed43df3932d8baed1256e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
DEV_* error codes are deprecated and should not be used anymore. This
patch replaces DEV_* occurrences by the corresponding errno.h code,
according to the error code conventions.
Change-Id: I7b098a6107c390b46ed15aaeb9141627e9502727
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Adapting CC2520 driver to use the new callback format. That way, cc2520
will work on boards where FIFOP and SFD are hooked to a different GPIO
controller.
Change-Id: Ia40b17867000de26f332f36422f84bb3f20be2aa
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Disable reception and the oscillator as well when stopping. Revert
when starting.
Change-Id: I2a61066602267ac61e691ec9c20eb243de6fa076
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This prevents false packets to get accepted/generated into RX fifo.
Also, this will make AUTOACK working properly, when enabled. For some
reasons FRMFILT1 and SRCMATCH need to get their reset values written at
initialization, or then hw filtering won't work. This behavior is not
documented as it seems.
Change-Id: Ic0fe664dbc3b17d85d794c12b77bdbaafeb601f5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
For hw filtering and autoack to work, all the information should be
properly set in the chip.
That's a fix for the legacy radio/net API. From original code, these
were set from the application which is bad. But setting it from the
driver is not any better. ieee802154 and net stack should know what to
do, that will be fixed in the future.
Change-Id: I1688223e9488d10a423e788eb88ba1e251cb3f88
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Because the random number generator is very dumb at the moment,
the generated MAC address has always last byte set to 0.
The MAC address is used when generating IPv6 address.
In order to avoid IPv6 address collision, swap the last four
bytes of the MAC address so that the most random data is
at the end of the MAC.
Change-Id: I96c03654359e32f407bab3b29be0e3b08ee91bd7
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is a complete new cc2520 driver for zephyr. Intention is to fit
better within Zephyr device driver model.
- It's (almost*) ready to be instanciated as many times as necessary
- It's fully interrupt based on SFD and FIFOP (no pin polling)
- It's nicer to other sub-systems (it sleeps, no busy-wait loop)
- It still loosely complies to old legacy radio device driver model
*: GPIO API needs to be fixed in order to accept multiple callbacks, as
well as enabling callbacks to retrieve private data.
Notes:
- Hardware filtering does not work yet as the net stack, above, needs to
provide the relevant information for it (src/dst ieee802154 extended
addresses, short addresses...)
- A embryo of generic functions (txpower, channel, addresses...)
have been implemented but don't belong yet to any radio device driver
model. Such new driver model will come afterwards (soon?)
- SPI API would need to be improved to avoid as much as possible memcpy
as well as spi_slave_select() call.
Change-Id: I1fd6dfff28fba3984f6006d394ea12f1e763ac18
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
ieee802154 is a more relevant name. Applying the change in
include/drivers as well.
Change-Id: I7f7188ed0421045d7667303c375eeb8af1298b97
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>