Fix few instances of delayable work handlers using the k_work pointer
directly in a CONTAINER_OF pointing to a k_work_delayable.
This is harmless since the k_work is the first element in
k_work_delayable, but using k_work_delayable_from_work is the right way
of handling it.
Change a couple of explicit CONTAINER_OF doing the same work as the
macro in the process.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add Kconfig to set sleep timeout between empty read attempts in rx thread
for ethernet native posix driver.
Signed-off-by: Nicola Ochsenbein <Nicola.Ochsenbein@husqvarnagroup.com>
Binding like "arm,gic" call these flags "flags" whereas binding like
"intel,ioapic" call them "sense". Allow either to work
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
Now that all in-tree phys are declared under their mdio bus, drop the
`mdio` property and use DT_INST_BUS to find the bus.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
`k_thread_create` function has the 'adin' device passed as 1st
entry pointer. Therefore the device configuration is obtained directly
from the `dev` structure.
Adujst the code accodringly.
Fixes: 75dde83 ("drivers: ethernet: adin2111: add adin1110 support")
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Add support for ADIN1110 10BASE-T1L Ethernet MAC-PHY.
The ADIN1110 is an ultra low power, single port, 10BASE-T1L
transceiver design for industrial Ethernet applications and is com-
pliant with the IEEE® 802.3cg-2019™ Ethernet standard for long
reach, 10 Mbps single pair Ethernet (SPE). Featuring an integrated
media access control (MAC) interface, the ADIN1110 enables direct
connectivity with a variety of host controllers via a 4-wire serial
peripheral interface (SPI). This SPI enables the use of lower power
processors without an integrated MAC, which provides for the
lowest overall system level power consumption. The SPI can be
configured to use the Open Alliance SPI protocol or a generic SPI
protocol.
Documentation:
https://www.analog.com/en/products/adin1110.html
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Rework the devicetree definition for smsc91x to put the mdio and
ethernet device at the same level, and make the phy a child of the mdio
node.
This allows matching up the device initialization sequence with the
devicetree hierarchy.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Move few variable inside a case statement to avoid build warning for
unused variables in some specific configuration.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This driver implements an MDIO device. Enable the MDIO driver to avoid a
build error for:
orphan section `._device.static.3_CONFIG_MDIO_INIT_PRIORITY_'
Also set the proper compatible in mdio_shell so that the ethernet tests
build correctly.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
So far the init priories were:
enetc_psi0=60 < enetc_vsin=61 < emdio=70 < ethernet-phy=80
because the Ethernet PSI driver was doing global initialization for the
whole NETC complex, including enabling MDIO function (due to the way
the HAL works).
Change to use the default init priorities:
mdio=60 < phy=70 < eth=enetc_psi0=80 < enetc_vsin=81
by executing at an early stage the NETC global initialization. This also
allows to match the DT hierarchy representation of NETC with the
effective priorities assigned.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add initial support for NXP S32 GMAC/EMAC:
- it's a copy-implementation with DMA data buffers and buffer
descriptors in non-cached memory (buf len and ring size configurable)
- PHY interface selection only implemented for S32K3 devices as it is
SoC-specific
- no PHY driver integration, it works as a fixed link with speed/duplex
configured through devicetree
- supports multicast hash filtering, promiscuous mode, MAC loopback
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Change the eth-phy definition so that the phy is pointed by a phandle
rather than a child node, make the phy device a child of mdio. This
makes more sense from a devicetree hirearchy where the phandles have to
be initialized before the device itself, allows keeping the priorities
in check with CHECK_INIT_PRIORITIES.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Make ethernet phys childs of the mdio device and move the mdio device up
a level on the tree. That makes the device hierarchy coherent with the
required initialization priority and allows keeping the sequence in
check with CHECK_INIT_PRIORITIES.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix an unused variable build warning that was happening in certain
configurations. Move the variables in the only condition where they are
actually used.
west build -p -b nucleo_f429zi \
-T samples/net/cloud/aws_iot_mqtt/sample.net.cloud.aws_iot_mqtt
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Rename the phy-dev property with phy-handle to match the Linux
ethernet-controller binding and move it up to ethernet.yaml so that it
can be used by other drivers.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Refactor the ESP32 target SOCs together with
all related boards. Most braking changes includes:
- changing the CONFIG_SOC_ESP32* to refer to
the actual soc line (esp32,esp32s2,esp32s3,esp32c3)
- replacing CONFIG_SOC with the CONFIG_SOC_SERIES
- creating CONFIG_SOC_FAMILY_ESP32 to embrace all
the ESP32 across all used architectures
- introducing CONFIG_SOC_PART_NUMBER_* to
provide a SOC model config
- introducing the 'common' folder to hide all
commonly used configs and files.
- updating west.yml to reflect previous changes in hal
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Ethernet MAC addresses are not unique enough
use unique_device_ID full range (96 bits)
call crc32_ieee() to generate last 3 bytes of mac address
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
When ENET_ENHANCEDBUFFERDESCRIPTOR_MODE enabled,
MAC will automatic capture receive nanosecond from 1588TMR
and return back to ENET_ReadFrame. It is a highest accuracy
recv timestamp_ns, we do not need manually read from 1588TMR.
By this change, receive timestamp accuracy increase
from 20us to 200ns above.
Signed-off-by: Chen Caidy <chen@caidy.cc>
Add the RCR_PRMS field to toggle the promiscuous mode in the Ethernet
controller.
Register a set_config function that can make use of the field when
CONFIG_NET_PROMISCUOUS_MODE is enabled.
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Quite a few of the drivers meant for the POSIX arch
interacted with the host directly, and will not
work when we use an embedded libC.
Until we fix them, let's add the appropriate
kconfig dependencies to avoid users trying to build them.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Adds PHY driver. Works via MDIO API and
exposed ADIN2111 MDIO Clause 45
functions.
Link status detection is triggered by
ADIN2111 driver within offloaded IRQ
handler.
Supports:
- LED0, LED1 enable/disable
- Fatal HW error detection
- AN 2.4V tx mode enable/disable
The initialization order is important.
PHY 2 must be initialized after PHY1.
Therefore, it shall be defined after the 1st one
in the devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds initial ADIN2111 2-Port 10BASE-T1L (SPE)
switch support. Works over SPI.
The driver creates 2 interfaces, 1 per port (PHY).
Configures multicast and broadcast filters.
The same unicast is applied to both ports.
Supports:
- Link state detection
- CRC enable/disable
- Ports config set
- Ports ETH stats
Provides functions for MDIO driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Make it possible to be able to change speed and duplex for the
STM32H7xx and API_V2 from the configuration settings.
This exists for the non-STM32H7x already today, so this is basically
copying the code for the other STM32's.
Please note that ST has a series incompability. For F1 and F2,
the duplex settings are named ETH_MODE_FULLDUPLEX respective
ETH_MODE_HALFDUPLEX. For F4, H7 and F7 the duplex settings are named
ETH_FULLDUPLEX_MODE respective ETG_HALFDUPLEX_MODE.
This should really be queried from the PHY (as previous programmer have
written in the code). But while waiting for a proper PHY solution,
this is intended as a stop-gap solution.
Signed-off-by: Stefan Petersen <spe@ciellt.se>
Without this change, there's a difference between what the V2 Ethernet
HAL claims to be its capabilities in eth_stm32_hal_get_capabilities()
and what is actually enabled when CONFIG_ETH_STM32_HW_CHECKSUM is
disabled. This difference somehow causes the checksum in outgoing
packets to become 0, and hence seems to break networking at least on
some PHYs.
This commit disables HW checksums by default even when V2 driver is in
use, and this hence fixes networking when CONFIG_ETH_STM32_HW_CHECKSUM
is disabled.
This fixes#57629.
Signed-off-by: Ole Morten Haaland <omh@icsys.no>
This patch enables the PLL clock output and PLL ref clock
for second ethernet module in NXP's i.MxRT106x SoCs
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
Fix a compilation error for the ethernet driver smsc91x that
prevents the build with asserts enabled.
Signed-off-by: Luca Fancellu <luca.fancellu@arm.com>
rx_thread() is started by eth_initialize(), while dev_data->iface is
populated by eth_iface_init() (called by net_init()).
Usually eth_iface_init() has completed by the time rx_thread() hits its
idle timeout and accesses dev_data->iface, but in case of a time-intensive
SYS_INIT item between eth_initialize() and net_init(), this is not
necessarily the case, causing a NULL dereference. This can be forced by
putting a k_sleep(K_SECONDS(5)) at the top of eth_iface_init().
Start rx_thread() in eth_iface_init() instead (which runs after
eth_initialize() due to init priorities) to make sure everything is
initialized properly.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Allows Ethernet communication between "cells"
in the Jailhouse hypervisor.
The vring queue deviates from a standard virtqueue
so is implemented separately.
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
In the case that there is a situation where the controller
oscillator start-up timer doesn't expire, or the SPI can't
read the CLKRDY bit the driver would hang during init.
The config option ETH_ENC28J60_CLKRDY_INIT_WAIT_MS sets
the time that the driver will wait for OST before returning
an ETIMEDOUT error.
Signed-off-by: Dean Sellers <dsellers@evos.com.au>
Allow defining multiple instances of enc28j60.
Remove the ETH_ENC28J60_0 Kconfig option along with this.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Add the `full-duplex` property for the `microchip,enc28j60` node.
Replace ETH_ENC28J60_0_FULL_DUPLEX Kconfig option with this property.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
When running cppcheck on eth_stm32_hal.c it generated a warning for
shiftTooManyBitsSigned.
The solution is to make sure that the numeric value shifted is unsigned.
Updated to use BIT() macro as suggested by GeorgeGCV.
Fixes: #57336
Signed-off-by: Stefan Petersen <spe@ciellt.se>
Some single-precision float constants were being compared against
double-precision floats. Make the constants doubles.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
According to the datasheet for Marvell PHY [1], the mode field of the
General Control Register 1 Page 18 occupies bits [2:0]. However, the macro
PHY_MRVL_MODE_CONFIG_MASK specifies the mask as 0x3, which would
correspond only to [1:0]. The code in phy_xlnx_gem_marvell_alaska_cfg()
uses the mask to set the mode field to 0 to set "RGMII (System mode) to
Copper" mode. Unfortunately, different chips have different reset values
(111 or 000) and in first case, the code would set the field to 100,
instead of 000.
Without this change, ethernet on Avnet MicroZed (Marvel Alaska 88E1512 PHY)
does not work.
Signed-off-by: Marek Vedral <vedrama5@fel.cvut.cz>
[1]: https://www.marvell.com/content/dam/marvell/en/public-collateral/phys-transceivers/marvell-ethernet-phys-alaska-88e151x-datasheet.pdf
The SAM GMAC driver is not able to use all of the receive buffers
concurrently. Frames larger than (buffer size) * (buffer count - 1) are
silently dropped. Fix it by adding one to MAIN_QUEUE_RX_DESC_COUNT.
Fixes#55701
Signed-off-by: Brandon Del Bel <delbel@umn.edu>
Set STM32CubeHAL ethernet version in use as V2 by default, on series
supporting it (H7, F7, F4). Not yet available on F2 series.
Add a choice symbol to explicit V1 version as deprecated.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The SAM GMAC driver is not utilizing the entire receive buffer, causing
large packets to be dropped. Fix it by setting Receiver Packet Buffer
Memory Size Select to Full (RXBMS = 3) in the GMAC_DCFGR register.
Fixes#55701
Signed-off-by: Brandon Del Bel <delbel@umn.edu>
HAL API changes in ethernet and pwm
SoC RT595 power management code change
west.yml update
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
Remove all init functions that do nothing, and provide a `NULL` to
*DEVICE*DEFINE* macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a dependency on CONFIG_NET_L2_ETHERNET for
CONFIG_ETH_INIT_PRIORITY. This hides the Ethernet driver initialization
priority option in menuconfig unless CONFIG_NET_L2_ETHERNET is selected.
CONFIG_ETH_INIT_PRIORITY cannot currently be moved inside the
CONFIG_ETH_DRIVER if-statement in Kconfig as it is used outside the
Ethernet driver source files.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
