We don't support hard-coding vectors in this table anymore.
If someone really wants to do this, they can set
IRQ_VECTOR_TABLE_CUSTOM and define their own.
Change-Id: I45f49782ba5fefb0a02eab02ec96efd0019bc6d5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Remove CPU_MIGHT_SUPPORT_CLFLUSH as excessive.
Removal the flag requires adding per-SoC cnfiguration,
as some Quark models support clflush instruction, but
some do not, even on compiler level.
Change-Id: I655cba00c629db55d1813c199a2fe08b2d60ef4f
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Rearrange the source code in order to place functions
depending on clflush support detection into the proper
section.
Removed dependency between CACHE_LINE_SIZE_DETECT and
CLFLUSH_INSTRUCTION_SUPPORTED or CONFIG_CLFLUSH_DETECT.
Change-Id: I62ba5199763ed16c71f1d2fa372f6cc99b303e6a
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
The peripherals utilizing UART were required to register their own
ISR rountines. This means that all those peripherals drivers need
to know which IRQ line is attached to a UART controller, and all
the other config values required to register a ISR. This causes
scalibility issue as every board and peripherals have to define
those values.
Another reason for this patch is to support virtual serial ports.
Virtual serial ports do not have physical interrupt lines to
attach, and thus would not work.
This patch adds a simple callback mechanism, which calls a function
when UART interrupts are triggered. The low level plumbing still needs
to be done by the peripheral drivers, as these drivers may need to
access low level capability of UART to function correctly. This simply
moves the interrupt setup into the UART drivers themselves. By doing
this, the peripheral drivers do not need to know all the config values
to properly setup the interrupts and attaching the ISR. One drawback
is that this adds to the interrupt latency.
Note that this patch breaks backward compatibility in terms of
setting up interrupt for UART controller. How to use UART is still
the same.
This also addresses the following issues:
() UART driver for Atmel SAM3 currently does not support interrupts.
So remove the code from vector table. This will be updated when
there is interrupt support for the driver.
() Corrected some config options for Stellaris UART driver.
This was tested with samples/shell on Arduino 101, and on QEMU
(Cortex-M3 and x86).
Origin: original code
Change-Id: Ib4593d8ccd711f4e97d388c7293205d213be1aec
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Currently the build system has hardcoded values for the -march/-mcpu
which identify what architecture should be used when compiling ARM code.
For processors such as the STM32 this will need to be defined by a per
SOC process.
Change-Id: Ia8158cd687d8d0432ea420e204bb2bc67d33a054
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
This patch updates some help sections to remove the "ERROR:
Unexpected indentation" messages during hmtl documentation
generation.
Change-Id: Idcdc17727b921b6145f9eb28d85975ceca273ce2
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Clockgating was disabled for RTC and disabling RTC had no
effect on Quark SE boards.
Change-Id: I67448d5582a206fc7a68d763d504e9f743043b53
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
ia32/soc.h is only used by QEMU, but QEMU's INTx routing does not follow
the "standard design consideration".
Instead, the pins are swizzled based on the PCI slot. They are then
routed to IRQs based on the PIIX PIRQ configuration.
For simplicity use hard-coded values for the PIIX PIRQ configuration,
though it may be desirable in the future to determine these dynamically.
Also change the number of PCI buses to 1 and remove irrelevant comments.
Change-Id: I1592009a43dd8a9c5a7c54788fba52f14687ba35
Signed-off-by: Ido Yariv <ido@wizery.com>
The app-facing interface for configuring interrupts was never
formally defined, instead it was defined separately for each arch
in their respective arch-specific header files. Occasionally these
would go out of sync.
Now there is a single irq.h header which defines this interface.
To avoid runtime overhead, these map to _arch_* implementations of
each that must be defined in headers pulled in by arch/cpu.h.
Change-Id: I69afbeff31fd07f981b5b291f3c427296b00a4ef
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The deleted defaults cannot be overriden by defaults defined
in SoC's Kconfig file. The number of IRQ priority level was
always one, and this caused some code to be dropped within
the fast IRQ handling code. When the electrons aligned in
certain way, undesired effects were observed (e.g. exception,
faults, etc.) when regular IRQs were mixed with fast IRQs.
Moreover, ARC cores are high configurable on hardware level.
So let the SoC config define these values instead.
Change-Id: I2a338d2efc814c46b0f68ab100fc0f66ae0fb60c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
That implementation is not galileo-specific, but rather a generic way of
rebooting an x86 target. Needs SoC support.
Change-Id: I9c3374a8ab57a624d9d9b7090260c5b11fe4e773
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This patch removes the default value from some platform/SoC specific
options which are declared in drivers/i2c/Kconfig because 1) most of
the time they are not valid values and 2) the correct values are
already set in the SoC Kconfig.
It also moves the interrupt priority definition from the driver's
Kconfig to the platform's Kconfig since it is a platform-specific
configuration.
Change-Id: If3c260b9a2fa095de47a99eb7fa5b947efefe9b1
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch removes the default value from some platform/SoC specific
options which are declared in drivers/spi/Kconfig because 1) most of
the time they are not valid values and 2) the correct values are
already set in the SoC Kconfig.
It also moves the interrupt priority definition from the driver's
Kconfig to the platform's Kconfig since it is a platform-specific
configuration.
Change-Id: Ic992749b3210ed8a2e454edece41ceca5edbaf2e
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch removes the default value from some platform/SoC specific
options which are declared in drivers/gpio/Kconfig because 1) most of
the time they are not valid values and 2) the correct values are
already set in the SoC Kconfig.
It also moves the interrupt priority definition from the driver's
Kconfig to the platform's Kconfig since it is a platform-specific
configuration.
Change-Id: Id00f7907fa55025011dabce6e282a9623be23831
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Base address registers and IRQs are set in Kconfig.
Set proper SPI default to various quark_se_ss based boards.
Change-Id: Iadaae551f441457bef334f94f68cafa7c3e499d0
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Though it's an ARC core, Quark SE SS does not follow the same registers
mapping as the official DesignWare document. Some parts are common, some
not.
Instead of bloating spi_dw.c with a lot of #ifdef or rewriting a whole
new driver though the logic is 99% the same, it's then better to:
- centralize common macros and definitions into spi_dw.h
- have a specific spi_dw_quark_se_ss_reg.h for register map, clock
gating and register helpers dedicated to Quark SE SS.
- have a spi_dw_regs.h for the common case, i.e. not Quark SE SS.
GPIO CS emulation and interrupt masking ends up then in spi_dw.h.
Clock gating is specific thus found in respective *_regs.h header.
Adding proper interrupt masks to quark_se_ss soc.h file as well.
One of the main difference is also the interrupt management: through one
line or multiple lines (one for each interrupt: rx, tx and error). On
Quark SE Sensor Sub-System it has been set to use multiple lines, thus
introducing relevant Kconfig options and managing those when configuring
the IRQs.
Quark SE SS SPI controller is also working on a lower level, i.e. it
requires a tiny bit more logic from the driver. Main example is the data
register which needs to be told what is happening from the driver.
Taking the opportunity to fix minor logic issues:
- ICR register should be cleared by reading, only on error in the ISR
handler, but it does not harm doing it anyway and because Quark SE SS
requires to clear up interrupt as soon as they have been handled,
introducing a clear_interrupts() function called at the and of the ISR
handler.
- TXFTLR should be set after each spi_transceive() since last pull_data
might set it to 0.
- Enable the clock (i.e. open the clock gate) at initialization.
- No need to mask interrupts at spi_configure() since these are already
masked at initialization and at the end of a transaction.
- Let's use BIT() macro when relevant.
Change-Id: I24344aaf8bff3390383a84436f516951c1a2d2a4
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This patch fixes the QMSI SPI shim driver so we are able to use it in
Quark D2000 based platforms. The only change required to enable this
driver is an #if guard in spi_qmsi_init() because the macro QM_SPI_MST_1
and the function qm_spi_master_1_isr are not defined in QMSI headers
from Quark D2000.
Since this drivers is now properly working on Quark D2000, this patch
also sets the QMSI driver default options in arch/x86/soc/quark_d2000/
Kconfig.
Change-Id: Ic6e2f7f5a2c3f350ddf360b23ffab6b812948572
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch removes the default value from some platform/SoC specific
options which are declared in drivers/watchdog/Kconfig because 1) most
of the time they are not valid values and 2) the correct values are
already set in the SoC Kconfig (e.g. arch/x86/soc/quark_d2000/Kconfig).
For Quark D2000, the IRQ priority options (WDT_DW_IRQ_PRI and WDT_QMSI_
IRQ_PRI) values are set to '0' since the priority information is ignored
by the interrupt registering system (the interrupt vectors are fixed in
this SoC).
Change-Id: I8f36c0f0e56211cdee3f2c6fc90c7dcac0a1b5aa
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch removes the default value from some platform/SoC specific
options which are declared in drivers/rtc/Kconfig because 1) most of
the time they are not valid values and 2) the correct values are
already set in the SoC Kconfig (e.g. arch/x86/soc/quark_d2000/Kconfig).
For Quark D2000, the RTC_IRQ_PRI default value is set to '0' since the
priority information is ignored by the interrupt registering system
(the interrupt vectors are fixed in this SoC).
Change-Id: I70de889cfd22e65f0e7acf7e57ddc6439f028394
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
The name already set by the driver's Kconfig is correct, so overriding
it only causes confusion.
Change-Id: Ia6405786fdfdf103c922517c8140a07a9de387e0
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This patch fixes the GPIO QMSI shim driver so we are able to use it in
Quark D2000 based platforms. To enable this driver we have to add a few
#if guards because some macros and functions (e.g. QM_AON_GPIO_0 and
qm_aon_gpio_isr_0) are not defined in QMSI headers from Quark D2000
(this SoC doesn't support the Always-On GPIO controller).
This patch also adds the QMSI driver default options to arch/x86/soc/
quark_d2000/Kconfig.
Change-Id: Ia16a345e1de3008f167ed66f891834607c05f4a2
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This adds support to the AON GPIO controller using the QMSI driver.
In order to enable it, the following configuration options must be set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="PATH TO LIBQMSI"
CONFIG_GPIO_QMSI=y
CONFIG_GPIO_QMSI_AON=y
Change-Id: I5a1a232d97741ad7fdbf40d8aea5a835e5b4e724
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This adds a NULL check against the reset vector for ARC.
If the reset vector is null, do not start the ARC core
as there is nothing to execute, and will probably cause
the whole SoC to stall.
Change-Id: I78d77b3e5940a205e05c13369f889cf9c5955487
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This patch changes both Quark SE and D2000 Kconfig files to enable the
WDT_DW driver by default if the WATCHDOG is enabled. This way, we keep
it consistent with the approach we already follow for others peripheral
drivers (GPIO, I2C, SPI).
Change-Id: I9d8b81c0e659b1408137deb71e33dacf6d4108c2
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch changes both Quark SE and D2000 Kconfig files to enable the
RTC_DW driver by default if the RTC is enabled. This way, we keep it
consistent with the approach we already follow for others peripheral
drivers (GPIO, I2C, SPI).
Change-Id: I4910e501c105b6218d046080c47b1e7a42eced92
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch fixes the QMSI I2C shim driver so we are able to use it in
Quark D2000 based platforms. The only change required to enable this
driver is an #if guard in i2c_qmsi_init() because the macro QM_I2C_1
is not defined in QMSI headers from Quark D2000.
Since this drivers is now properly tested with Quark D2000, this patch
sets the QMSI driver default options in arch/x86/soc/quark_d2000/Kconfig.
It also adds the wiring information required to test the i2c_lsm9ds0
sample app in the Quark D2000 CRB.
Change-Id: I4be03c09304da5a66ac663e48b1d72225eb5651d
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
In case the I2C_QMSI driver is selected by the user, enable both I2C
contollers by default. This is the default behavior for I2C_DW driver
as well.
Change-Id: If3dc8eb0a266fde7f598f7b12370e5be903aafed
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Always use braces, even on one-line code blocks.
Change-Id: Ic9e60db7f851d2fbee5bfd79cd810df23c0c5db0
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This is part of an ongoing development of power management
support in zephyr. This implementation builds upon an existing
hook interface and adds more enhancements. This was tested
with reference implementations on quark_d2000 and quark_se.
Change-Id: I28092b7ec90ce1f1cc661cf99ca88708910c8eb2
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Renamed functions and labels used in power management code
according to coding convention. Only doing this to relevant
functions and not touching functions that will be removed in
future patches.
The stack used during resume would be necessary so
renamed that too.
Change-Id: I2f09a349b0f0fd6520c11b4cd73f4c8e1a13f100
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
GlobalTss is not defined anywhere. This was originally designed
to be used by power management code to switch thread context to
kernel resume location. An alternative to this method would be
implemented.
Change-Id: I9ae14ba14f9573d8bd8579869cdee9cf85a5684a
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Modifications to timer drivers and interrupt setup, to manage
the tickless idle for the x86 architecture
Change-Id: Ie02d484b7e5636de6ea382ba2eeed57e704c8498
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Looking at the IDT in a debugger is confusing, add a pretty-printing
function.
Change-Id: Iacc5e204e5d11e3e875c75ddf6d2e2e80b230299
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
It was, in a nutshell, wrong. Fortunately, the incorrectly
specified fields weren't being used by anything.
Change-Id: I0fa63fa16a267502744a7a2c82865c7de8b5446e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We have a new policy: users should not be able to configure
an interrupt with "forbidden" priority levels, and any priority
levels with special semantics will be activated by flags.
Change-Id: I757c19cfedcb1d0938eaf4da348ddafb71b3e001
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
DEBUG isn't tied to any config option. Just use assertions.
Most of the time return values aren't being checked anyway.
Change-Id: I7457dcf00e18505bd6bcd98d46288545c03b5fbc
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Having priority levels 0 and 1 reserved on x86 due to implementation
details on how the CPU uses the vector table is confusing to users,
and makes it unnecessarily difficult to share drivers between arches.
Now on x86, priority levels 0 and 1 are available. Semantically, all
priority levels have had 2 subtracted from them.
It is no longer necessary to specify a priority level when the
vector itself is specified. If an IDT entry has a specific vector
associated with it, any priority argument is simply ignored.
In gen_idt, some simplifications have been made:
- The printed representation of a generated entry now fits on one line
- Some checks being done in validate_priority() were redundant, as
generate_interrupt_vector_bitmap() also ensures that there are
sufficient free vectors within a priority level.
Change-Id: I26669d8ee0a53f48fbc2283490a8c42d8b1daf8e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The argument to _common_dynamic_exc_handler() in the C domain
was still being set up the Sys V way. Arguments are popped off the
stack in reverse order, so _ExcEnt pushes *pEsf for arg 2, and then
the stub pushes the stub_num for Arg 1.
For IAMCU case, *pEsf is placed in EAX which is where argument 1
lives; static exception handlers take just one argument. However
since we're calling _common_dynamic_exc_handler we also need to
supply the stub_id, which we put in EDX (where arg 2 goes).
Rather than swapping things around at runtime the prototype for
_common_dynamic_exc_handler() is adjusted to fit the calling
convention in use.
Change-Id: Id43cbc3b86d90f941cea771678b2796ae5f1358d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Adds the driver to utilize the I2C/TWI interface on Atmel SAM3
family processors for I2C communication.
Note that this currently only supports master mode. Limited
testing has been done using the Fujitsu FRAM sample app.
Change-Id: Ibdb8277e47dd9450b49a66a95421eb1ffb1c4eb4
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Adds the struct to describe PDC (Peripheral DMA Controller).
The PDC is being used by peripherals to initiate DMA
transfers.
Change-Id: Ida2a20810c4f2ef972e9669c45e22da07c1576ab
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Adds logger support to iamcu core for the following features:
- context switch logger
- interrupt logger
- sleep logger
Change-Id: Icfbd5fa787633045ba2895e8c28b652c55575b86
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
The common stub code didn't prefix the arg to 'mov' with a
'$', causing the assembler to generate code which tries to
dereference the argument before sticking it in EAX.
Change-Id: I0e201f799565d9709e3969b82ae2eb3f93a78b3a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The ASM stub invoked by irq_offload() wasn't switching to the
interrupt stack.
Change-Id: I0c52092a50396aa892e71f0501bbda38395d7554
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Making pipe driver configuration for quark_se makes no sense for the
board. First it simply wrong since IRQs for serial are 5 and 6 and
when using PIPE care should be taken to allocate right way serial and
Bluetooth for the given UARTs.
Change-Id: I4cb3227a8be34fbfa089a457e6d9977e4adcfd19
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
QUARK_SE_IPM_CONSOLE_RING_BUF_SIZE32 symbol must be editable through
configuration menus and configuration snippets (QA request).
Adding a title for the kconfig symbol makes it editable.
Change-Id: Id0147a50d94033e1392327935bcbfbdb5a9eedd8
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This driver uses the QMSI library and mostly translates calls from the
Zephyr API to QMSI ones.
This driver conflicts with the native driver implemenation. In order to
enable it, you must set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="PATH_TO_QMSI"
CONFIG_SPI_QMSI=y
CONFIG_SPI_QMSI_PORT_0=y
CONFIG_SPI_QMSI_PORT_1=y
Missing:
- Support for using a GPIO pin as Chip Select;
Change-Id: I0d8eca88a2a803b6b3604f396f874313fe90753c
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Decisions on compiler optimizations were done on the architecture level,
this does not scale and some SoCs will have different optimization levels
or compiler options needed. Moving this to the SoC makes it easy to optimize
differently when using the same CPU which we use to set the right optimization
now on the architecture level.
For IAMCU platforms, use the right architecture and tuning.
-march=lakemont -mtune=lakemont -miamcu -msoft-float
Change-Id: I458afca5feb9be5de8dcae559d6dcac3c6d6a2a7
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
