This fixes coverity CID 171565 which may be valid in case of the
connection is not properly setup, or its memory is corrupted, it
may cause use of invalid addresses to be set using
net_if_set_link_addr.
JIRA: ZEP-2344
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the TCP data packet needs to be re-sent after the packet is lost,
then the acknowledgment number will be changed. This then means that
the TCP checksum needs to be recalculated too.
Signed-off-by: june li <junelizh@foxmail.com>
The controller and host-side RX threads recently had their priorities
lowered to 8. Make the driver RX threads consistent with this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch splits out the application data and bss from the
rest of the kernel. Choosing CONFIG_APPLICATION_MEMORY will
result in the application and kernel being split.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Configure I2C using DT for the following STM32 boards:
disco_l475_iot1
nucleo_f401re
96b_carbon
olimexino_stm32
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The SAM4S, SAM3X, SAME70 all use the uart_sam.c serial
driver. This patch puts the configuration in DTS and
out of Kconfig. The SAME70 uses the USART as well.
USART DTS support for the SAME70 is also in this patch.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
The I2C Slave Read support isn't well defined and not actually supported
by any i2c driver at this point. We can add this back when slave mode
is more thought out.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Right now keep it simple for testing, we can decide how we want to go
forward with this vs MAINTAINERs file, etc.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If the depends_on has more than one item we need to match all of those
dependencies in the supported list.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When a node receives consistent DIO messages with same data from
Border Router just ignore those messages. Need not to proceed
further.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Link metric is part IPv6 neighbour data struct. But RPL code is
trying to access it from RPL parent table where link metric doesn't
exist. So provided an api to get IPv6 neighbour data from RPL parent
data.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
DAG rank will be properly written with net_pkt_write_be16() in
network packet. API will take care of endianness. So need
not to convert it using htons().
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Sender rank (16 bit uint) was properly read with net_frag_read_be16()
api and need not to convert it again using ntohs().
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Initialize the buffer to 0 and read one byte less than the
buffer size. The result should be that the last byte of
the buffer always stays 0. This way it is possible to verify
it the driver does not write outside the buffer.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Add a STM32 LL based driver for the RNG processor. The RNG processor
is a random number generator, based on a continuous analog noise, that
provides a random 32-bit value to the host when read. The RNG passed
the FIPS PUB 140-2 (2001 October 10) tests with a success ratio of 99%.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
We had various asserts when checking network packet length but
printed also error when there was none. Fix this by checking
do we really have a too short message.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove NET_TCP_HDR() macro as we cannot safely access TCP header
via it if the network packet header spans over multiple net_buf
fragments.
Fixed also the TCP unit tests so that they pass correctly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove NET_UDP_HDR() macro as we cannot safely access UDP header
via it if the network packet header spans over multiple net_buf
fragments.
Fixed also the UDP unit tests so that they pass correctly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove NET_ICMP_HDR() macro as we cannot safely access ICMP header
via it if the network packet header spans over multiple net_buf
fragments.
Jira: ZEP-2306
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IPv6 HBH option PAD1 ext header was not parsed properly
as the code read one extra byte from the ext header. The
PAD1 length is only 1 byte.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add utility function that helps to figure out if the
protocol headers can be directly accessed when they fit one
net_buf fragment, or if they need to accessed using various
net_pkt helpers that know about reading data from two
different net_buf's.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of directly setting pointer to where to start to calculate
the various IP related checksums, use the net_frag_skip() to first
find out what is the fragment where the calculation should start.
This needs to be like this so that if the IP header + possible
extension are so long that they do not fit the first fragment,
we need to be prepared to look into second fragment.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The following error and warning is received when connecting
to certain central devices:
[bt] [ERR] hci_num_completed_packets: packets count mismatch
[bt] [WRN] bt_att_recv: Ignoring unexpected request
This could happen if Tx-ed packet is not added to pending
list before a num of completed packets event and/or new Rx
packet is received.
This is fixed by reducing the Rx thread priorities in the
Host and the Controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
net_context_unref() is protocol agnostic, after being un-referenced,
the same context might end up being used then for UDP,
if context->tcp is not reset to NULL, calling net_context_unref()
after this UDP usage will again try to release this TCP pointer
which might lead to random error.
Signed-off-by: june li <junelizh@foxmail.com>
The config file for KW40Z has the shell disabled, as available
SRAM memory is limitted to 16kB.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Add support for KW40Z in the KW41Z IEEE 802.15.4 driver as both chips
expose almost the same radio registers.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Add minimal interface for the KW40Z XCVR driver to match the one offered
in MCUX v2.2 by the KW41Z XCVR driver.
This is needed to reuse the KW41Z IEEE 802.15.4 driver on KW40Z.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Add and update makefiles in order to build either the KW41Z or KW40Z
XCVR driver based on soc name.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Update KW40Z files for building XCVR driver by adding the required
includes, removing unneeded ones and replacing OSA_EnterCritical/
OSA_ExitCritical with OSA_InterruptDisable/OSA_InterruptEnable.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Import from Kinetis SDK v1.3 MKW40Z4_extension.h and fsl_bitaccess.h
which are needed to build the XCVR driver for KW40Z.
Origin: NXP Kinetis KW40Z Connectivity Software
Maintained-by: External
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Import the KW40Z XCVR driver from Kinetis SDK v1.3, which is needed
to setup the radio on the hexiwear_kw40z board.
Origin: NXP Kinetis KW40Z Connectivity Software
Maintained-by: External
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
The chip seems to require a wait time before reading packet
data after the RX sequence done interrupt, as imidiate reading
of it will indicate a packet size of zero and cause the RX
sequence done to be continually retriggered.
In addition, the extra clearing of the interrupt flags can be
removed, as this is already done at the beginning of the isr.
Jira: ZEP-2278
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
The code in send_frag() depends on being able to allocate a new
pending tx contexts with 100% certainty. We must therefore notify
*all* connections instead of the current one in order to ensure that
there are free contexts available in free_tx.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In some cases the lladdr might not be set, currently this is
seen with RPL unit tests, in which case we must not access
the lladdr.
Jira: ZEP-2330
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there is no route to the neighbor, then do not try to delete
it because the route pointer is NULL.
Jira: ZEP-2329
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>