Pin number should be decremented by 8 if the pin
refers to the GPIOx_AFRH register.
Change-Id: I76e960f3b4adc3c2139ef5a88f15dbe98603228e
Signed-off-by: Adam Podogrocki <adam.podogrocki@rndity.com>
This commit brings code size optimization as suggested by Christer
Weinigel review during review of initial commit for this driver.
It also cleans up useless definition in header file.
Change-Id: Ibeaa2e51570dff21825c60c30ba83d939b31d938
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After activation of cube based driver support on L4 and F3 series,
this commits performs the clean up of F3 and L4 relative code to
native clock control drivers.
Indirectly, it makes pwm driver supported de facto on F3 series
Change-Id: Idac17103a9b5ef6eab540719343cc8f5865f15fa
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introduction and activation of STM32Cube LL based driver on
F3 and L4 series, this commit removes the no more needed code for
native driver for these soc.
Change-Id: I266d1a3fc4b464cee34b1cc1a1a333c5bf923e41
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following activation of Cube LL based clock control driver,
this commits cleans up the useless structures for RCC definitions
and remove code relative to native F3 Clock control driver.
Change-Id: I6f3ee44adb09adc52927eb4b05f8a829665eb96d
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following activation of Cube LL based clock control driver,
this commits cleans up the useless structures for RCC definitions
and remove code relative to native L4 Clock control driver.
Change-Id: Ic0408d5f5ec66651d46d13dfaf447da2666367cd
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Activate support of LL Cube based Clock control driver
Note that prescaler should now use actual numerical value used
for calculation and not register value (hence 1 instead of 0)
Change-Id: Ia3a26bffbd470c6e958fd2ca82b8eb071beb6ca8
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Activate support of LL Cube based Clock control driver
Note that prescaler should now use actual numerical value used
for calculation and not register value (hence 1 instead of 0)
Change-Id: Ic2566d26f1b82441575a94ddd8d632c88df669d9
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Activate support of LL Cube based Clock control driver
Note that prescaler should now use actual numerical value used
for calculation and not register value (hence 1 instead of 0)
Change-Id: I4becae974678970745f918fb05906f36cc4d62a7
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introduction of STM32Cube based clock control driver for
stm32 family, provide its support on stm32f3x soc.
Clean up will have to be done afterwards.
Change-Id: I20480579f12a6fc1f1f6a51589981ac3f1d63ef0
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introduction of STM32Cube based clock control driver for
stm32 family, provide its support on stm32l4x soc.
Clean up will have to be done afterwards.
Change-Id: I979a4169148c5fe5a0693d182d2d17f9ffaf1c77
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update stm32f3xx flash driver to support it.
Clean up will be done afterwards.
Change-Id: I3260bb063f714fa29adbc71d8036f20479a99b34
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update stm32 pwm driver to support it.
Once supported across the whole family, a clean up will be done.
Change-Id: I2ed38763b706e34ea1dceea50e97ce836dd9e195
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update stm32 i2c_lx driver to support it.
Clean up will be done in a following commit.
Change-Id: Ie5059bf4122d65fab1a663a5b00e0d761850a49d
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use of SECONDARY in DEVICE_AND_API_INIT is now deprecated and should
be replaced by POST_KERNEL
Change-Id: I543ae70e493527e75b4a4bcb9191475065b49166
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update stm32 serial driver to support it.
Once supported across the whole family, a clean up will be done.
Change-Id: I7100bc699e7918c8be71d58091da1860ab734e25
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update pinmux driver to support it.
Once supported across the whole family, a clean up will be done.
Change-Id: Icc20816377f3a09f516a743462c92696a1fead3a
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update GPIO driver to support it.
Once supported across the whole family, we clean up will be done.
Change-Id: If50cb580cb01dc1d38557e54f19a8260feaa504e
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This new clock control driver aims at providing a lightweight
generic driver to the whole stm32 family.
Driver is based on LL Cube API and hence is for now available
only for STM32 supporting this API: stm32f3xx and stm32l4xx.
Other families should be supported soon.
Once globally supported, this unique driver will also help
reducing the impact of stm32 clock control heterogeneity in
other drivers.
Change-Id: Id15a8d0d44f03809b2907ef10d6877700459e674
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
List container changes apparently were merged in the wrong order causing
leaving it with a compilation error.
Change-Id: Ib9d9502ddb39330c262e495a33592d0340713d83
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch adds the base DTS support for the KW41Z Freedom board. The
initial set of changes include SRAM, FLASH, IRQ controller and LPUART
support.
Change-Id: Ic68c4959ddad0c5cfe70d5576a0e58372b93ec9d
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
This patch adds DTS support to the ARM CMSDK UART driver. The DTS
currently specifies the IRQ, IRQ PRIO, and base address of the port.
Change-Id: I8e5bc81c013958be4297d563495bf126b53a83a9
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the base DTS support for the V2M Beetle board. The
initial set of changes include SRAM, FLASH, and IRQ controller support.
Change-Id: I06685622b9c57ac358544c71350074ce06e3371e
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds device tree support to the STM32 UART driver. The base
address, interrupt, and interrupt priority values can now come from DTS.
Change-Id: I3c383da8b200037601ecb2dc087f99ef103761bb
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds all the necessary changes to enable use of DTS for
generating required build information.
Change-Id: Ia476fbb14c7d9d6b9db3340c73f599556a880da3
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the base DTS and yaml files required to support DTS
for the STM32L476 based Nucleo board.
Change-Id: Ic606a895a25f27d2990f651d0f3c3c5d84818cfd
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch ifdef's out information that would be redefined by
information generated from DTS. This patch also fixes up the serial
drives to work properly with the DTS generated information.
Change-Id: I912ccf35be23c107705a4866e5a68b3b51154ffa
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the necessary DTS, YAML, and Makefile changes necessary
to generate proper include information for the CC3200. The initial
base support includes SRAM, FLASH, and UART devices.
Change-Id: I8ef8c24c3915198dbb5cfeb2431aa6dc68267d0e
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds DTS support for the Hexiwear K64 platform. This
includes enabling the DTS config option and adding conditionals around
the options to be replaced.
In addition, a DTS file is provided that customizes the Kinetis
platform to match the hexiwear board. A fixup file is provided to map
the generated information to the current client driver usage. This
file is temporary.
Change-Id: I247d538c6e13e0d1d4141fee74046575a7d2972e
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds DTS support for the FRDM_K64F board. The defconfig
enables the DTS usage and the FRDM K64F specific DTS file provides the
differences from the base Kinetis DTS definitions.
A fixup file is provided to map the generated configuration information
to the driver consumers. The fixup file will be removed once the
drivers are modified to handle the newly generated information.
Change-Id: Ib0ada28faff6a30e8b40eba5c5853e9018ae5fcb
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds DTS support and related files for the NXP Kinetis
platform. The DTS files contain the base definitions for the hardware
nodes on Kinetis platforms. The YAML files provide the definitions of
the contents of the DTS nodes.
The Kconfig changes were put in place to allow for the conversion of
existing drivers. Once those drivers are modified, the Kconfig options
that are replaced by the DTS information will be removed.
Change-Id: If110fffa99c0b12471cf2df206da6687277e4756
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the base DTS and YAML files that may be referenced by
SoCs. The device tree files provide base definitions for the more well
known ARMV7M device nodes. These files are meant to be included in
SoC vendor specific device tree files.
The YAML files provide definitions for the contents of device tree node
that contain information that will be parsed and used for configuration
in the system.
DTS files define hardware and software configuration and YAML files
provide the markers for knowing which pieces need to be extracted.
Change-Id: I7e90fe19f09afb269b7b2988c2c19c0f26d7ee7c
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support for using device tree configuration files for
configuring ARM platforms.
In this patch, only the FLASH_SIZE, SRAM_SIZE, NUM_IRQS, and
NUM_IRQ_PRIO_BITS were removed from the Kconfig options. A minimal set
of options were removed so that it would be easier to work through the
plumbing of the build system.
It should be noted that the host system must provide access to the
device tree compiler (DTC). The DTC can usually be installed on host
systems through distribution packages or by downloading and compiling
from https://git.kernel.org/pub/scm/utils/dtc/dtc.git
This patch also requires the Python yaml package.
This change implements parts of each of the following Jira:
ZEP-1304
ZEP-1305
ZEP-1306
ZEP-1307
ZEP-1589
Change-Id: If1403801e19d9d85031401b55308935dadf8c9d8
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This commit removes unnecessary CONFIG_SYS_POWER_DEEP_SLEEP protection
in shim drivers as QMSI 1.4 has introduced empty context save/restore
functions that can be called in Quark D2000, therefore keeping common
code at the shim driver level for Quark SE and D2000.
Change-Id: Ia2a466327f999668c6511c0193014e9151bff6ae
Signed-off-by: Juan Solano <juanx.solano.menacho@intel.com>
While iterating on each node element it is much more common to try to
access the container struct which up until now have been done manually
using CONTAINER_OF macro, so this introduce CONTAINER variants that allow
to iterate directly with container pointer rather than the list node.
Change-Id: Ie1e0da948cb9517c3c5cd8e86b59b95d7d027bfa
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
