The REGION bits (bit[3:0]) of MPU_RBAR register can specify the number
of the region to update if the VALID bit (bit[4]) is also set.
If the bit[3:0] of "region_addr" are not zero, might cause to update
unexpected region. This could happen since we might not declare stack
memory with specific alignment.
This patch will mask the bit[4:0] of "region_addr" to prevent updating
unexpected region.
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
When checking for line length limits, ignore lines with Signed-off-by.
Some developers have a long name that would not fit within the limits.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
When src and dst addresses are compressed based on context
information, uncompression method should verify CID bit,
SAC and DAC bits and context ID's. But it has missed some
cases which resulted in invalid uncompressed IPv6 header.
e.g. CID is set, SAC is 0 and DAC is 1 and context id's provided.
Uncompression method assumed that src address is compressed based
on context information but it is not.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Empty RPL HBH header will be inserted while finalizing IPv6 packet
but updated after finding nexthop and sent the packet. In case of
Bluetooth or multicast dst address it was missed. Resulted in
empty RPL HBH header and packet dropped at peer node. It should
be updated in all circumstances.
Jira: ZEP-2088
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The mbedtls debugging function was set before the ssl config
struct was initialized. This meant that it was not possible
to activate mbedtls debug prints. This commit sets the debug
print option after the config struct has been initialized.
Fixed also the debug prints which print extra \n which looks
very bad in debugging outputs.
This commit does not enable mbedtls debugging, it just makes it
possible to output mbedtls debug prints. In order to get mbedlts
debug prints one needs to do this:
* set DEBUG_THRESHOLD to >0 in http_server.c
* enable CONFIG_NET_DEBUG_HTTP in project config file
* enable MBEDTLS_DEBUG_C in mbedtls config file (see file pointed
by CONFIG_MBEDTLS_CFG_FILE option)
* in qemu, one needs to increase the size of the available RAM,
this setting does the trick, CONFIG_RAM_SIZE=300
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Refactor internals of IPM driver removing bitfields and byte access of
32 bit registers.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The current method of accessing 32-bit data and control registers does
not work for all quark architectures. Sometimes writing to those
registers byte-by-byte results in last byte occupying whole 32 bit
register.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Move all characters to "char" type: no implicit conversions between
"unsigned char", "u8_t", etc.
Tested with ISSM 2016.2.085.
Jira: ZEP-2159
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Semantics of ENOENT error as used previously is "named entity not
found", whereas for "I/O handle is not valid", there's EBADF. For
example, POSIX/SUSV2 doesn't even list ENOENT as a possible error
for accept(), connect(), recv(), etc. whereas it lists EBADF, e.g.:
http://pubs.opengroup.org/onlinepubs/7908799/xns/connect.html
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add a repeat param to gatt-write-without-response so that
it covers what gatt-write-without-response-repeated was
doing. gatt-write-without-response was removed in the
commit 26eae70da.
gatt-write-signed too will have repeat param with this
change.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add clarification that the DNS server configuration must be edited in
the respective prj.conf file.
JIRA: ZEP-2040
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Inserting the IDT results in any data afterwards being shifted.
We want the memory addresses between the zephyr_prebuilt.elf
and zephyr.elf to be as close as possible. Insert some dummy
data in the linker script the same size as the gen_idt data
structures. Needed for forthcoming patches which generate MMU
page tables at build time.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Having tried and tested building Zephyr using the standard SDK on
Windows 10 using the new WSL (Windows Subsystem for Linux), add the
documentation so that others can benefit from the functionality.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This patch adds a YAML template file that describes the format of a
Zephyr device tree YAML specification.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds documention for device tree development in Zephyr. This
includes a description of device tree, how it is integrated into Zephyr,
and other related information.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
At the moment all bluetooth logs are prefixed with [bt] making it
difficult to understand where the logs belong to.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The kernel tracks time slice usage with the _time_slice_elapsed global.
Every time the timer interrupt goes off and the timer driver calls
_nano_sys_clock_tick_announce() with the elapsed time, this is added to
_time_slice_elapsed. If it exceeds the total time slice, the thread is
moved to the back of the queue for that priority level and
_time_slice_elapsed is reset to zero.
In a non-tickless kernel, this is the only time _time_slice_elapsed is
reset. If a thread uses up a partial time slice, and then cooperatively
switches to another thread, the next thread will inherit the remaining
time slice, causing it not to be able to run as long as it ought to.
There does exist code to properly reset the elapsed count, but it was
only compiled in a tickless kernel. Now it is built any time
CONFIG_TIMESLICING is enabled.
Issue: ZEP-2107
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The STM32F412 has PWM output capabilities. Add support to the blink_led
samples.
Tested using a Nucleo STM32F412ZG board (PWM output on pin 28 of the
CN11 Morpho connector and pin 29 of the CN10 Zio connector).
Change-Id: I75fb986fa97bd1c07c6375938430e7963297cd9d
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Add necessary board files, pinmux and device tree in order to have a
usable debug console.
Origin: Original
Change-Id: I43a9d278c3f2c936a714263626722f630367b663
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Add necessary Kconfig and minimal device tree in order to support
STM32F412ZG variant as found on the Nucleo STM32F412 board.
Origin: Original
Change-Id: Ic98a686f478ce551dc6101466ed0cf16924109e8
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Following migration of stm32f1xx series clock control driver to
STM32Cube LL API, cleanup stm32 code base in order to take into
account that this is the only clock driver available for stm32
family.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following introduction of stm32cube LL based clock control driver,
remove references to former native driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following introduction of stm32cube LL based clock control driver
for stm32f1 series, update stm32f1xx based boards to support new
driver settings
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Before introduction of LL based clock control for stm32f1xx series,
prepare gpio driver to provide useful definition for new API
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Align stm32f1xx series clock driver to other parts of stm32 family.
Driver support both Connectivity and Density lines of stm32f1 series,
that are based on different Reset and Clock Control architectures.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The STM32F413 has PWM output capabilities. Add support to the blink_led
samples.
Tested using a Nucleo STM32F413ZH board (PWM output on pin 28 of the
CN11 Morpho connector and pin 29 of the CN10 Zio connector).
Change-Id: I3b25b09cab54265b28088ac9681aec588d9d48b5
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The Nucleo STM32F413 board is missing the default pinmux for PWM2 on
PA0, as stated in the doc. The same pinmux is also done for other
similar Nucleo board. So add it!
Change-Id: I2086c0a4ce65d68455a0978570f118e965f4c6ca
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Enable the MPU on the Nucleo STM32F413 board.
Change-Id: I0f256a4c7231f9d3844e67a94d989c8d93b60e58
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The STM32F413ZH has 1536kB of Flash and 320kB of SRAM. This
configuration is currently not supported by ST MPU driver, so fill in
the blanks.
Note: The MPU does not support region size that is not a power-of-2 (see
the SIZE field in the MPU_RASR register). This is a problem for our
1536kB Flash region, so it was rounded up to the nearest choice. This is
possible because the memory in the range 0x0818000 - 0x0FFFFFFF is
"Reserved" and thus not mapped anyway.
Change-Id: If0c3d1db564ca45e77f8b5bafa2afdbafa85b40f
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
CONFIG_CLOCK_VDD_VOLTAGE does not exist. It was introduced by accident
with commit 614db02cc6 ("stm32f4: Add STM32F413 Nucleo board"), so
remove it!
Change-Id: I3363a92627708bf5ffb080c2238fc84c71caa8d9
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Atmel SAM3X series has been recently converted to use ASF
and should now use common SAM family drivers. The atmel_sam3
serial driver will be removed in the future.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Instead of waiting forever for a free net_buf, set a timeout to
the allocations (500 ms). This way the application will not be
blocked by memory exhaustion.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In some cases the net_pkt can be null when freeing it,
this will print error from net_pkt library. Avoid this by
checking the value of net_pkt before calling net_pkt_unref().
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we re-connect to same peer server, then we should select a new
source port. Noticed that if the same source port as before is
used for the new connection, the peer might drop the packet. This
was seen when connecting to Linux peer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The number of RX and TX buffers is increased to 64 as the
earlier limit can cause memory exhaust in some cases.
Jira: ZEP-2223
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Defines a new tunable, CONFIG_NET_TCP_RETRY_COUNT, that determines the
number of segment retransmissions that the IP stack will attempt to
perform before resetting the connection.
The default value is 9 retransmissions, which amounts to 1:42 minutes,
as close as possible to the minimum recommended by RFC1122.
Jira: ZEP-1956, ZEP-1957
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This fix is basically a no-op as the rx_buf pointer cannot be null
in practice, but in order to avoid Coverity complaining about
it add some null pointer checks to the UDP handling code.
Coverity-CID: 170124
Jira: ZEP-2235
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Calling 'svc' on ARMv6 causes a hard fault if interrups are locked.
Force them unlocked before making the svc call.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
