Fixed AF for USART 6 on PC6/PC7 PG8/PG9/PG12/PG13/PG14/PG15
All RTS/CTS/RX/TX pins now have correct AF7 instead of wrong AF8.
Signed-off-by: Jeremy LOCHE <lochejeremy@gmail.com>
All pinmux supporting CAN, SPI and I2C of F7 series are added.
Since the F7 series supports up to two CANs,
the pin names of CANs have been changed.
Several minor pinmux errors have also been fixed.
Sorted by Alternate function.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
The STM32L072CZ MCU has a built-in USB device controller which is
supported by Zephyr's USB STM32 driver. The b_l072z_lrwan1 board has a
micro-USB connector that is wired to the MCU via two solder bridges
(SB15 and SB16) that need to be closed to connect the data lines.
Update the board documentation to describe the solder bridges and
enable the USB controller in the device tree.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Changes:
- Added all required board files in /boards/arm/96b_aerocore2
- Modified pinmux for stm32f4
Most of the changes in this PR is based on reverse-engineering of the
PCB layout and following commits in the PX4 firmware repository for
the same board. The manufacturer does not provide and or generate
schematics and pinout tables for this board.
This PR includes almost all of the interfaces connected to the STM32
MCU, the only thing not included is the J9 and J8 headers that connect
to a 96Boards baseboard.
These headers are not vital to the functionality of the Aerocore2.
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Update dtsi and pinmux macros for stm32f7 family. Add sdmmc1 to dts file
for stm32f746g_disco. Also add board specific configuration file for
fat_fs sample.
Signed-off-by: Helge Juul <helge@fastmail.com>
Update the dtsi for stm32l471 (which the higher SoCs are based on) to
support the stm32-sdmmc disk access device. Enable the device for the
stm32l496g_disco board, and update the pinmuxing.
Note that the stm32l496g_disco board also has a card detect gpio
(MFX_GPIO8), but this is not supported yet. When not specified the
driver will assume a card is present.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Add support for ADC on H7 series. Note that ADC1 and ADC2 share the same
register set, so it is added as "adc1_2".
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Like stm32 L4 does,
when the STM32WBx SoC goes into STOP mode, the SPI device is disabled.
This cause the pins to not be drived anymore (i.e. they are floating)
except through their pull-up or pull-down.
From the logical point of view, the NSS pin is held high by a pull-up
so it's not a problem if the other pins are floating. However those pins
are floating input for the slaves, which increase their power
consumption.
The solution is to hold the state of the pins through a pull-up or a
pull-down. This is already done for the NSS and MOSI pins, but not for
SCK. Fix that by using pull-down on the SCK pin the same way it is
already done for the MOSI pin.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Remove semicolon between instance invocations of DT_FOREACH_IMPL_ and
thus DT_INST_FOREACH. This provides more flexibility to the user. This
requires we fixup in tree users to add semicolon where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
* Define USB driver for base stm32wb device.
* Enable USB for the nucleo_wb55rg board.
* Properly initialize USB power + clock for the platform.
Signed-off-by: Pete Johanson <peter@peterjohanson.com>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix some wrong assignments for SPI2 and add all other alternative
functions for USART, I2C, SPI and CAN according to STM32F091VC
datasheet, which is at the top end of this series.
https://www.st.com/resource/en/datasheet/stm32f091vc.pdf
Signed-off-by: Martin Jäger <martin@libre.solar>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert pinmux driver to use nodelabels to get references to devicetree
nodes using the new devicetree.h macros.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add I2C1 SDA/SCL configuration on pins PA9 and PA10, as they are
currently only available on other pins.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Convert driver to use new DT_INST macros throughout. This allows us to
also remove dts_fixup.h that are no longer used.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When the STM32L4x SoC goes into STOP mode, the SPI device is disabled.
This cause the pins to not be drived anymore (i.e. they are floating)
except through their pull-up or pull-down.
From the logical point of view, the NSS pin is held high by a pull-up
so it's not a problem if the other pins are floating. However those pins
are floating input for the slaves, which increase their power
consumption.
The solution is to hold the state of the pins through a pull-up or a
pull-down. This is already done for the NSS and MOSI pins, but not for
SCK. Fix that by using pull-down on the SCK pin the same way it is
already done for the MOSI pin.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Most of the MISO and MOSI SPI pins of STM32L4 SoCs are configured with
a pull-down except PE14 and PE15. Change them for consistency.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Updated the openisa,rv32m1_vega-pinmux binding to require the label
property and updated the rv32m1.dtsi to add label properties for the
pinmux nodes.
Also update gpio_basic_api test to use DT_NODELABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in esp32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
LPUART1 TX alternate function number for PB6 was not correct in the
pinmux settings for H7 series.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This patch is setting the pin to very high speed for all
the SPI2 clock outputs, for the stm32f7 soc series.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
I think people might be reading differences into 'if' and 'depends on'
that aren't there, like maybe 'if' being needed to "hide" a symbol,
while 'depends on' just adds a dependency.
There are no differences between 'if' and 'depends on'. 'if' is just a
shorthand for 'depends on'. They work the same when it comes to creating
implicit menus too.
The way symbols get "hidden" is through their dependencies not being
satisfied ('if'/'depends on' get copied up as a dependency on the
prompt).
Since 'if' and 'depends on' are the same, an 'if' with just a single
symbol in it can be replaced with a 'depends on'. IMO, it's best to
avoid 'if' there as a style choice too, because it confuses people into
thinking there's deep Kconfig magic going on that requires 'if'.
Going for 'depends on' can also remove some nested 'if's, which
generates nicer symbol information and docs, because nested 'if's really
are so simple/dumb that they just add the dependencies from both 'if's
to all symbols within.
Replace a bunch of single-symbol 'if's with 'depends on' to despam the
Kconfig files a bit and make it clearer how things work. Also do some
other minor related dependency refactoring.
The replacement isn't complete. Will fix up the rest later. Splitting it
a bit to make it more manageable.
(Everything above is true for choices, menus, and comments as well.)
Detected by tweaking the Kconfiglib parsing code. It's impossible to
detect after parsing, because 'if' turns into 'depends on'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The SoC, driver, and board support for the CC2650 and CC2650 Sensortag
aren't currently supported and we are removing them as such. If anyone
is interesting in supporting this platform we can easily recovery it
from git.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Ensure that the SPI SCK and MOSI pins are set to very high as slower
SPI speeds will cause device hangs when used. This is due to the state
changing too fast for hardware, causing RXE to never fire and thus
hang.
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
Add support for the ST STM32G0316-DISCO development board. This board
features an ST STM32G031J6 MCU on a breakable SO8 to DIL8 module, a user
LED and a button.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>