Make sure that when e.g. CONFIG_SERIAL is set, CONFIG_UART_SAM0 is
selected automatically when the sam0 SoC family is used.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
This commit adds CAN support for nucleo F746zg.
Furtermore CAN was added in stm32f7.dtsi and pinmuc_stm32f7.h
CAN_RX: PD0, CAN_TX: PD1
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Reformat L4 pinmux to be consistent with other pinmux files,
and for a better reading.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Maybe this is some "just in case" thing that got copied around. There's
no need to have a blank line at the beginning or end of Kconfig files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Most of these are from source'ing a file within an 'if PINMUX', and then
adding another 'depends on PINMUX' within it.
'if FOO' is just shorthand for adding 'depends on FOO' to each item
within the 'if'. There are no "conditional includes" in Kconfig, so
'if FOO' has no special meaning around a 'source'. Conditional includes
wouldn't be possible, because an 'if' condition could include (directly
or indirectly) forward references to symbols not defined yet.
Tip: When adding a symbol, check its dependencies in the menuconfig
('ninja menuconfig', then / to jump to the symbol). The menuconfig also
shows how the file with the symbol got included, so if you see
duplicated dependencies, it's easy to hunt down where they come from.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Converts the rv32m1 pinmux driver to use 'DT_' prefixed defines instead
of deprecated non-prefixed defines.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fix issue #9028: last bit of SPI/I2S transaction may be corrupted.
Impacted STM32 SOC series: F0/F1/F2/F3/F4/L0.
Notes:
- F2/F4/L0: set gpio to very_high speed ('11')
- F0/F3: set gpio to high speed ('11').
- F1: set gpio to 50MHz.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
pinmux dev isn't really used or supported. We only have one driver that
is implmeneted, and that driver isn't ever enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added UART4 alternate pin function for L4 µC for PC10 and PC11.
Corrected naming of previously defined UART4 TX and RX defines.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Supported PWM at pins A0, D3, D5 and D6 which are also Arduino
compatible. Also the onboard red LED can be used with PWM.
The basic/{fade_led, blink_led} samples to apply to this board
seemlessly and operate on the onboard red LED.
Also supported RTC.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
Clean up a left over from GPIO driver factorization.
Definition of GPIO_REG_SIZE and GPIO_PORTS_BASE do not need anymore
to be spread accross SoCs.
Put these definitions directly in STM32 pinmux driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
All series STM32 have mostly the same GPIO architecture
and can share the same code for GPIO manipulation.
Functions of the external interrupt line control are also the same.
This patch extracts common code from them and put them into the 'common'
folder.
Functions of control GPIO of these series scattered in
soc/arm/st_stm32/stm32xx/ folders contain these functions:
stm32_gpio_flags_to_conf(), stm32_gpio_configure(), stm32_gpio_set(),
stm32_gpio_get, stm32_gpio_enable_int().
This patch merges them into the gpio_stm32.c file.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
The i2c_atmel_sam3 driver was deprecated at release 1.9, this commit
removes it. Also pinmux_dev_atmel_sam3x driver is removed.
i2c_atmel_sam3 was the last one which depended on it.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update a couple of labels generated from DTS used directly (not through
dts_fixups) in TI CC2650 system initialization code and a few drivers
for this SoC.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update stm32f469i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
-Update yaml file
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32f723e_disco configuration to match with
default configuration guidelines:
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32f769i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32l496g_disco configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update disco_l475_iot1 configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added support for SPI 1 available from the arduino connector (plus an
extra gpio). Tested against samples/sensor/bme280.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Add pin muxing for STM32F302x8 by sharing most of the definitions
of the STM32F303xC. Add USART3 for both the 302x8 and the 303xC.
Add a PWM that is specific to the 302x8.
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Group the entries by pin number and then sort them by alternate
function. This helps when editing the file.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The drivers/pinmux/dev directory doesn't containe any CMakeLists.txt
file, preventing to enable the PINMUX_DEV option. Fix that by providing
one.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
FE310 is the name of one SoC out of a range of products in the SiFive
Freedom line. The FE310 SoC port in Zephyr is compatible with all of
these products, so rename the SoC to SiFive Freedom
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Add support for usbotg_fs, by adding the DT fixup, pinmux macros,
and the DT entries in stm32f2.dtsi.
Signed-off-by: Istvan Bisz <istvan.bisz@t-online.hu>
This patch adds support for Ethernet in the STM32F2 family of
microcontrollers and enables it for the the Nucleo-F207ZG.
Signed-off-by: Daniel Egger <daniel@eggers-club.de>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
ports_enable array holds port clock information.
It is populated for all SoCs, but ports availability depends on
SoCs. The way it is defined today, location of the port in the
array depends on previous ports definition in SoC CMSIS files.
Though, port index is always the same irrespective of previous
ports availability in the SoC.
This will result in incoherency between port index and clock
information.
Fix this by setting a bogus value if port is not defined.
Return an error if bogus value is read.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The STM32F7 uses the V2 version of the STM32 I2C controller. Add the
corresponding Kconfig, DTS, DTS fixup and pinmux entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The STM32F7 uses the same USB OTG FS controller than the STM32F4 series.
It is therefore trivial to add support for it, by adding the DT fixup
and pinmux macros, and the DT entries in stm32f7.dtsi. Keep it disabled,
it should be enabled at the board level.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Define the pinmuxing for I2Sx_CK, I2Sx_SD and I2Sx_WS wires (with
'x' in the range 1 to 5). The multiplexing has been selected in
accordance to the ArgonKey board requirements.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The patch adds serial driver support for STM32F7 family
microcontrollers, includes pinmux definitions and DTS fixup file.
Signed-off-by: Yurii Hamann <yurii@hamann.site>
This commit enables CAN on the STM32L432.
Tested on nucleo l432ck with external transceiver and loopback mode.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
The nucleo_f334r8 uses STM32F3_PINMUX_FUNC_PA8_PWM1_CH1 inside its
pinmux but it is not defined anywhere.
Add the definition into the pinmux file to fix the build of
nucleo_f334r8 when enabling CONFIG_PWM.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
Enable supporting UART4 on STM32F107 and STM32F103Xe SoCs.
Modified stm32f1/dts.fixup for replacing USART with UART.
Signed-off-by: Jun Li <jun.r.li@intel.com>
There is no pinmux_dw.c and not Kconfig symbols associated with
CONFIG_PINMUX_DW, so remove the references to them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The pinmux subsystem does not have any API documenation. Currently
none of the existing pinmux drivers do any kind of input validation
for the pin/op parameters, which has been shown to allow the caller
to access unauthorized memory, up to and including disabling the
MPU.
This requires a proper specification for the pinmux subsystem and
also modification of existingd drivers to validate arguments on a per
driver basis. Remove user mode access until #7390 is resolved.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Driver APIs might not implement all operations, making it possible for
a user thread to get the kernel to execute a function at 0x00000000.
Perform runtime checks in all the driver handlers, checking if they're
capable of performing the requested operation.
Fixes#6907.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
We have been combining imported mcux drivers into a flattened directory
structure to maximize driver reuse, but the introduction of additional
nxp soc families (lpc and imx) to zephyr has introduced driver naming
conflicts. This caused us to rename and modify imported files, such as
fsl_gpio.c/h, to make them unique across all three nxp soc families.
This makes updating the the mcux drivers complicated, especially for the
lpc family.
Reoganize the mcux drivers into soc family subfolders, so we can just
copy all the drivers from an mcux distribution (which is done on an
soc-basis) into the appropriate soc family folder. Undo all of the
naming changes that occurred when lpc and imx drivers were originally
imported. Undo the accidental squashing of the kinetis watchdog and dcdc
drivers that occurred when the imx drivers were introduced.
The drawback to this approach is that we have duplicate files when the
same hw ip modules exist in multiple soc families, however there are
only few cases where this occurs, such as fsl_lpuart and fsl_trng.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Since PINMUX_INPUT_ENABLED == 1 and PINMUX_OUTPUT_ENABLED == 0,
we can not set a gpio port as input and output at the same time,
So we always set the gpio as input. Thus, the gpio can be used on
I2C drivers for example.
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
Pin multiplexing is a function of the PORT peripheral. This change
defines a separate pinmux device at the same address as the PORTs
themselves.
Signed-off-by: Michael Hope <mlhx@google.com>
Adds pinmux defines to use I2C2 at PB10/PB11 for
stm32f0-based boards.
Needed for stm32f072b_disco board to use extension
connector
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
Adds a new pinmux driver for lpcxpresso54114 based on mcux.
Signed-off-by: Shiksha Patel <shiksha.patel@nxp.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
On stm32f3_disco pins PF0/PF1 are used for OSC_IN/OSC_OUT
signals. Use pins PA9/PA10 for I2C_2 port
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
pinmux_pin_get() needs memory validated for the func parameter since
it's a pointer that gets written to.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
checkpatch returns the following errors:
"ERROR:COMPLEX_MACRO: Macros with complex values
should be enclosed in parentheses"
Let's fix all of them.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Add pinmux configuration for USB OTG Full Speed.
Ports 11 and 12 use alternate function 10 for DM/DP.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Default configuration for USART1 (Console output) on board
stm32f3_disco was set on PA9/PA10, which matches Rev-A/B
configuration. Though, on more recent configuration of the
board (Rev-C onward). USART1 is mapped to PC4/PC5.
This configuration has the benefit to support VCP, hence it
is chosen to be set by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add SPI3 pin definitions for PC10, PC11, PC12.
This is required to use SPI3 on disco_l475_iot1 board
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move all STM32 based board pinmux files into the board dirs so we are
consistent across all the STM32 platforms/boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Esp-idf defines the BIT macro that is also defined in Zephyr's
misc/util.h. Fix the issue by including the esp-idf headers first, so
that a check in util.h won't redefine the macro if it's already
defined.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This implements a driver for the pin multiplexer as present in the ESP32
SoCs.
All APIs are supported.
Jira: ZEP-2297
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Add SPI pin mux tables for 96b_carbon. Note that SPI1 is for
internal use on the board connecting to the 96b_carbon_nrf51, while
SPI2 is broken out to an expansion header.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Following rework of pinmux driver for whole stm32 family,
remove call to stm32_get_pin_config which is no more
used.
Include dt-bindings stm32-pinctrl.h file to ensure coherency
between dts files and pinmux driver.
Due to change of "port" from enum to a series of define
(enum not accepted as dt binding), rework gpio_stm32_config
declaration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32F3 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32F4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rework stm32f1 pinmux code for future dts based pinmux code
generation.
Pin configuration is now done directly thanks to gpio port
configuration. Reference to pseudo alternate functions are
now removed same as the use of pins[] array.
Pins function (uart tx for instance) is set implicitly by
defining gpio mode and configuration.
This behavior is specific to stm32f10x series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32L4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed and information is transferred to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following implementation of LL based SPI driver,
add SPI support on nucleo_f334r8 board of STM32F3 series.
Change-Id: Ifbe39b1f2cecdd7db23be9c6943a914a155ebd77
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add SPI pin for the nucleo_f401re pinmux.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add configuration, documentation, pinmux, fixup and dts support for
STM32F103x8 based Minimum System Development board.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Add necessary board files, pinmux and device tree in order to have a
usable debug console.
Origin: Original
Change-Id: I43a9d278c3f2c936a714263626722f630367b663
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Following migration of stm32f1xx series clock control driver to
STM32Cube LL API, cleanup stm32 code base in order to take into
account that this is the only clock driver available for stm32
family.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The Nucleo STM32F413 board is missing the default pinmux for PWM2 on
PA0, as stated in the doc. The same pinmux is also done for other
similar Nucleo board. So add it!
Change-Id: I2086c0a4ce65d68455a0978570f118e965f4c6ca
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
This patch converts Atmel sam3x MCU series to use register
header files from Atmel Software Framework (ASF) library.
By using ASF different Atmel SAM MCU series can use common
device drivers.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add configuration, pinmux, dts and documentation for the STM32L496G
Discovery board based on the STM32L496AG SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add defines and pinmux arrays to support more UARTs on STM32F4.
Change-Id: Ib06c549bdb2b3d7065554a0a6d1a3d15441b29c9
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
