For now we've used range properties as a pass through. However range
properties can translate from one address space to another. This is
typically used one address spaces translate from one physical bus to
another (For example going from PCI address space to internal SoC memory
map). However, we can also use this for cases where we want to reduce
duplication (For example with ARMv8-M for secure v non-secure MMIO
registers).
'ranges' takes either the form of:
ranges; /* pass through translation */
or:
ranges = <child-bus-address parent-bus-address length>;
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix bluetooth config dependencies where the definitions depend on other
definitions.
BT_RX_PRIO is not always defined in a controller only build.
BT_CTLR_TX_BUFFER_SIZE does not depend on BT_CTLR, but BT_LL_SW.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Following log subsystem rework, a warning poped-up in SYS_LOG_ERR
in spi_stm32_get_err macro.
Fix it by casting SPI_STM32_ERR_MSK on (u32_t)
Fixes#10380
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We use to walk to the full tree in search of addr/size cells. We should
only have to look at the parent of the node for these properties.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Given the path address to a node return the address/size cells. In
theory this should just be looking up the #{address,size}-cells in
the parent node, we'll make that cleanup next.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This header is private data and we shouldn't (and aren't) using it in
the tracing_sysview.h. SystemView tracing works fine without it, as
tested with the philosophers sample.
This commit fixes the build when bluetooth SMP and SystemView tracing
are used, because the kernel_structs.h inclusion ends up pulling in
kernel_internal.h, which declares smp_init(), whose declaration
conflicts with another internal routine by the same name in
subsys/bluetooth/host/smp.c.
Signed-off-by: Marti Bolivar <marti@foundries.io>
The way uart console is setup for this is not compatible with the logger
and needs additional changes, excluding until we have this implemented
in a generic way.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
As the sample.yaml file was missing, then sanitychecker did
not testing any wifi drivers or other wifi related APIs.
Fixes#10389
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The wifi management interface was still using one SYS_LOG_DBG
macro call, replacing that with NET_DBG.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adding spaces around "=" when definining Kconfig template so
that is more consistent with overall style of these template
variables.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Calling bt_recv in the Bluetooth host Tx thread by the
controller implementation caused deadlock in combined host
controller builds when HCI LE Create Connection Cancel
generated the HCI LE Connection Complete or HCI LE Enhanced
Connection Complete events.
Controller's HCI implementation has been updated to place
the generated event into Rx FIFO to avoid the deadlock.
Relates to commit a59f544fb4 ("bluetooth: controller:
Handle non-priority events correctly")
Relates to #10314.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
bt_conn_disconnect removes device from autoconnect list and thus
should not be called from le_conn_update when timeouting pending
connection. Also auto connect flag needs to be check on connection
failure to make sure scan is restarted.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
In commit d5836195d7 ("Bluetooth: controller: Increase advertising
random delay resolution"), the resolution of random_delay was
increased from 8-bit to 16-bit. Due to this switch the result
of HAL_TICKER_US_TO_TICKS() can now be a 0, which causes the following
crash:
***** Kernel OOPS! *****
Current thread ID = 0x200043f0
Faulting instruction address = 0x17914
Fatal fault in ISR! Spinning...
Let's make sure we don't pass a 0 to ticker_update() by increasing
the result of HAL_TICKER_US_TO_TICKS() by 1.
Signed-off-by: Michael Scott <mike@foundries.io>
Added functionality to enable active shell backends via Kconfig
file. When there will be more backends implemented user will
have an option to select only required ones.
It is no longer needed to select SERIAL in prj.conf.
Fixes#10190
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Enhance semaphore test to validate sem_timedwait()
and sem_trywait(). This is intended to improve
code coverage.
Also modify ztest check with zassert_equal with
return value instead of zassert_false for better
understandability.
Signed-off-by: Spoorthi K <spoorthi.k@intel.com>
Some of the headers referenced in the pinmux.c file don't exist. Match
the includes that the lpcxpresso54114_m4 pinmux.c file uses.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In case of having more than one reg, aliases would not generate
properly. Number of register at the end of define was missing.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
The gpio controllers on SAM4S, SAME70, and SAMD were missing properties
related to GPIO pin generation. Add the missing details into the yaml
and dts files to allow boards to specific gpio pins.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the needed bits to get device tree support for the GPIO controller
on the Zedboard-Pulpino. This will allow us to move LED & button info
into the board.dts.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add simple device tree support for the Pulpino SoC and Zedboard-Pulpino
board port. This gets the UART info from device tree instead of soc.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Drop a few paths from when we preprocess the dts. This is to reduce
creep of where #defines might get resolved from.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The commit 8592501828
("net: Remove s_addr/s6_addr defines from in_addr/in6_addr")
did a (welcomed) removal of a #define s_addr for which the SimpleLink
SDK was checking, breaking the socket_offload driver build.
This patch fixes the driver to work with this new, better
s_addr symbol definition.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The builtin function __builtin_umul_overflow returns a boolean and
should not checked as an integer.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
As the debugging print calls are async, all the strings that might
be overwritten must use log_strdup() which will create a copy
of the printable string.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The application won't work anymore as it uses the old syslog
logging and networking is now converted to use the new logger
so there is no need for this sample application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The code was trying to print peer IP address string but that
pointer could contain garbage. There is actually no need to print
anything in this case, the error code return is enough.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add "openthread" tag for sanitychecker when it is running
OpenThread specific tests. This way it is easier to run just
those few OpenThread specific tests.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>