After startup ublox-sara-r4 code sets the MDM_POWER signal to input
using a deprecated configuration macro. This was the only use of the
modem context API to configure a pin.
Refactor the API to not take the flags as an input but instead select
between the flags to be used when the pin is active and a disconnected
state. Use this API instead of a separate direct configure call when
initializing the modem pins.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the non-deprecated flags and configure the modem power switch as
active-low. The UBLOX_PWR_DETECT signal appears to be active high.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Remove macros and a state structure that are not used anywhere and
incompletely describe a GPIO pin specifier.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Treat Kconfig-specific GPIOs as active-high (default) and use the
logic-level API to interact with them.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update the DRDYB pin interrupt handling code of the TI LMP90xxx ADC
driver to use the new GPIO API.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Update the lora/sx1276 driver to the new GPIO API, using configured
active level and the replacement interrupt and active-sensitive set
APIs.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Document and assign write-protect signal as active low, and use the
active-sensitive API to control it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Convert to the new GPIO API using logical access, including setting the
GPIO line as active low in the Device Tree source.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update bluetooth hcp_spi sample to new GPIO API.
Following changes have been done:
- Use new gpio api functions
- Introduce define for dt generated gpio flags
- Update 96b_carbon_nrf51.dts according to new bindings
- Gpio IRQ pin is configured to output inactive
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use new configuration API, replace callback enable/disable with
interrupt enable/disable, and set active level in devicetree source.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Conver to the new GPIO API using raw access, since the driver
has its own macros to define signal levels.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert to the new API using raw access, since it's a common access
layer shared by multiple (right now only ublox-sara-r4) modems.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert to the new GPIO API using logical levels, and remove the
duplicate implementation of LED control that existed.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the flags included in the new GPIO API to describe the properties of
LEDs and buttons in the device tree source files.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>