In case OPENTHREAD_NCP option is disabled, uart.c platform driver should
not be compiled as it misses dependencies.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
When NCP starts-up some of the initialisation functions of a regular
OpenThread device do not need to be called, because they get triggered
by wpantund via UART. Instead NCP initialisation needs to be called.
A small typo has been fixed as well.
Also initialisation for raw link packet interface has been added. Can be
used for picking up 802.15.4 frames and interpreting them in the
application.
Signed-off-by: Markus Becker <markus.becker@tridonic.com>
The functions ppp_mgmt_raise_carrier_on/off_event() were not
implemented, but already documeted in the header net/ppp.h
Fixes#23420
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
ieee802154_scan() checks if ctx->scan_ctx (scan) is NULL what implies
that this can be true, but de-reference this variable before this
check what may cause a problem.
Fixes#23299 [3]
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
If the network interface is down, we should timeout properly
and let the application to handle the situation.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It is possible that net_pkt will disappear while we are sending
it, so save link address if we need that information.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we are receiving UDP packet and if there is some error happening
inside zsock_recv_dgram(), then make sure that the net_pkt received
from recv_q is freed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The code was leaking memory in TX side when there was lot of
incoming packets. The reason was that the net_pkt_sent() flag
was manipulated in two threads which caused races. The solution
is to move the sent flag check only to tcp.c.
Fixes#23246
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The current design of the network-specific stack dumping APIs
is fundamentally unsafe. You cannot properly dump stack data
without information which is only available in the thread object.
In addition, this infrastructure is unnecessary. There is already
a core shell command which dumps stack information for all
active threads.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Contents of mqtt_3_1_0_proto_desc and mqtt_3_1_1_proto_desc were logged
with following code:
MQTT_TRC("Encoding Protocol Description. Str:%s Size:%08x.",
mqtt_proto_desc->utf8, mqtt_proto_desc->size);
This resulted in invalid log, since they were not NULL-terminated
strings. Use MQTT_UTF8_LITERAL() to initialize both utf8 strings to make
sure they are NULL-terminated now and valid to print and
log. Additionally this makes the code a bit shorter.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There are scenarios where there is a NAT firewall in between MQTT
client and server. In such case, the NAT TCP timeout may be shorter
than MQTT keepalive timeout and TCP timeout. The the MQTT ping
request message is dropped by the NAT firewall, so that it cannot be
received by the server, resulting in void MQTT ping response message.
There is no TCP FIN or RST at all. The application looks hang-up
until TCP timeout happens on the client side, which may take too
long.
Therefore, the event MQTT_EVT_PINGRESP is added to inform the
application that the route between client and server is still valid.
Signed-off-by: PK Chan <pak.kee.chan@nordicsemi.no>
This commit updates the the IPv4 ping command to handle the ENETUNREACH
error number returned by `net_icmpv4_send_echo_request` function when
IPv4 is unavailable.
The `net_icmpv4_send_echo_request` function previously returned EINVAL
when IPv4 is unavailable and this caused the shell command to report
"Invalid IP address" even when the provided IP address is correct; this
problem was corrected by returning ENETUNREACH instead of EINVAL in the
aforementioned function.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
net_icmpv4_send_echo_request currently returns EINVAL (invalid
argument) when IPv4 is unavailable.
Since the availability of IPv4 has nothing to do with the arguments
provided to this function and the meaning of EINVAL in this case is
ambiguous, return the ENETUNREACH (network is unreachable) error
number instead.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The TCP connection might be concurrently modified from the
TR/TX threads, so add a mutex to protect from the concurrent
modification.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
After removing the test windows, update test protocol
functions for the TTCN-3 sanity check.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
These test receive windows were used by TTCN-3 sanity check,
but it's possible to do without them.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In order to drop dependency on a heap, drop the
test send window.
Use net_tcp_queue_data() to receive the outgoing data
from the socket layer.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In order to drop dependency on a heap, drop the test
receive window.
The receive window was needed for TTCN-3 sanity check,
but it's possible to do without it.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
On incoming SYN+ACK, use the existing TCP connection.
This problem was overlooked earlier and was found while
testing TCP2 client side.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In SYN_SENT check the ack number of the incoming TCP message
against our sequence number.
This problem was overlooked earlier and was found while
testing TCP2 client side.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Don't erroneously instantiate an extra TCP connection
on TCP connect.
This problem was overlooked earlier and found while testing
TCP2 client side.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
k_timer callback is executed from ISR context, which isn't
currenty compatible with Zephyr's shell implementation.
This problem was found while testing TCP2 client side.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In order to support TTCN-3 based TCP2 sanity check,
register test inputs with net_conn_register() and adjust
test functions to account for this.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In order to support IPv4/IPv6, work with packet through
net_pkt_ip_hdr_len(), net_pkt_ip_opts_len() which account
for IPv4/IPv6, IPv4 options and IPv6 extension headers.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Remove temporary interception of TCP, UDP for TTCN-3 based
TCP2 sanity check.
As a part of adding IPv6 support, TCP2 will register test
callbacks/inputs with net_conn_register().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Allocate tcp2.c endpoints before storing port numbers or addresses.
Select the IPv4 source address since net_context_create_ipv4_new()
is not currently called on packet output.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
NET_OFFLOAD interfaces do not handle ICMP request. Request to send ICMP
packet resulted in NULL pointer dereference in net_if_tx() later
on. Prevent that by detecting NET_OFFLOAD interfaces early in icmpv4
module.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
OpenThread has api to make use of radios energy scan feature.
Implemented this api in zephyr. This allows thread to perform energy
scan when needed.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
If the system has more than one network interface, then it should
be possible to bind a AF_PACKET socket to each interface if the
network interface index is set when bind() is called. This was
not possible earlier as the code was always using default network
interface with AF_PACKET socket bind().
Fixes#23153
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
According to LWM2M specification, when Queue Mode is used, the LWM2M
client should keep the reciever on for specified time after sending A
CoAP message. This commit adds a new LWM2M event,
`LWM2M_RD_CLIENT_EVENT_QUEUE_MODE_RX_OFF`, to facilitate the process by
notifying the application when it's safe to turn the receiver off.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add Kconfig option to enable Queue Mode binding. With this option
enabled, the LWM2M client will register with `UQ` binding, instead of
`U`.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Calculate length based on provided SSID string, so user does not have to
provide length explicitly over shell.
This patch also removes requirement of minimum 3 characters SSID, as
the shortest SSID can be even 1 character.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Older OT code used preprocessor #if conditionals, while newer code
used IS_ENABLED macro. Unify the approach by switching to the latter
option.
Additinally, fix inclusion issue that came out after switching to
IS_ENABLED.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add new transport handler for MQTT, with sendmsg-like functionality.
This allows TCP transport to send PUBLISH packets w/o fragmentation at
the TCP layer. Implement this new functionality for all existing
transports.
Fixes#22679
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
`mqtt_transport_write` failue was logged with `errno` value which is not
correct as the return value from the function is valid in this case.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This option specifies the name of the client.
See https://tools.ietf.org/html/rfc2132#section-3.14
This is useful for identification when looking in DHCP lease table.
Signed-off-by: Luuk Bosma <l.bosma@interay.com>
We now negotiate DNS servers in the IPCP configuration. This has been
observed to speed up the connection setup. The received DNS servers
are used by the DNS resolver library, but we leave it optional since
the static server list might be preferable.
Increase MAX_IPCP_OPTIONS to 4 so that we can nack all RFC 1877
options.
Signed-off-by: Göran Weinholt <goran.weinholt@endian.se>
It is not unusual that the peer does not provide an IP address in the
ipcp negotiation. But because ppp is a peer-to-peer protocol, we do
not actually need to know the peer's address to use the network.
Signed-off-by: Göran Weinholt <goran.weinholt@endian.se>
TLS sockets did not increase refcount of a net_context running TCP,
which could lead to a crash upon TCP disconnection.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
opts_len renamed to total_opts_len in previous changes.
But it's not replaced at one place.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If IPv4 header options has wrong options length
(e.g. options length is more that actual data),
then parser decrements opts_len without checking
actual data length. Which crashes the network stack.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Store the time difference value in u32_t variable than
abs() value in signed variable.
Fixes#22912
Coverity CID: 208406
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
net_pkt_clone() initializes the original packet cursor
and clone the packet. But it doesn't restore the cursor
back to original position.
Issue noticed when mDNS resolving fails when mdns responder
is also enabled.
net_conn_input(), in case of multicast packet, connection
handler clone the packet and deliver to matching handler.
Example case: dns_resolver and mdns_responder both register
handlers for 5353 port. After first clone original packet
cursor moved back to starting position. But first cloned
packet cursor is set properly. Second time cloning makes
cursor position to set to zero. Which makes second packet
handler header unpacking goes wrong.
Fixes#21970.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
If nack_idx > 0, then the count_rej must be > 0. This means that
the "code" variable will never be set to PPP_CONFIGURE_NACK.
Fixes#22436
Coverity-CID: 207975
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If CONFIG_NET_PKT_RXTIME_STATS is set, then update the received
packet RX time for packet sockets (SOCK_RAW). This was already
working for normal sockets but the statistics update was missing
from SOCK_RAW.
Fixes#22489
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
commit e3dc05f14d ("net: config: Wait network interface to come up")
introduced check_interface() function, which accidentally has 2
different signatures depending on CONFIG_NET_NATIVE selection.
Let's fix the second signature to be correct.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/22693
Signed-off-by: Michael Scott <mike@foundries.io>
The zsock_accept_ctx() calls z_reserve_fd() on entry but fails
to call z_free_fd() on failure. This will leak the allocated
socket descriptor.
Fixes#22366
Signed-off-by: Inbar Anson Bratspiess <inbar.anson.bratspiess@330plus.net>
I think people might be reading differences into 'if' and 'depends on'
that aren't there, like maybe 'if' being needed to "hide" a symbol,
while 'depends on' just adds a dependency.
There are no differences between 'if' and 'depends on'. 'if' is just a
shorthand for 'depends on'. They work the same when it comes to creating
implicit menus too.
The way symbols get "hidden" is through their dependencies not being
satisfied ('if'/'depends on' get copied up as a dependency on the
prompt).
Since 'if' and 'depends on' are the same, an 'if' with just a single
symbol in it can be replaced with a 'depends on'. IMO, it's best to
avoid 'if' there as a style choice too, because it confuses people into
thinking there's deep Kconfig magic going on that requires 'if'.
Going for 'depends on' can also remove some nested 'if's, which
generates nicer symbol information and docs, because nested 'if's really
are so simple/dumb that they just add the dependencies from both 'if's
to all symbols within.
Replace a bunch of single-symbol 'if's with 'depends on' to despam the
Kconfig files a bit and make it clearer how things work. Also do some
other minor related dependency refactoring.
The replacement isn't complete. Will fix up the rest later. Splitting it
a bit to make it more manageable.
(Everything above is true for choices, menus, and comments as well.)
Detected by tweaking the Kconfiglib parsing code. It's impossible to
detect after parsing, because 'if' turns into 'depends on'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
When is NET_SOCKETS_SOCKOPT_TLS set, it should set TLS_CREDENTIALS
even when NET_NATIVE=n, so that platforms that use socket offloading
can continue to set TLS credentials.
We are now setting this via 'imply' instead of 'select', so that
prj.conf can opt out if necessary.
Fixes#22390
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Instead of using a custom offloading interface, users can use
`NET_SOCKET_REGISTER` macro to register custom socket API provider. This
solution removes a limitation, that only one offloaded interface can be
registered and that it cannot be used together with native IP stack.
The only exception remainig are DNS releated operations -
`getaddrinfo`/`freeaddrinfo`, which, when offloaded, have to be
registered specifically.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Sort out mbedTLS dependencies in sockets Kconfig. mbedTLS will now
be enabled when TLS sockets and native network stack are enabled.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Each network interface needs to have IPv6 link local address.
The ll address was not set to VLAN interfaces which then caused
some of the IPv6 neighbors to be in wrong state (INCOMPLETE) in
neighbor cache.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When we are about to send a NS, we should not use the destination
address as that is typically the multicast address. We should use
the target address instead.
This fixes the case where a neighbor is in incomplete state, and
we send a neighbor solicitation to find out whether the neighbor
is reachable. In this case the destination address is the solicited
node multicast address which is no use when trying to figure out
the source address.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit fixes a problem where our own IP address
is added to the cache instead of the senders.
This bug was due to a swap of the address in the original packet.
The swapping of the address is now removed.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Users of mqtt_live() have no idea when it actually sends a ping.
As a result it's very hard to know when to use mqtt_input() to
process the incoming PINGACK.
Instead of returning a 0 result when a ping isn't generated in
mqtt_live(), let's return -EAGAIN.
Signed-off-by: Michael Scott <mike@foundries.io>
Make sure that if we receive websocket data in small chunks,
the parsing and returning of data to caller is done properly.
Fixes#21989
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Store the IPv4 address into the local LCP options and set it
as the interface IP address once IPCP negotiation is complete.
Fix calling the correct function when an IPCP Configure Reject
is received carrying our local IP address.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
The MQTT connection is closed in case an mqtt_ping fails anyway, so
it's better to let the application know early that something went
wrong.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
As mDNS requests set DNS id to 0, we cannot use it to match
the DNS response packet. In order to allow this functionality,
create a hash from query name and type, and use that together
with DNS id to match request and response.
Fixes#21914
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
A neighbor solicitation packet for an address that is not ours should
not cause the sender to be added to the neighbor cache. See RFC 4861
section 7.2.3.
Add the neighbor to the cache when we have decided to respond to the
NS packet.
Fixes#21869.
Signed-off-by: Jonas Norling <jonas.norling@greeneggs.se>
Use the same code when parsing source link-layer address option for
both RA and NS packets. It looked like handle_ns_neighbor() could
actually read too much data into lladdr.addr when handling 8-byte
addresses (802.15.4).
Signed-off-by: Jonas Norling <jonas.norling@greeneggs.se>
Make ioctl handlers of `ZFD_IOCTL_POLL_PREPARE` and
`ZFD_IOCTL_POLL_UPDATE` return an error code instead of setting errno
variable.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
A memory corruption could happen in `uncompress_IPHC_header` function,
when data was moved to make place in the net buffer for the uncompressed
IPv6/UDP header.
The size of data being moved should only contain the original data size,
not incremented by the amount of space needed to expand the header,
which was already added to the net buffer size. In result, the `memmove`
operation could exceed the allocated net buffer and cause memory
corruption.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
If no other route is found, the network interface prefixes are
evaluated. If a matching interface is found, the packet is sent out on
this interface.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
The address family of the received packet must be set, before routing
it. E.g. the ethernet driver would drop the packet if this is not
done.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Add function that returns remaining time until next keep alive message
shall be sent. Such function could be used for instance as a source
for `poll` timeout.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
generated_dts_board.h is pretty redundant and confusing as a name. Call
it devicetree.h instead.
dts.h would be another option, but DTS stands for "devicetree source"
and is the source code format, so it's a bit confusing too.
The replacement was done by grepping for 'generated_dts_board' and
'GENERATED_DTS_BOARD'.
Two build diagram and input-output SVG files were updated as well, along
with misc. documentation.
hal_ti, mcuboot, and ci-tools updates are included too, in the west.yml
update.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The transition from LISTEN to SYN_SENT nullifies the th,
guard on th being NULL in SYN_SENT.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In case the final ACK for the connection establishment arrives
out of order, evaluate the sequence number in SYN_RECEIVED,
so the data packet isn't false identified as a final ACK.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In order to simplify the evaluation of the incoming data,
add len and evaluate the data for the incoming packet once.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Create a new connection only for the SYN packet,
otherwise pass a packet into existing connection.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
The initial logic with this check is too restrictive,
do not bail-out on unconsumed flags.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Add a diagnostic information on network buffer sizes
and the total length of the packet.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Set the net_context to NET_CONTEXT_CONNECTED state only once
in transitions to TCP_ESTABLISHED.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
1. Reduce the internal buffer
2. Eliminate extra string pointer
3. Add a comment on deleting the last comma
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In order to avoid naming collision with tcp_recv(),
rename tcp_recv() into tp_tcp_recv().
This function is used by the test protocol.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
After sending the MQTT disconnect message, no response is expected,
therefore it makes little sense to delay the socket closure.
So far it was expected to call `mqtt_input` function after calling
`mqtt_disconnect` in order to close the socket, which is
counter-intuitive. Simplify this, by closing the socket rightaway
in the `mqtt_disconnect` function.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
OpenThread settings implementation built on top of Zepyhr settings
submodule.
With this solution, OpenThread settings are identified with keys of
the following format: `ot/id/instance`, where `id` is assigned by
OpenThread stack, and `instance` is a 32-bit random number, both in
hex. The implementation makes use of `settings_load_subtree_direct`
function to iterate over settings instances. This allows the
OpenThread settings layer to be a fully transparent shim layer between
OpenThread/Zephyr APIs.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Remove net bufs own assertion mechanism and use the system assert
instead. This changes the assertion messaged printed from printing
expression to printing the line and file name. This provides more
context as the same expression could be asserted upon multiple times and
would then not provide enough clarity in the message.
This removes the option to enable only net buf assertions.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Drop snprintf() and use snprintk() as snprintk()
is more suitable for the networking code.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
NET_BUF_ASSERT() tranlates into nothing in presence
of CONFIG_ASSERT=y, which is misleading.
Use __ASSERT() in NET_BUF_ASSERT().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
No packet was previously sent, because net_pkt_set_ppp(pkt, true) was
not called on the outgoing packet. Also the received protocol instead of
LCP was used, which was incorrectly interpreted by remote peer.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Received net_pkt is always discarded in ppp_recv() if we return
NET_OK. Don't do this in ppp_fsm_recv_discard_req().
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
When iterating though configuration options it is possible that we will
fail to add data to nack_buf and hence unref it in error handling
path. Just after that we will unref buf, which has nack_buf in its
buffer chain.
Drop code unrefing nack_buf and just go directly to unrefing buf.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There is no possibility right now that 'nack == NULL' and 'nack_buf !=
NULL', so drop code path for that case.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
If we can write to the socket in POLLOUT, then there is no need to
wait.
Note that this is not a full POLLOUT implementation but prevents
the code from waiting even if we could send data out.
Fixes#18867
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Same deal as in commit 41713244b3 ("kconfig: Remove '# Hidden' comments
on promptless symbols"). I forgot to do a case-insensitive search.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Make the channel ops struct const since there really isn't anything
there that needs to change at runtime. The only exception is the L2CAP
shell which was playing with the recv callback, however that can be
fixed by introducing a simple bool variable.
With tests/bluetooth/shell this reduces RAM consumption by 112 bytes
while adding only 16 bytes to flash consumption.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Maintain a simple count of how many PINGREQ have been sent for the
current connection that have not had a corresponding PINGRESP. Nothing
is done with this information internal to the MQTT driver, but it is
exposed to the application layer to monitor as desired.
Signed-off-by: Justin Brzozoski <justin.brzozoski@signal-fire.com>
The commit 8892406c1d ("kernel/sys_clock.h: Deprecate and convert
uses of old conversions") changed code to not use deprecated macro.
Unfortunately there was some changes done to RX TC stats update that
were missing from that commit. This commit fixes the issue and removes
the last user of the deprecated SYS_CLOCK_HW_CYCLES_TO_NS64() macro.
This is follow up to commit 5bbdf56769 ("net: stats: Fix RX time
statistics update") which failed to remove all users of the deprecated
macro.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Based on work by Michael Scott.
Add a new Kconfig knob, CONFIG_LWM2M_IPSO_TIMESTAMP_EXTENSIONS. This
defaults to n. When enabled, various IPSO objects will by default have
the timestamp resource (5518) added to their representations. This can
be turned off on a per-object basis.
The idea of adding timestamp resources was originally suggested by
Hannes Tschofenig on this OMA page:
https://github.com/OpenMobileAlliance/OMA_LwM2M_for_Developers/issues/429
Signed-off-by: Michael Scott <mike@foundries.io>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The commit 8892406c1d ("kernel/sys_clock.h: Deprecate and convert
uses of old conversions") changed code to not use deprecated macro.
Unfortunately there was some changes done to RX stats update that were
missing from that commit. This commit fixes the issue and removes use
of the deprecated SYS_CLOCK_HW_CYCLES_TO_NS64() macro.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Follwing the convention in Zephyr, all CMake configuration related to
a module, should be placed within the module repostiory.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Timestamp and RecordRoute options are supported
in only ICMPv4 EchoRequest call as per
RFC 1122 3.2.2.6.
Fixes#14668
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
IPv4 header options length will be stored in ipv4_opts_len
in net_pkt structure. Now IPv4 header length will be in
net_pkt ip_hdr_len + ipv4_opts_len. So modified relevant
places of ip header length calculation for IPv4.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
OpenThread recently introduced CMake build system into its repostiory
so we no longer need autotools to build OpenThread libraries and can
integrate them natively.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The TCP code expects that we know when the socket has called accept()
in order to continue connection attempt.
Fixes#21335
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Packets shall never fail to be sent now that they are queued, so if an
error occured there is no point in keep the channel connected.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Functions like `setup_ipv4` or `setup_ipv6` might already use the
`counter` semaphore, therefore it should be initialized before these
functions are called.
As a result of this issue, the network stack could stall until timeout
under certain circumstances (e.g. when OpenThread was used).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
An expired IPv6 router would cause an infinite loop where
iface_router_run_timer() repeatedly scheduled a work item. In some
conditions it would schedule with negative delay, in other conditions
the infinite loop wouldn't happen until a router was added again.
Get rid of the router from active_router_timers when it is removed.
Fixes#21339
Signed-off-by: Jonas Norling <jonas.norling@greeneggs.se>
Without this fix is it not possible to terminate pppd and restart
pppd afterwards without restarting the firmware, too.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Without this fix is it not possible to terminate pppd and restart
pppd afterwards without restarting the firmware, too.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This adds net_bug_simple_init_with_data which can be used to initialize
a net_buf_simple pointer with an external data pointer.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Before we try to set IP addresses to the network interface,
make sure that the interface is up.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Allow to select Sleepy End Device, and configure it during OpenThread
initialization.
According to Thread Specification, Sleepy End Devices should always
attach to the network as SED, to indicate increased buffer requirement
to a parent. Therefore, we reconfigure the Link Mode on each boot.
Note, that Poll Period value is not stored in the persistent storage,
hence we also need to initialize it on each boot.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
OpenThread radio layer did not implement `ieee802154_radio_handle_ack`
API and provided fake ACK frame to the OpenThread.
This prevented proper Sleepy End Device operation, as it expects to
receive information in the ACK whether it should wait for more data to
come or should it put the radio to sleep.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The time difference calculation did not check if the result
value would be < 0 which means really large value when converted
to unsigned.
Fixes#20100
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For 32-bit architecture Bluetooth only requires 4 bytes for the user
data. There are places that store a pointer in it, so we need to make
an exception for 64-bit architecture. The code contains relevant build
asserts, so it's sufficient to set a conditional default in Kconfig
but let the range definition be simpler (unconditional).
Also simplify & fix the conditional defaults & ranges. E.g. separately
mentioning X86_64 is redundant since that option explicitly selects
the 64BIT option.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add an implementation for `sendmsg`, so secure sockets can be used
together with the WebSocket module to implement secure WebSockets
("wss").
Fixes#20431
Signed-off-by: Markus Fuchs <markus.fuchs@de.sauter-bc.com>
This commit adds a NULL pointer check for the destination
context pointer. The pointer is NULL in case the context
does not exist.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Setting it to UINT32_MAX, as it is subsequently overwritten with
MIN(oldest, something_else).
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Mark the old time conversion APIs deprecated, leave compatibility
macros in place, and replace all usage with the new API.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This commit refactors kernel and arch headers to establish a boundary
between private and public interface headers.
The refactoring strategy used in this commit is detailed in the issue
This commit introduces the following major changes:
1. Establish a clear boundary between private and public headers by
removing "kernel/include" and "arch/*/include" from the global
include paths. Ideally, only kernel/ and arch/*/ source files should
reference the headers in these directories. If these headers must be
used by a component, these include paths shall be manually added to
the CMakeLists.txt file of the component. This is intended to
discourage applications from including private kernel and arch
headers either knowingly and unknowingly.
- kernel/include/ (PRIVATE)
This directory contains the private headers that provide private
kernel definitions which should not be visible outside the kernel
and arch source code. All public kernel definitions must be added
to an appropriate header located under include/.
- arch/*/include/ (PRIVATE)
This directory contains the private headers that provide private
architecture-specific definitions which should not be visible
outside the arch and kernel source code. All public architecture-
specific definitions must be added to an appropriate header located
under include/arch/*/.
- include/ AND include/sys/ (PUBLIC)
This directory contains the public headers that provide public
kernel definitions which can be referenced by both kernel and
application code.
- include/arch/*/ (PUBLIC)
This directory contains the public headers that provide public
architecture-specific definitions which can be referenced by both
kernel and application code.
2. Split arch_interface.h into "kernel-to-arch interface" and "public
arch interface" divisions.
- kernel/include/kernel_arch_interface.h
* provides private "kernel-to-arch interface" definition.
* includes arch/*/include/kernel_arch_func.h to ensure that the
interface function implementations are always available.
* includes sys/arch_interface.h so that public arch interface
definitions are automatically included when including this file.
- arch/*/include/kernel_arch_func.h
* provides architecture-specific "kernel-to-arch interface"
implementation.
* only the functions that will be used in kernel and arch source
files are defined here.
- include/sys/arch_interface.h
* provides "public arch interface" definition.
* includes include/arch/arch_inlines.h to ensure that the
architecture-specific public inline interface function
implementations are always available.
- include/arch/arch_inlines.h
* includes architecture-specific arch_inlines.h in
include/arch/*/arch_inline.h.
- include/arch/*/arch_inline.h
* provides architecture-specific "public arch interface" inline
function implementation.
* supersedes include/sys/arch_inline.h.
3. Refactor kernel and the existing architecture implementations.
- Remove circular dependency of kernel and arch headers. The
following general rules should be observed:
* Never include any private headers from public headers
* Never include kernel_internal.h in kernel_arch_data.h
* Always include kernel_arch_data.h from kernel_arch_func.h
* Never include kernel.h from kernel_struct.h either directly or
indirectly. Only add the kernel structures that must be referenced
from public arch headers in this file.
- Relocate syscall_handler.h to include/ so it can be used in the
public code. This is necessary because many user-mode public codes
reference the functions defined in this header.
- Relocate kernel_arch_thread.h to include/arch/*/thread.h. This is
necessary to provide architecture-specific thread definition for
'struct k_thread' in kernel.h.
- Remove any private header dependencies from public headers using
the following methods:
* If dependency is not required, simply omit
* If dependency is required,
- Relocate a portion of the required dependencies from the
private header to an appropriate public header OR
- Relocate the required private header to make it public.
This commit supersedes #20047, addresses #19666, and fixes#3056.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Added in commit 106a0f7306 ("net: lib: config: Add SYS_INIT handler to
set clock from SNTP"), never used.
Found with a script.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
In order to avoid net_pkt ref count going to <0, do not unref
the packet if it was not sent in the first place. This can happen
if the connection was closed while we are waiting packets to be sent.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Do not print warning if transitioning from LISTEN -> CLOSED which
happens when the socket is closed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The initial state from CLOSED -> ESTABLISHED caused error
to be printed by state validator. This is unnecessary, so add
this as a valid state to validator.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Handle this corner case with TCP connection closing:
1) Client A connects, it is accepted and can send data to us
2) Client B connects, the application needs to call accept()
before we will receive any data from client A to the application.
The app has not yet called accept() at this point (for
whatever reason).
3) Client B then disconnects and we receive FIN. The connection
cleanup is a bit tricky as the client is in half-connected state
meaning that the connection is in established state but the
accept_q in socket queue contains still data which needs to be
cleared.
4) Client A then disconnects, all data is sent etc
The above was not working correctly as the system did not handle the
step 3) properly. The client B was accepted in the application even
if the connection was closing.
After this commit, the commit called "net: tcp: Accept connections
only in LISTENING state" and related other commits are no longer
needed and are reverted.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add CONFIG_NET_TCP_AUTO_ACCEPT option which can be used to
automatically accept incoming data connection even if the
application has not yet called accept(). This can speed up
data transfer from peer to the application.
Problem with this is that if the peer sends lot of data and
we have limited amount of net_buf's available, then we can
run out of them which is very bad situation and can lead to
deadlocks. Because of this, the setting is turned off by default.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This reverts commit d70a854904.
The next commit fixes the original issue so this commit is no
longer needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
With this feature enabled (via CONFIG_NET_CONFIG_CLOCK_SNTP_INIT), an
application will automagically get correct absolute time via POSIX
functions like time(), gettimeofday(), etc.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Use the newest version of the OpenThread project, as updated in
https://github.com/zephyrproject-rtos/openthread/pull/2.
Introduce the following fixes along with the update (they're squashed to
retain bisectability of OT samples):
* Update configs and flags used
Some OT configs were renamed, some new were introduced that Zephyr port
needs to set.
* Add entropy platform driver
OpenThreads `random` platform subsystem was replaced with `entropy`
subsystem which is supposed to serve as an entropy source for the
generic OpenThread's random generator.
* Halt OT thread when OT command is processed
OpenThread can currently be processed from two threads - a
genuine OpenThread thread and shell thread, which processes CLI
commands. This could cause trouble, when context was switched
during OT command processing (i.e. switched to process an incomming OT
message, while still in unfinished command handler).
In result, it was not possible to turn the commissioner role on via
CLI, as the commissioner petition response was handled before the
Commissioner::Start function finished its execution (if the
petitioner is also the network leader, all messages are passed
internally within the stack).
Fix this by suspending the OT thread for the time of an OT command
processing.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In order to properly remove struct tcp and its data, net_context
needs to be supplied as k_timer user data. Modify net_tcp_unref()
to take a net_context argument when removing, and add ifdefs
around code that after this will only be used by TCP testing
functionality.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Add a net_context backpointer and receiver user data to the tcp
structure. Once the desired callback and user data is set in
net_tcp_recv(), net_context_packet_received() can be called at
TCP reception in tcp_data_get(), moving the TCP data to the
recipient. IP and TCP protocol headers are sent as NULL, they
are not used by e.g. the socket code.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Since TCP needs to be able to decide how much data is to be sent
in a TCP segment and when the segment needs to be sent, the TCP
data buffer needs to be passed down to the TCP stack. For tcp2
this causes a new function handling the data as a buffer or as an
iov to be implemented and only that function is called when
sending data out via the new TCP stack. net_tcp_send_data() is
invoked as the caller expects to be informed when the data has
been sent.
For the current stack keep the sending functions as is.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Register the TCP connection when accept() and connect() is called.
With the connection registration net_context will have the necessary
callback pointer set up, whereby net_context can call the proper
function when receiving packets for the TCP connecton.
With the new TCP stack this callback is always the same function.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Currently the TCP commands work only for legacy TCP.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Applications should use setsockopt() to setup the SOCKS5 proxy,
so the old API file, which is using net_context directly, is
moved SOCKS5 directory.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fix GCC "warning: 'ipv4' defined but not used [-Wunused-variable]" and
"warning: 'ipv6' defined but not used [-Wunused-variable]" when either
IPv4 or IPv6 support is not enabled.
Signed-off-by: Markus Fuchs <markus.fuchs@de.sauter-bc.com>
Use sys_put_xyz() helpers instead of memcpy() whenever possible. This
brings in straight-line inline code for pushes and adds of known,
small sizes.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
On processing a DNS server option, which re-initializes the DNS resolve
context, also cancel all pending DNS queries before closing the old DNS
resolve context. Otherwise, `z_clock_announce()` will later work on the
re-initialized context once the queries expire and crash because the
reference to the timeout function `query_timeout()` has been cleared.
Signed-off-by: Markus Fuchs <markus.fuchs@de.sauter-bc.com>
Unused after commit a76814bfb6 ("net: Convert core IP stack to use log
levels").
Found with a script.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use same format string when printing information that certain
config option is not enabled. This saves some flash as the
same string can be shared in the shell.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
LWM2M_FIRMWARE_UPDATE_PULL_LOCAL_PORT is unused since commit 54c10c04e5
("net: lwm2m: use security data for connections").
Found with a script.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Unused since commit d1cb39e7ce ("net: lwm2m: migrate LwM2M library to
BSD-sockets API").
Found with a script.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The earlier code was always queuing the FIN that is sent when
connection is closed. This caused long delay (200 ms) before the peer at
the other end noticed that the connection was actually closed.
Now check if there is nothing in the queue, then send the FIN
immediately. If there is some data in the queue, flush it when a valid
ack has been received.
Fixes#19678
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
With `CONFIG_NET_NATIVE`, offloaded drivers can specify capabilites with
`NET_IPV4/6` configs, so there is no longer need to handle socket
offloading separately.
Also, initialize hints structure with zeros, as according to man pages
unused fields should be set to 0:
`All the other fields in the structure pointed to by hints must contain
either 0 or a NULL pointer, as appropriate.`
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add new config option `LWM2M_DNS_SUPPORT` to the LWM2M library, instead
of relying on `DNS_RESOLVER` which is only compatible with native
network stack. This allows to use DNS with offloaded interfaces
seamlessly.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This is related to commit 1a6f4a6368 ("net: tcp: Accept
connections only in LISTENING state") which made the system
to only accept new connections if the application had called
accept(). Unfortunately the TLS accept was not fixed by that
commit so we were in wrong state when accepting TLS sockets.
This commit fixes that issue.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
A socket-offloaded interface should bypass interface initialization in
the same way as net-offloaded interface does.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This function will be useful in shell when we want to monitor
the amount of bytes transferred and want to clear earlier
statistics.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print information about how long network packets took from
application to the network device driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Calculate how long on average net_pkt has spent on its way from
application to the network device driver. The data is calculated
for all network packets and not just for UDP or TCP ones like in
RX statistics.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print information about how long network packets took from
network device driver to the application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Calculate how long on average net_pkt has spent on its way from
network device driver to the application. The data is only
calculated for UDP and TCP network packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Send a Echo-Reply to every Echo-Request. This code does not verify
if the ppp stm is in LCP Opened state. See rfc1661 section 5.8.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Re-run with updated script to convert integer literal delay arguments
to k_thread_create and K_THREAD_DEFINE to use the standard timeout
macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Try to figure out where the ping reply should be sent if there
are multiple network interfaces in the system.
Fixes#19612
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The MQTT transport API functions are already documented in
mqtt_transport.h so need to duplicate them in individual
transport .c file.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Randomly generating ID the first time coap_next_id() is called is more
in accordance with CoAP recommendations (see
https://tools.ietf.org/html/draft-ietf-core-coap-18, section 4.4)
"It is strongly recommended that the initial value of the
variable (e.g., on startup) be randomized, in order to make successful
off-path attacks on the protocol less likely."
Doing this in a dedicated init function is the cleanest and most
idiomatic approach. This init function is not exposed publically which
means it will be called only once, by the network stack init procedure.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
Provides a way to clone a net_buf_simple without altering the state of
the original buffer. The primary usage scenario is for manipulating a
previously allocated PDU inside a buffer without altering the length and
offset of the buffer.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
create_ipv6_answer() function is behind #define's but get used behind
IS_ENABLED(CONFIG_NET_IPV6), which is not allowed.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Use the int_literal_to_timeout Coccinelle script to convert literal
integer arguments for kernel API timeout parameters to the standard
timeout value representations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The main and idle threads, and their associated stacks,
were being referenced in various parts of the kernel
with no central definition. Expose these in kernel_internal.h
and namespace with z_ appropriately.
The main and idle threads were being defined statically,
with another variable exposed to contain their pointer
value. This wastes a bit of memory and isn't accessible
to user threads anyway, just expose the actual thread
objects.
Redundance MAIN_STACK_SIZE and IDLE_STACK_SIZE defines
in init.c removed, just use the Kconfigs they derive
from.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The callback function has been ignored in z_timeout_init() since the
timer rework in fall 2018. Passing real handlers to it in code is
distracting when they will be overridden by whatever callback is
provided in z_add_timeout().
As this function is an internal API deprecation is not necessary.
Remove the parameter and change all call sites to drop the argument.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Cast a %lld argument to long long int. This is causing warnings on
recent GNU Arm Embedded toolchains, which fail the build with
-Werror=format=.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
* The issue is found in supporting offload module esp8266
* For device like esp8266, it's responsible for tcp/udp handling,
no need of net_tcp related functions
* This commit is only tested for esp8266, no gurantee for other
modules
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Currently the CONFIG_NET_ROUTING option has limited use as there
would be some entity that populates routing table. Previously it
was RPL that did it but RPL support was removed some time ago.
Fixes#16320
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we are getting an old net_context, clear the content of it
in order to make sure we do not have old data in it.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Do not try to re-use net_context.user_data field as in many places
(like in accept) it is expected to contain pointer to net_context.
Storing the socket flags will corrupt the value. To simplify and
make things less error prone, use socket specific field in net_context
to store the socket flags.
Fixes#19191
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
So far OpenThread compiled it's own, internal copy of mbedTLS library.
This commit changes this behavior by using Zephyr's mbedTLS instance
appropriately configured for OpenThread needs.
Generic mbedTLS config file was used in this case, so that application
can still configure remaining parts of mbedTLS for it's own needs.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The socket flags are stored in void* so we need to use uintptr_t
instead of u32_t when manipulating the flag variable.
Fixes#19181
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We need to make sure that net_pkt_clone() sets cursor correctly.
This cursor position is needed so that we can skip IP header
for incoming packet properly. Not all applications need to know
the cursor position of the cloned packet. Unfortunately we cannot
know that in advance so just set the cursor to correct position in
the cloned packet.
Fixes#19135
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If socket is marked non-blocking, then accept() will return immediately
if there is no one connecting.
Fixes#19103
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
SNTP is UDP-based protocol, and thus not reliable. Previously,
high-level aka "simple" SNTP just issues a single request via
the low-level SNTP API. Instead, send multiple requests, starting
with a small timeout, and exponential backoff, repeated within
timeout specified by user in call to sntp_simple().
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If we receive a multicast IPv4 or IPv6 packet, then we need to
deliver it to all sockets that have installed a handler for it.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Previously, they were tested only with CONFIG_NET_SOCKETS_POSIX_NAMES,
but should also work with POSIX subsys. Achieve this by including POSIX
headers in this case.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If proto field in socket() call is set to 0, then we should have
a sane default for it that depends on the type of the socket.
Fixes#18873
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The semi-automated API changes weren't checkpatch aware. Fix up
whitespace warnings that snuck into the previous patches. Really this
should be squashed, but that's somewhat difficult given the structure
of the series.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
These calls are buildable on common sanitycheck platforms, but are not
invoked at runtime in any tests accessible to CI. The changes are
mostly mechanical, so the risk is low, but this commit is separated
from the main API change to allow for more careful review.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
System call arguments, at the arch layer, are single words. So
passing wider values requires splitting them into two registers at
call time. This gets even more complicated for values (e.g
k_timeout_t) that may have different sizes depending on configuration.
This patch adds a feature to gen_syscalls.py to detect functions with
wide arguments and automatically generates code to split/unsplit them.
Unfortunately the current scheme of Z_SYSCALL_DECLARE_* macros won't
work with functions like this, because for N arguments (our current
maximum N is 10) there are 2^N possible configurations of argument
widths. So this generates the complete functions for each handler and
wrapper, effectively doing in python what was originally done in the
preprocessor.
Another complexity is that traditional the z_hdlr_*() function for a
system call has taken the raw list of word arguments, which does not
work when some of those arguments must be 64 bit types. So instead of
using a single Z_SYSCALL_HANDLER macro, this splits the job of
z_hdlr_*() into two steps: An automatically-generated unmarshalling
function, z_mrsh_*(), which then calls a user-supplied verification
function z_vrfy_*(). The verification function is typesafe, and is a
simple C function with exactly the same argument and return signature
as the syscall impl function. It is also not responsible for
validating the pointers to the extra parameter array or a wide return
value, that code gets automatically generated.
This commit includes new vrfy/msrh handling for all syscalls invoked
during CI runs. Future commits will port the less testable code.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
If we are returned IPv4 address but the hints says IPv6, then
return error as currently we do not support AI_V4MAPPED addresses.
Same check for IPv6 if we want only IPv4 address.
Fixes#18870
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Issue noticed with following scenario.
1) TCP server is listening for connections but will handle
only one connection at a time (e.g. echo-server sample)
2) Client A connects, and the connection is accepted.
3) Client B connects, instead of denying a connection,
it is "auto" accepted (this is the actual bug) even
if the application has not called accept().
4) After the connection A is closed, the connection B
gets accepted by application but now the closed
connection A will cause confusion in the net-stack
5) This confusion can cause memory leak or double free
in the TCP core.
It is not easy to trigger this issue because it depends
on timing of the connections A & B.
Fixes: #18308
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If we are closing connection before the connection was established,
then unref the context so that the cleanup is done properly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Allow user to disable native IP stack and use offloaded IP
stack instead. It is also possible to enable both at the same
time if needed.
Fixes#18105
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit adds an explicit inclusion of toolchain.h from
ieee802154_frame.h.
The endianness preprocessor definitions (__BYTE_ORDER__,
__ORDER_LITTLE_ENDIAN__, __ORDER_BIG_ENDIAN__) are used by
ieee802154_frame.h; these being not defined can easily go unnoticed and
cause unexpected behaviours, as detailed in PR #18922.
toolchain.h ensures that these preprocessor definitions are defined and
*must* be included in a file that uses these definitions.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
When using offloaded network, an L2 is never assigned to the net_if.
Only certain portions of the net_if code are referenced such as:
net_if_up()
net_if_down()
And these functions make use of several L2 references:
get_flags()
enable()
Let's add checks to make sure we don't deref a NULL when using these
functions.
Fixes the following exception on K64F and other HW which can make
use of offloaded network HW:
FATAL: ***** Reserved Exception ( -16) *****
FATAL: r0/a1: 0x00000010 r1/a2: 0x0000644f r2/a3: 0x00000000
FATAL: r3/a4: 0x00000000 r12/ip: 0x2000474c r14/lr: 0x0001475b
FATAL: xpsr: 0x00000000
FATAL: Faulting instruction address (r15/pc): 0x0001b1cd
FATAL: >>> ZEPHYR FATAL ERROR 0: CPU exception
FATAL: Current thread: 0x20004c4c (unknown)
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/18957
Signed-off-by: Michael Scott <mike@foundries.io>
Corrected the amount of bytes copied for port handling in parse_ipv6
to prevent reading past the boundaries of the input string.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Add new RD Client API of lwm2m_rd_client_stop() for this
Fix issues of de-register and event reporting in RD Client
Signed-off-by: Jun Qing Zou <jun.qing.zou@nordicsemi.no>
The LwM2M implementation for DNS resolving has checks which
configure hints based on whether IPv4 or IPv6 are enabled.
Neither of them need enabled if using NET_SOCKETS_OFFLOAD,
which then causes an error to be returned to due to
"hints.ai_family" not being set.
Also the offload API need to know when to free the allocated
"struct addrinfo" instead of calling free() generically,
thus let's use the freeaddrinfo() API for sockets which will
call into the offload API if needed.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/18765
Signed-off-by: Jun Qing Zou <jun.qing.zou@nordicsemi.no>
When the firmware_pull mechansim sends the callback to notify the
sample of a new firmware block, the user supplied buffer can be
smaller than the CoAP BLOCK_SIZE setting. To handle this case,
we loop through the payload and fill the user supplied buffer with
smaller chunks.
Unfortunately, the last_block calculation is done outside this loop
which causes several callbacks (while in this loop) to have
last_block true. Let's fix this by adding a small check to make
sure we're at the end of the current payload block before notifying
the user of a last_block.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/16158
Signed-off-by: Michael Scott <mike@foundries.io>
The mDNS packet receive had issues:
* The DNS id needs to be 0 for both sending and receiving, we did
not accepted 0 incoming id.
* The mDNS response does not have any questions in it so we just
need to skip the question count checks in response.
* Skip the Cache-Flush bit in Class field so that we can properly
parse CLASS_IN value.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In DNS server init, print information whether the DNS server
is mDNS or LLMNR one. This way we do not need to remember what
IP addresses are used either of them.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The source UDP port in all Multicast DNS responses MUST be 5353
as described in RFC 6762 chapter 6.
Fixes#18732
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure we use the IPv4 event command when checking IPv4 address
add or delete instead of event mask.
Coverity-CID: 203483
Fixes#18400
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When val1 is 0, we need to handle a negative val2 value so that we
generate correct TLV value.
Example: val1 = 0, val2 = -500000 is equivalent to -0.5 decimal.
Currently we generate: 0.5 (losing the sign).
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/16154
Signed-off-by: Michael Scott <mike@foundries.io>
Current JSON formatting for float32/64 is broken in a similar way as
plain text. Let's use the newly fixed logic for plain text to
generate the float32/64 values in the JSON string.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/16154
Signed-off-by: Michael Scott <mike@foundries.io>
We can use the plain text float32/64 formatter for JSON as well, so
let's expose the put_float32/64 functions.
Signed-off-by: Michael Scott <mike@foundries.io>
Formatting a float32/64 value for plain text is broken.
Example for 32bit: val1=0 and val2=500000 is equivalent to 0.5
Current formatter was using %d.%d (%lld.%lld for 64bit) so
exported value was 0.500000 (or 0.5)
To fix this, for val2 use a zero-padded formatter for the maximum
length of each bit length (6 for 32bit and 9 for 64bit), and then
remove the zero characters at the end of the string.
Notes re: handling of val1/val2 signs:
- eliminate potential negative sign when converting val2 to avoid:
a value like: 0.-5
- use negative val2 when val1 is 0 to fix small negative handling
such as -0.5
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/16154
Signed-off-by: Michael Scott <mike@foundries.io>
Do not try to memcpy() the same buffer to itself.
This one also reverts commit 112ecb7290
("net: gptp: Fix for coverity CIDs 203471 and 203464") as that
did not fully fix the issue.
Coverity-CID: 203464
Coverity-CID: 203471
Fixes#18394
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that the extension, like HBHO, sub-option length is
not too large.
Fixes#16323
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When the bootstrap support was added, it looks like I somehow missed
the handling block in the engine.
Let's add it now to fix boostrap support.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/18080
Signed-off-by: Michael Scott <mike@foundries.io>
- LWM2M_SECURITY_INSTANCE_COUNT wasn't following the standard of
having the unconditional default in the last position
- LWM2M_SERVER_INSTANCE_COUNT needs another instance when
bootstrap is enabled.
Signed-off-by: Michael Scott <mike@foundries.io>
LwM2M boostrap support is enabled via the config option:
LWM2M_RD_CLIENT_SUPPORT_BOOTSTRAP. If enabled, this config sets
the default # of server and security instances. However, this is
not working correctly because LWM2M_RD_CLIENT_SUPPORT_BOOTSTRAP
is defined below it's uses in the Kconfig file.
Let's move the RD_CLIENT configs higher in the Kconfig to fix this
behavior.
Signed-off-by: Michael Scott <mike@foundries.io>
If no challenger went to replace the best port/vector, then the best
port is still the global_ds and thus point to the same memory: no need
to update the global_ds then.
Coverity-CID: 203471
Coverity-CID: 203464
Fixes#18395
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Looks like the logic to count rejection is missing. Removing count_rej
variable, and set a comment about initializing the code to the right
value once this logic will be in.
Coverity-CID: 203514
Fixes#18398
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Simplify algorithm to skip (aka calculate length) of encoded domain
name in a DNS answer. Now it's fully compliant to RFC 1035 regarding
handling of compressed FQDNs. Additionally, bounds checking is now
performed by the parsing code.
Fixes: #18334
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Let's use IS_ENABLED() instead of the #ifdef to get clearer code. ret
variable is used only at one place, no need for the ARG_UNUSED()
Coverity-CID: 203397
Fixes#18419
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Let's use IS_ENABLED() instead of the #ifdef to get clearer code. ret
variable is used only at one place, no need for the ARG_UNUSED()
Coverity-CID: 203468
Fixes#18420
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
IPv4 connection management status is stored in wrong
variable. ip_state should hold the status and then
it should be stored in state variable.
Fixes#18253
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When checking for total IP address counts, don't check
CONFIG_NET_IF_MAX_IPV6_COUNT twice. This was a typo for
CONFIG_NET_IF_MAX_IPV4_COUNT.
This was reported by IRC user: retfie
Signed-off-by: Michael Scott <mike@foundries.io>
This commit changes the Link-Layer Address Option length calculation
from hardcoded values to a numerical rounding up to full 8.
The length is calculated according to rfc4861 section 4.6.1.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
If the UDP socket is connected, then allow the user to leave
out the remote address in msghdr struct.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
- Commands were not gathered with the right macro
- bus fault access due to wrong declaration of iface_states external
variable.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The network to host byte order conversion is actually in place
on the network buffer. This prevents the reuse and forwarding of
RA packets. This commit uses temporary variables instead.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit adds support for a 6LoCAN Ethernet border translator.
CAN frames with the translator CAN address are translated and forwarded
to Ethernet. Ethernet frames with the first 34 bits matching the MAC
address of the translator are translated and forwarded to 6LoCAN.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Take the targer link layer address option link laxer addres lenght
from net packets source addres instead if the interface.
This is usefull for 6LoCAN border translator (6LoCAN to Ethernet).
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit implements net_pkt_shallow_clone. A shallow clone clones
the net_pkt but not the buffers. The buffers are only referenced and
therefor only freed when both copies of the net_pkt are freed.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commits adds support for reception of packets thats comes from
a Ethernet to 6LoCAN translator. This packets carry the Ethernet
MAC address (6 bytes) inline in the FF (First Frame).
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit is an implementation of 6LoCAN, a 6Lo adaption layer for
Controller Area Networks. 6LoCAN is not yet standardised.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>