This patch enables the GPIO driver by default on all boards equipped
with an nRF SoC (all boards having `CONFIG_SOC_FAMILY_NRF=y` in their
`_defconfig` file).
In vast majority of cases the driver is needed, so it is more
convenient to enable it at board level than in particular
applications.
And if the driver is undesired for some reason, it can be still
disabled in the application config.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add the bt-mon-uart chosen node to all the nRF-based boards so that they
can all use CONFIG_BT_DEBUG_MONITOR without additional changes.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fixes the apds9960 i2c address on the reel_board. Found while converting
the apds9960 driver to use the i2c address from device tree rather than
a hardcoded value in apds9960.h.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The current flash configurations for all nRF52840's in Zephyr is
VERY constrained when it comes to allowing samples any space for
storage or custom areas. It only leaves the last 4 pages of flash
for "storage".
The nRF52840 is also capable of using OpenThread which defaults
to using the last 4 pages of flash for storing OpenThread-related
network data.
This means that while using OpenThread under any configuration
designed to use mcuboot partition slots, there is no space left
over for storage of any kind.
Let's adjust the partition table to set storage at 8 pages of
flash (32k). This fixes the conflict with OpenThread and leaves
room for future use cases that may arise.
Signed-off-by: Michael Scott <mike@foundries.io>
A new role :zephyr_file: is available that renders to a link to the file
or folder in GitHub. Find appropriate references using :file: and
convert to :zephyr_file: to take advantage of its linking capability.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The creation of the udev rule requires the user to be root else
it will fail. Update the text of the documentation to make it clearer
and change the shell prompt of the command to '#'
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Enable pull-up on UART RX pin to reduce power consumption.
If the board is powered by battery and the debugger is
not connected via USB to the host, the SoC consumes up
to 2mA more than expected.
The consumption increases because RX pin is floating
(High-Impedance state of pin B from Dual-Supply Bus Transceiver).
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Be consistent in how board docs are named and move all to index.rst.
This will make the URL to the board documentation predictable and easier
to remember.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The phrase "Zephyr applications use the ..." in many boards and
inconsistently. This is just to say what is the board identify is.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The values for the registers like GDV, SDV and Boarder Waveform
depend on the panel and display controller. Add DT properties
and obtain such values from DT.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
From the driver point of view, monochrome controllers from the ssd16xx
family mostly differ by the amount of row and columns that are
supported. If they support more than 256 rows and/or columns the
corresponding size or position is sent using 2 bytes instead of 1 byte.
This patch therefore adds the width-bits and height-bits DT properties
to make this configurable.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
As we want to remove dts dependency on Kconfig, we had a case based on
CONFIG_BOOTLOADER_MCUBOOT. From a DTS point of view that was just
getting the chosen property 'zephyr,code-partition' set. We can easily
move this to the actual dts files and remove the mcuboot.overlay.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert ssd1673 display driver to use new defines so we can remove
the dts_fixup.h code for it. Also dropped "-spi" from compatible.
Fix up references in reel_board dts and sample.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The schematic shows that both INT1 & INT2 from the MMA8652FC are wired
up, update the dts to reflect this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The options selecting nRF drivers are now enabled by default when
an nRF SoC is selected as the build target.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Reel Board doesn't enable BT by default like many of the nRF52
boards do. So let's make enabling BT a bit easier, by selecting
the BT_CTLR config when BT is enabled. This allows a sample
overlay to merely set:
CONFIG_BT=y
And the end result should be close to correct.
Signed-off-by: Michael Scott <mike@foundries.io>
Including Bluetooth to every project unnecessary increase size of the
project, for example hello world sizes:
Memory region Used Size Region Size %age Used
FLASH: 48492 B 1 MB 4.62%
SRAM: 11236 B 256 KB 4.29%
IDT_LIST: 136 B 2 KB 6.64%
after the patch:
Memory region Used Size Region Size %age Used
FLASH: 13344 B 1 MB 1.27%
SRAM: 4004 B 256 KB 1.53%
IDT_LIST: 72 B 2 KB 3.52%
3+ times difference.
PS: It also crashes when 802.15.4 enabled.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Remove the ifdef related to CONFIG_FS_FLASH_STORAGE_PARTITION. There
shouldn't be any harm in always having the partition around as we'll
just generate the defines related to and most applications will ignore
them.
Helps get one step closer to have DTS not depend on Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We should let drivers or board code include soc.h directly so we can keep
board.h to local info for board specific code.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove some references <board.h> that aren't need or replace them with
<soc.h> where that is the proper include to pull in. Also use "board.h"
instead of <board.h> for how we include the file when its local to the
board code itself.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In an effort to reduce the number of CONFIG_ defines in dts files, we
can remove CONFIG_MCUMGR_SMP_UART and just always set
'zephyr,uart-mcumgr' as there is no harm to always having this set for
those board dts files that define the property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There were several issues in the dts binding for the ssd1673 display:
* binding file mixed description & generation up together
* Use of BASE_LABEL
* orientation-flipped should have been of type boolean
Update the binding file to reflect these changes, and made associated
changes to dts_fixup.h and driver as needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Flashing the board as described in the docs does not work without having
proper udev rules set. Add documentation for setting those.
Signed-off-by: Johannes Hutter <johannes@proglove.de>
Add a link to the reel board product page at PHYTEC to help people in
locating schematics, etc.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This patch is equivalent to 7b0ce85242,
but applied to buttons. As stated in the previous commit message:
This change aims at fixing 'unit_address_vs_reg' warning in arm based
boards. This warning pops up when a node name is made up with an
address (node_name@xx) but does not contain a reg property. This case
was encountered for led nodes for instance, where a reg property has
no meaning. Fix this by changing node_name@xx to node_name_xx which
removes the guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This patch is equivalent to 7b0ce85242,
but applied to more boards. As stated in the previous commit message:
This change aims at fixing 'unit_address_vs_reg' warning in arm based
boards. This warning pops up when a node name is made up with an
address (node_name@xx) but does not contain a reg property. This case
was encountered for led nodes for instance, where a reg property has
no meaning. Fix this by changing node_name@xx to node_name_xx which
removes the guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Every board that uses dts-enabled gpio drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_GPIO_DEVICE and
HAS_DTS_GPIO.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled i2c drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_I2C_DEVICE and
HAS_DTS_I2C.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch changes the behavior of the sensor. The sensor
will remain in sleep mode after initialization and will only
run the measurements once when sample_fetch is called.
This optimizes the power consumption of the sensor as it
stays in sleep mode most of the time.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The ARM_MPU_NRF52X option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the ARM_MPU_NRF52X option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_NRF51822_QFAA
CONFIG_SOC_NRF51822_QFAB
CONFIG_SOC_NRF51822_QFAC
CONFIG_SOC_NRF52810_QFAA
CONFIG_SOC_NRF52832_QFAA
CONFIG_SOC_NRF52832_CIAA
CONFIG_SOC_NRF52832_QFAB
CONFIG_SOC_NRF52840_QIAA
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
UART pins (TX, RX, RTS, CTS) are now configured in DTS files.
RTS and CTS definitions are optional. If flow control is enabled
and RTS/CTS pins are not defined, then compiler will issue
an error message.
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
This change adds DTS definition of SPI device for nRF chips.
It also removes SPI pin configuration from Kconfig and moves it to
chip DTS.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
When I2C and SPI are not used (such as when building a simple
bootloader for this target), the current Kconfig is generating a fair
bit of warning spew. Clean it up by moving some explicit _defconfig
settings into defaults.
Signed-off-by: Marti Bolivar <marti@foundries.io>
PR #8729 removed the old GPIO_NRF5 driver in favor of an
nrfx-based one. The reel_board still references the old one,
causing CI failures.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>