The OPENSDA_FW and LPCLINK_FW cmake variables are remnants of pre-west
days where we used an environment variable to set the desired debug host
tool, such as jlink or pyocd, based on which debug probe firmware was
loaded on the board. We now have two possible ways to do this, neither
of which requires the nxp-specific OPENSDA_FW or LPCLINK_FW variables:
1. Set standardized cmake runner variables when generating the build
system:
$ west build -- -DBOARD_FLASH_RUNNER=jlink -DBOARD_DEBUG_RUNNER=jlink
2. Use the west "--runner" argument with the debug and flash commands:
$ west debug -r jlink
Remove the now unnecessary OPENSDA_FW ond LPCLINK_FW variables and
update board documentation accordingly.
A few boards (frdm_kw41z, hexiwear_k64, mimxrt10{20,50,60,64}_evk)
reordered pyocd.board.cmake and jlink.board.cmake includes to preserve
the default runner when OPENSDA_FW was not explicitly set.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes pwm pinmuxes on CONFIG_PWM for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes adc pinmuxes on CONFIG_ADC for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes i2c pinmuxes on CONFIG_I2C for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes spi pinmuxes on CONFIG_SPI for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes serial pinmuxes on CONFIG_SERIAL for all nxp boards
(kinetis, lpc, and imx families) to avoid possible conflicts between
peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Once the TPM driver and the required configs have been added,
now this patch enables the usage of the PWM framework on KW41Z
SoCs. As such, the DTS gets the proper nodes and the pinmuxing
is done according to the configuration requested.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
The Kconfig I2C_[0-9] sybmols don't have any meaning for the majority of
SoCs. The drivers doesn't utilize them and no sample or test code does
either so we can remove setting them in board Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. As part of this conversion we
remove the Kconfig options for per GPIO controller enables and instead
get that information from device tree. This means we now disable each
GPIO controller by default in the DTS and have each board dts enable the
GPIO controller ports it needs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove all "supported: -hwinfo" definitions from the boards
yaml files and documentation. hwinfo can generally be tested
on every board because it returns -ENOTSUP if not supported.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
In order to overrdie a choice one needs to define it again. Override it
by redefining it in the .defconfig file.
See #22474.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The Kconfig board choice only has only one option which is implicitly
enabled, therefore it is not necessary to set the symbol explicitly in
board defconfigs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts the fxos8700 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on frdm_k64f and rv32m1_vega_ri5cy boards. The latter verifies
that the reset output works correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on frdm_k64f board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all kinetis socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a device tree nexus node to define which gpio pins are mapped from
the soc to the arduino header.
The frdm_kw41z board excludes the arduino A0 pin because it cannot be
muxed as a gpio on the soc.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Sorts the list of supported features in alphabetical order for all nxp
boards. No features are added or removed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
1) Add cryptographically secure random functions to provide
FIPS 140-2 compliant random functions.
2) Add name to random function choice selectors to ease
selection in SOC .defconfig files
3) Add bulk fill random functions.
Signed-off-by: David Leach <david.leach@nxp.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Instead of having a mix of west and CMake/ninja instructions for
building and flashing, document it using only west. This will help
clarify that west is the default build tool in Zephyr and should also
reduce confusion over what tool to use.
Note that the biggest change is changing the default in
doc/extensions/zephyr/application.py for :tool:, from all to west.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Clean up some stray references to cmake in doc, boards and
samples that don't make explicit use of the zephyr app extension,
as well as other minor doc fixes.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This helps by letting us add checks for when the runner has already
been set. There is documentation saying you can set
-DBOARD_DEBUG_RUNNER at the command line and have it take effect,
which turns out not to be true for a large number of boards.
A status message helps the user debug.
(We'll address the existing in-tree boards in the next patch.)
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The frdm_kw41z board was originally configured in zephyr to use the
jlink runner by default because pyocd didn't yet support the kw41z soc.
Support for kw41z was added in pyocd v0.9.0, so we can now default to
daplink firmware and pyocd.
Now all freedom boards in zephyr consistently use daplink and pyocd.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the programming and debugging section in the freedom board
documents to leverage the new debugging guide covering debug probes and
host tools.
These boards support OpenSDA DAPLink and OpenSDA J-Link onboard debug
probes. They can also support an external J-Link probe, but this
requires board modifications (cutting traces) and is therefore not
documented.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Be consistent in how board docs are named and move all to index.rst.
This will make the URL to the board documentation predictable and easier
to remember.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Since Voltage Reference block is not supported, the ADC does not work
properly on FRDM-KW41Z. Set voltage reference to alternate source
in frdm_kw41z_defconfig.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Fixes broken user guide and schematics links in nxp board documentation.
Updates remaining nxp.com links from http to https.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
