This commit adds the PWM LED definition in the board device tree for
the on-board LED connected to the pin PC18.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Utilize the devicetree property "zephyr,random-mac-address" to determine
if a driver should use a random mac address and remove the associated
Kconfig options that enabled this feature.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the asynchronous UART API testing support on the SAM
E54 Xplained Pro board.
The SERCOM1 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM1 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the `i2c-0` alias for the Atmel SAM E54 Xplained Pro
board, as required by the I2C test.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The OpenOCD JTAG reset causes the SAM E54 SoC to prematurely start code
execution before the SoC is ready, and this causes hard faults when the
MPU is enabled -- causing OpenOCD to hang.
This commit disables the JTAG SRST reset mechanism and falls back to
using the Cortex-M SYSRESETREQ emulation reset mechanism, which does
not have experience this issue.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit enables the ARM memory protection unit for the SAM D54
Xplained Pro board, since `CPU_HAS_ARM_MPU` is now selected by the SoC
Kconfig.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit enables the GMAC Ethernet support for the `atsame54_xpro`
board which includes an on-board RMII PHY.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
In order to use its serial peripheral SERCOMs SAMD socs require their
pins to be configured with pinmux. Currently pins are muxed only for the
boards' default serial interfaces. The pinmux code is written to throw
a compiler error if a user tries to use any sercom in a way it wasn't
pre-defined to be used.
This commit changes compiler errors to warnings so that user can provide
custom pinmuxing code in their app.
Fixes#23133
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on sam_e70_xplained board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This adds support for the Atmel SAM E54 Xplained Pro Evaluation Kit.
Only basic functionality has been tested so far.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
