added and began work on integrating failsafe_detect_threshold
got rid of acc_lpf_for_velocity since that seemed no longer used.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@317 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
PWM and ADC configuration is the same as the naze32 for now. Requires an accelerometer is connected via I2C2.
I2C signals SDA2 and SCL2 are on the UEXT header (Pins 6 and 5 respectively)
USART signals TX and RX are on the CON3/CON4 headers (TX = D7, RX = D8)
Onboard LEDs (LED1/LED2) working.
Buzzer support removed for now as it conflicted with PWM map and LEDs.
mma845x support disabled as it conflicted with an LED.
Relocated some NAZE specific comments.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@302 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
Conflicts:
src/board.h
src/main.c
Conflicts:
src/main.c
PWM and ADC configuration is the same as the naze32 for now. Requires an accelerometer is connected via I2C2.
I2C signals SDA2 and SCL2 are on the UEXT header (Pins 6 and 5 respectively)
USART signals TX and RX are on the CON3/CON4 headers (TX = D7, RX = D8)
Onboard LEDs (LED1/LED2) working.
Buzzer support removed for now as it conflicted with PWM map and LEDs.
mma845x support disabled as it conflicted with an LED.
Relocated some NAZE specific comments.
Disabling PWM2 as an input as it conflicts with the yellow onboard LED2.
PWM and ADC configuration is the same as the naze32 for now. Requires an accelerometer is connected via I2C2.
I2C signals SDA2 and SCL2 are on the UEXT header (Pins 6 and 5 respectively)
USART signals TX and RX are on the CON3/CON4 headers (TX = D7, RX = D8)
Onboard LEDs (LED1/LED2) working.
Buzzer support removed for now as it conflicted with PWM map and LEDs.
mma845x support disabled as it conflicted with an LED.
Relocated some NAZE specific comments.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@302 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
defaulted to looptime of 3500 (yea, yea)
rewrote baro stuff to match mwc2.2 - both supported sensors now return temperature and pressure, which is used in altitude calculation code
rewrote hmc5883 driver to include calibration inside the driver file instead of calling parts of calibration from userspace. it will now blink LED1 while calibrating
some parts remaining to do.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@298 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
mw2.2-merged stuff:
* implemented profiles 0-2 (called 'setting' in mwiigui)
* merged in MSP changes including profile switch
* cleaned up rc / aux switch stuff in mw.c based on 2.2 rewrite
* main loop switch for baro/sonar shit adjusted
todo: basically the rest of 2.2 changes (i think some minor imu/gps/baro updates)
baseflight-specific stuff:
* made boxitems transmission dynamic, based on enabled features. no more GPS / camstab trash if it's not enabled
* cleaned up gyro drivers to return scale factor to imu code
* set gyro_lpf now controls every supported gyro - not all take same values, see driver files for allowed ranges, in case of invalid lpf, defaults to something reasonable (around 30-40hz)
maybe couple other things I forgot. this is all 100% experimental, untested, and not even flown. thats why there's no hex.
merge is still ongoing.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@294 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added sending cell voltages (faked) via frsky telemetry by fiendie
two additional cli commands (aux and dump) from jef79m - aux allows setting switches from command line, dump creates a copy-pasteable config which can be sent to a new board.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@283 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
cleaned up frsky telemetry a bit with verbose telemetry ID names, changed loop timing a bit, added output for heading and voltage (when vbat is enabled). telemetry stuff is untested, so someone try it out.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@226 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
status in cli now prints cpu MHz, 72 when running off crystal, 64 when running off intrc.
corrected WHO_AM_I check for mpu6050 when it's used on alternate address (AD0 high).
corrected PWM driver to consider CPU clock for timer prescalers - now things properly work below 72MHz
added a neat hack for pitch angle calculation so that it's not affected when roll reaches 90deg
added proper math for vector rotation instead of small-angle approximation
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@225 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
fixed pwm init for airplane mode mistakenly deleting motors from the mix. flyingwing should really work now.
removed led debug from althold
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@223 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
