4057605178
Enables the ft5336 touch controller interrupt on the mimxrt1050_evk board. Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
158 lines
3 KiB
Plaintext
158 lines
3 KiB
Plaintext
/*
|
|
* Copyright (c) 2017, NXP
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include <nxp/nxp_rt.dtsi>
|
|
|
|
/ {
|
|
model = "NXP MIMXRT1050-EVK board";
|
|
compatible = "nxp,mimxrt1052";
|
|
|
|
aliases {
|
|
led0 = &green_led;
|
|
sw0 = &user_button;
|
|
kscan0 = &touch_controller;
|
|
};
|
|
|
|
chosen {
|
|
zephyr,console = &lpuart1;
|
|
zephyr,shell-uart = &lpuart1;
|
|
};
|
|
|
|
sdram0: memory@80000000 {
|
|
/* Micron MT48LC16M16A2B4-6AIT:G */
|
|
device_type = "memory";
|
|
compatible = "mmio-sram";
|
|
reg = <0x80000000 0x2000000>;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
green_led: led_0 {
|
|
gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
|
|
label = "User LD1";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
user_button: button_0 {
|
|
label = "User SW8";
|
|
gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
arduino_header: connector {
|
|
compatible = "arduino-header-r3";
|
|
#gpio-cells = <2>;
|
|
gpio-map-mask = <0xffffffff 0xffffffc0>;
|
|
gpio-map-pass-thru = <0 0x3f>;
|
|
gpio-map = <0 0 &gpio1 26 0>, /* A0 */
|
|
<1 0 &gpio1 27 0>, /* A1 */
|
|
<2 0 &gpio1 20 0>, /* A2 */
|
|
<3 0 &gpio1 21 0>, /* A3 */
|
|
<4 0 &gpio1 17 0>, /* A4 */
|
|
<5 0 &gpio1 16 0>, /* A5 */
|
|
<6 0 &gpio1 23 0>, /* D0 */
|
|
<7 0 &gpio1 22 0>, /* D1 */
|
|
<8 0 &gpio1 11 0>, /* D2 */
|
|
<9 0 &gpio1 24 0>, /* D3 */
|
|
<10 0 &gpio1 9 0>, /* D4 */
|
|
<11 0 &gpio1 10 0>, /* D5 */
|
|
<12 0 &gpio1 18 0>, /* D6 */
|
|
<13 0 &gpio1 19 0>, /* D7 */
|
|
<14 0 &gpio1 3 0>, /* D8 */
|
|
<15 0 &gpio1 2 0>, /* D9 */
|
|
<16 0 &gpio3 13 0>, /* D10 */
|
|
<17 0 &gpio3 14 0>, /* D11 */
|
|
<18 0 &gpio3 15 0>, /* D12 */
|
|
<19 0 &gpio3 12 0>, /* D13 */
|
|
<20 0 &gpio1 1 0>, /* D14 */
|
|
<21 0 &gpio1 0 0>; /* D15 */
|
|
};
|
|
|
|
panel {
|
|
compatible = "rocktech,rk043fn02h-ct";
|
|
port {
|
|
lcd_panel_in: endpoint {
|
|
remote-endpoint = <&lcd_panel_out>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
arduino_serial: &lpuart3 {};
|
|
|
|
&flexspi {
|
|
reg = <0x402a8000 0x4000>, <0x60000000 0x4000000>;
|
|
hyperflash0: hyperflash@0 {
|
|
compatible = "cypress,s26ks512s";
|
|
reg = <0>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&lcdif {
|
|
status = "okay";
|
|
port {
|
|
lcd_panel_out: endpoint {
|
|
remote-endpoint = <&lcd_panel_in>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&lpi2c1 {
|
|
status = "okay";
|
|
|
|
fxos8700@1f {
|
|
compatible = "nxp,fxos8700";
|
|
reg = <0x1f>;
|
|
label = "FXOS8700";
|
|
|
|
/* Two zero ohm resistors (R263 and R264) isolate sensor
|
|
* interrupt gpios from the soc and are unpopulated by default.
|
|
* Note that if you populate them, they conflict with LCD and
|
|
* Ethernet interrupt gpios.
|
|
*/
|
|
int1-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
|
|
int2-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
touch_controller: ft5336@38 {
|
|
compatible = "focaltech,ft5336";
|
|
reg = <0x38>;
|
|
label = "FT5336";
|
|
int-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
&lpuart1 {
|
|
status = "okay";
|
|
current-speed = <115200>;
|
|
};
|
|
|
|
&lpspi3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&enet {
|
|
status = "okay";
|
|
ptp {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&usb1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usdhc1 {
|
|
status = "okay";
|
|
pwr-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
|
|
cd-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
|
|
};
|