Instead of selecting DTS overlay based on platform name
use FILE_SUFFIX in dual_uart and cross_domain test variants.
Add overlays required to run the uart_elementary tests on nrf54lm20b.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
- Updates the button pin and port
- Adds one more button which is present on the board
- Enables portd for the usage of the same
Signed-off-by: Muhammed Asif <muhammed.asif@microchip.com>
- Adds the device tree node of external interrupt controller for
pic32cx_sg common dtsi file
Signed-off-by: Muhammed Asif <muhammed.asif@microchip.com>
Increase the number of MPU regions for nsim_em7d_v22 from 8 to 16
to match other ARC EM boards (nsim_em, nsim_em11d) and enable
userspace memory domain tests that require more partition regions.
With only 8 MPU regions, after allocating static regions and thread
stack regions, only 3 regions remained for memory domain partitions,
causing tests like samples/userspace/shared_mem to fail.
Increasing to 16 regions provides sufficient capacity for userspace
tests and improves test coverage on this board.
Signed-off-by: Mohamed Moawad <moawad@synopsys.com>
Add Realtek rtl8752h chip and driver device tree files.
Signed-off-by: Zophai Liu <zophai_liu@realsil.com.cn>
Signed-off-by: Yuzhuo Liu <yuzhuo_liu@realsil.com.cn>
Add scheduled scan apis support for supplicant.
Add kconfig options to set default iteration and scheduled scan
min interval.
Signed-off-by: Fengming Ye <frank.ye@nxp.com>
Fix condition to initialize ramcfg device for stm32N6xx AXISRAM
configuration as IF_ENABLED() requires a evaluated value of 1
as positive case.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Include clock config headers instead of manually configuring
the clock muxes for every Series 2 radio board.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Add include files for each clock source to configure the
devicetree to use that source. This simplifies clock configuration
to including the correct header, rather than manually modifying
every mux to select the given source.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
This commit deletes the mpr sensor sample as it is completely
redundant with the pressure_polling sample.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Resume from cli->block.number instead of block 0,
so BLOCK_START matches the server's current block.
Blob client does not drop server due to this anymore.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Accept WAITING_FOR_CHUNK phase on resume
when server responds SUCCESS
(server's XFER_START idempotency path).
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
The initialization priority was hardcoded to 0. However, the initialization
takes a relatively long time (1 to 2 seconds on RW612). With this change,
the initialization priority properly follows CONFIG_ETH_INIT_PRIORITY.
Signed-off-by: Sebastiaan Merckx <sebastiaan.merckx@verhaert.com>
Address of the event endpoint was read before GPIOTE pin was configured
with the exact GPIOTE channel so endpoint address was invalid and PPI
connection did not work. Bug introduced when porting to nrfx 4.0:
ad1e5ac253 ("nordic: update and align to nrfx 4.0.1").
Addded handling of GPIO retaining which is needed when pins are handled
without GPIO driver.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Introduce documentation for using CLUTGen, a C look-up table generator
as an external module into Zephyr.
This module adds a preview build target and a cmake function that can be
used on the app CMakeLists.txt and links the generated LUTs into the
application, so the user can easily integrate into any existing or new
projects.
Signed-off-by: Paulo Santos <pauloxrms@gmail.com>
Move the following Kconfig options, which depend on
MBEDTLS_BUILTIN, from Kconfig to Kconfig.mbedtls:
- MBEDTLS_SSL_MAX_CONTENT_LEN
- MBEDTLS_MEMORY_DEBUG
- MBEDTLS_DEBUG_C
- MBEDTLS_ZEROIZE_ALT
Move MBEDTLS_SSL_DTLS_CONNECTION_ID within Kconfig.mbedtls to a more
suitable place.
Move MBEDTLS_INSTALL_PATH within Kconfig to a more suitable place too.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Only depend on MBEDTLS_BUILTIN, not MBEDTLS_CFG_FILE.
We can have scenarios where MBEDTLS_BUILTIN is used but with a different
configuration file that still leverages the existing Kconfig options.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
It was just used to decide whether to make CONFIG_MBEDTLS_CFG_FILE
promptless.
We can just leave the prompt always enabled; the Kconfig option is
always visible anyway and has a sensible default value.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
It was not a standard Mbed TLS configuration.
Replace it by the underlying macros it used to enable:
MBEDTLS_PEM_PARSE_C, MBEDTLS_PEM_WRITE_C and MBEDTLS_BASE64_C
indirectly.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
To match its Mbed TLS configuration counterpart
(MBEDTLS_SSL_SERVER_NAME_INDICATION).
Also add its prerequisite as a Kconfig condition.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Add a dedicated Kconfig option for this previously hidden and
automatically enabled Mbed TLS configuration.
Make the relevant key exchange Kconfig options depend on it.
Enable it explicitly where needed.
Fix the condition for defining MBEDTLS_X509_USE_C (based on
mbedtls_config.h).
Check for CONFIG_MBEDTLS_X509_CRT_PARSE_C instead of
MBEDTLS_X509_CRT_PARSE_C now that we have a Kconfig option for it.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Replace it by the standard Mbed TLS configuration.
The enabling of MBEDTLS_SELF_TEST is removed too as it's gone with
Mbed TLS 4.0.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
It's a standard Mbed TLS configuration. It should not
depend on CONFIG_MBEDTLS_BUILTIN.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Add shield definition for the MikroElektronika EEPROM 13 Click shield,
an mikroBUS compatible evaluation module for the STMicroelectronics
M24M01E (1M-bit) I2C Serial EEPROM chip.
Tested with the command mentioned on the index.rst page.
Signed-off-by: Stephan Linz <linz@li-pro.net>
The litex bootloader doesn't support XIP by default,
so remove it. In the board it was already deactivated.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Instead of reading the CCID and then using
bt_tbs_client_get_by_ccid to get the instance to provide the handles
event, we can now just use bt_tbs_client_get_by_index directly.
This also changes so that the upper tester will receive a
handles event for each instance, and not just for GTBS.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add function to get an instance pointer by index.
This works the same as bt_tbs_client_get_by_ccid except that
it uses the index instead of the CCID.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Show how to run pytest tests without rebuilding by using the
twister_pytest_config.yaml file generated by Twister. Update
integration description to reflect YAML configuration approach.
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
Update unit tests to verify YAML-based parameter serialization instead
of CLI arguments. Add tests for twister config file parsing and update
existing tests to check pytest_params object and YAML output.
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
Add comprehensive YAML configuration support for pytest-harness
integration, replacing CLI argument approach with structured
configuration files while maintaining backward compatibility.
Key changes:
- Add --twister-config option to load test parameters from YAML
- Refactor TwisterHarnessConfig to support CLI and YAML configuration
- Move pytest parameter generation from CLI args to config files
This enables more flexible test configuration through structured YAML
files and improves the overall architecture of pytest-twister
integration.
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
