Uses sub-partitions to allow having a dedicated secure and
non-secure partition area in flash partitions, which also allows
the main application slot to be extended when TF-M is not in use
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Align all sensor drivers that are using stmemsc (STdC) HAL i/f
to new APIs of stmemsc v2.9.1.
Requires https://github.com/zephyrproject-rtos/hal_st/pull/25
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Remove XIP dependency for enabling memory mapping for Q/O/XSPI NOR Flash.
It is not necessary and is preventing configuring an external Flash in
memmap mode if there is no internal Flash (like on STM32N6)
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
In case the receiving packet socket is not bound to any specific
interface, or is explicitly bound to "any" interface (at index 0),
it should collect packets from all interfaces. Add test cases which
verify that.
Also, if a packet socket is bound to a specific interface, it should not
receive packets from others. Add a test case to verify that as well.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The recvfrom test case for DGRAM packet socket specified wrong socket
type, so RAW sockets were tested twice instead. Also, for the DGRAM
variant, the offset was not taken into account for the expected packet
length.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Default binding should take place before we actually make use of the
local address when registering packet socket "connection".
Also, instead of hard coding the protocol for default binding to
ETH_P_ALL, use the protocol that the socket was created with.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In order to be able to receive packets on unbound packet sockets (which
should collect packet from all interfaces in such case), it's needed to
register receive callback at the socket layer as soon as the socket is
created.
In additional to that, the default binding for packet sockets need to be
revisited. Packet socket should not be bound to the default interface,
as this way the socket would only be receiving packets from that
particular interface. Instead, leave the interface unspecified in such
case.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Allow to update the local address on a registered connection when
rebinding.
This is needed for packet sockets, as by default packet socket
will be bound to "any" interface (interface index 0), and interface
index is part of the local address registered for packet socket.
In order to be able to explicitly bind to a specific interface later, it
needs to be possible to update the local address registered for the
connection, as we need to update the interface index, which is used
by net_conn_packet_input() for packet filtering.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
add zephyr,mmc-disk's disk names as they were missing causing fatfs to
be unusable on boards that had otherwise valid DT configuration for
the mmc disks.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
When the L2CAP channel connection is in none basic mode, the
`seg_recv` cannot work properly if the configuration
`CONFIG_BT_L2CAP_SEG_RECV` is enabled. And the L2CAP channel
connection will be broken incorrectly.
Check whether the received data len exceeds the SDU length if the
`SAR` is `BT_L2CAP_CONTROL_SAR_END` or `BT_L2CAP_CONTROL_SAR_CONTI`.
And check whether the SDU length is valid if the `SAR` is
`BT_L2CAP_CONTROL_SAR_UNSEG` or `BT_L2CAP_CONTROL_SAR_START`.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
- Updated airoc_mgmt_connect to be able use security provided
by user (params->security). If it is not passed, we will perform
scan ssid to detect secure type.
- Fix convert_whd_security_to_zephyr() with correct corresponding
whd_security_t to zephyr security type.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
The current shim driver for flash-nxp-s32-qspi returns invalid error
when handling write, erase operations with zero size.
This issue causes the failure of the tests/subsys/settings/fcb/.
Updated to ignore the flash operations with zero size instead of.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
The cap_initiator_broadcast_to_bap_broadcast_param function
did not properly relay the ISO test parameters from the CAP
parameters to the BAP parameters.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
alarm flags only need to be cleared if PORF flag is set; otherwise,
the RTC is already running and alarm flags must not be cleared
Signed-off-by: Vixay Phimmasane <visuphi@gmail.com>
Increase the value of CONFIG_MAIN_STACK_SIZE for the s32z270 board to
avoid stack overflow during the adc_api test, and add new .conf files
for each board.
Signed-off-by: Ha Duong Quang <ha.duongquang@nxp.com>
Some in-the-wild devices use SDU interval of 0 when BN == 0; This
is not allowed by BT Core Spec v6.0, but is not specifically
mentioned in v5.4 and earlier. To allow connecting a CIS to these
devices, relax the check on SDU interval
Note: LL/CIS/PER/BI-07-C only checks rejection of invalid SDU interval
with BN > 0, so it still passes with this change
Signed-off-by: Troels Nilsson <trnn@demant.com>
Providing a set of SQEs with varying delays in different orders. Test
validates each delay is completed at the right amount (and the CQEs are
received in the right order).
Signed-off-by: Luis Ubieda <luisf@croxel.com>
SQE items with this OP will take the specified amount of time
(asynchronously) before completing. This allows to serve as an
asynchronous delay in between SQE items (e.g: A sensor measurement
requested, which requires 50-ms before having the result available).
Signed-off-by: Luis Ubieda <luisf@croxel.com>
keep_alive_timer_restart() only works in ESTABLISHED state. In
tcp_in() SYN_SENT and SYN_RECEIVED state, it won't work by calling
this function. So remove the call in that 2 states while adding it
in the bottom after changing the conn->state to ESTABLISHED.
Signed-off-by: Shrek Wang <inet_eman@outlook.com>
The response L2CAP_COMMAND_REJECT_RSP(BT_L2CAP_REJ_NOT_UNDERSTOOD)
should be replied if the received L2CAP command is a invalid L2CAP
signaling command packets with extra data in the Information Payload.
Send L2CAP_COMMAND_REJECT_RSP(BT_L2CAP_REJ_NOT_UNDERSTOOD) if it a
small L2CAP signaling PDU or it has short length.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Introduces a driver for ST75256 Display Controller that
supports mono and greyscale but not i2c mode.
Signed-off-by: Camille BAUD <mail@massdriver.space>
According the specification, in extreme cases, the deviation of the APB
clock and LFCLK clock can reach up to +/-1% (+/- 10ms).
Therefore, exclude npcx platforms from the test because it required 1ms
accuracy.
fixes: #66185
Signed-off-by: Arkadiusz Cholewinski <arkadiuszx.cholewinski@intel.com>
The z_vrfy function for this syscall
```
__syscall int hwinfo_get_device_eui64(uint8_t *buffer);
```
in `drivers/hwinfo/hwinfo_handlers.c`, used an `ssize_t` rather than an
`int` which makes it inconsistent with the prototype declared in
`drivers/hwinfo.h`.
Use `int` instead of `ssize_t`.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
SoftAP operation needs around 5700 bytes of stack. With a
buffer of 100 bytes, set the supplicant stack size to 5800.
Signed-off-by: Ravi Dondaputi <ravi.dondaputi@nordicsemi.no>
Note the ability to upload custom data in the documentation, and add
it to the release notes.
Also include the new `CONFIG_ZPERF_SESSION_PER_THREAD` option.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Slightly increase the default maximum size for zperf uploads to support
1kB of data payload together with the 40 bytes UDP client header.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Add support for uploading custom data, instead of a static packet of
'z'. This can be used for more accurate profiling of uplink throughput
for a given application. For example, reading data from flash, or
application level encryption.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The timestamp in the UDP header is expected to be a Unix timestamp, not
an application uptime. Add the option to specify the Unix time at
function entry so that the reported timestamps are accurate.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The minimum packet size is the combination of the datagram and client
headers, not just the datagram header.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Add `--rtt-server` option to start RTT server when the OpenOCD
launched from `debug`, `debugserver`, and `attach` commands.
This option starts the RTT server and opens a port,
but RTT logging must be done externally.
That is, you must connect to port 5555 using `telnet` or `nc`
in another terminal to view the RTT log.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
The board provides an axp2101 chip with a builtin charger. We add the
corresponding charger node with values taken from the official XPowers
library example. This makes the board compatible with the
drivers/charger example.
[1] a7d06b98c1/examples/AXP2101_Charge_Example/AXP2101_Charge_Example.ino
Signed-off-by: Felix Moessbauer <felix.moessbauer@gmail.com>
