Added pmod_serial and pmod_header node labels to EK-RA8M1 device
tree board definition, allowing compatible shield boards to be used.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
Fixes: #78010
This commit adds the "Gateway Advertisement and Discovery" process
to the MQTT-SN Publisher Sample application.
Signed-off-by: Kenneth Witham <kennywitham4@gmail.com>
Fixes: #78010
This commit adds tests for the "Gateway Advertisement and Discovery"
process. This includes tests for handling SEARCHGW, GWINFO, and ADVERTISE
as well as manually adding a Gateway for use. Gateway pruning when
missing ADVERTISE messages is also tested.
Signed-off-by: Kenneth Witham <kennywitham4@gmail.com>
Fixes: #78010
This commit implements the "Gateway Advertisement and Discovery" process
defined in section 6.1 of the MQTT-SN specification.
This includes breaking changes to the transport interface and the default
included UDP interface implementation as support for UDP multicast
messages is added as implemented by the Paho MQTT-SN Gateway.
Signed-off-by: Kenneth Witham <kennywitham4@gmail.com>
This follows update of UTCPD.VBSCALE register field. It supports:
- "divide-20": External VBUS voltage divider circuit should be 1/20
for EPR application. The divided voltage compares with
200mV to set or clean VBUS Present bit.
- "divide-10": External VBUS voltage divider circuit should be 1/10
for SPR application. The divided voltage compares with
400mV to set or clean VBUS Present bit.
Signed-off-by: Chun-Chieh Li <ccli8@nuvoton.com>
Nordic SoCs implement an event system, for which the system can
optimize for low latency/high power or low power.
Add soc level implementation of reference counted API which will
optimize for low latency if any part of the system requires it.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Add a driver for the MB85RSM1T FRAM chip.
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The HAL configuration binding can be done dynamically based on the
IP's address space. The `hal-cfg-index` property is more tied to
software rather than hardware so remove it as an attempt to clean
up the binding.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add USB node to apollo4p and apollo4p_blue qualifier, and apollo4p_evb
and apollo4p_blue_kxr_evb board to enableUSB support on the MCU and
its EVB.
Signed-off-by: Chew Zeh Yang <zeon.chew@ambiq.com>
These samples demonstrate how to use the bluetooth 6.0 channel
sounding APIs. A basic distance estimation algorithm is included.
Signed-off-by: Olivier Lesage <olivier.lesage@nordicsemi.no>
Before that fix the names for UDMA could be misleading.
With that fix the namespace is clear and easy to follow.
Same applies for peripheral addresses and pad config.
Signed-off-by: Sven Ginka <s.ginka@sensry.de>
Add npcm miscellaneous device control and power and clock control
instances.
Add device tree bindings for npcm power and clock control.
Signed-off-by: Alan Yang <tyang1@nuvoton.com>
Add npcm clock control driver.
Signed-off-by: James Chiang <cpchiang1@nuvoton.com>
Signed-off-by: Joseph Liu <kwliu@nuvoton.com>
Signed-off-by: Alan Yang <tyang1@nuvoton.com>
Add initial support of the mailbox driver based
on the inter VM shared memory mechanism similar
as the existing IPM driver.
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
Gives an example where the timeout value is 15seconds,
the prescaler of 8 can let the LPTIM count from 0 to 16 seconds
with LSE
Signed-off-by: Francois Ramu <francois.ramu@st.com>
With this change, the LPTIM counter will be able to set
its timeout to the st,timeout value. So that system can
sleep for that period without interruption.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Filters already only allow arm and native, so exclude everything else
very early and reduce churn and build time.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Filters already only allow arm and native, so exclude everything else
very early and reduce churn and build time.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Replace the enum for load modes for the iCE40 with a boolean flag,
as there are only two options:
- SPI: default, which should be used whenever possible
- GPIO bitbang: workarorund, in case a low-end microcontroller is used
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Flags added allow keeping a pin as input/output by not disabling
the output buffer when configuring it as an input and by not
disabling input enable when configuring it as output. This can
be useful to implement signal diagnosis or for testing purposes.
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
Added empty fp register structs for ARM combinations not handled,
i.e. any ARM without a fpu.
Signed-off-by: Lars-Ove Karlsson <lars-ove.karlsson@iar.com>
This commit adds the bt_hci_driver.close function for Ambiq
Apollo3x SoC. Also update the hal_ambiq revision including
the necessary support.
Signed-off-by: Aaron Ye <aye@ambiq.com>
If a gateway is not set for a interface,
also log the destination address.
Also print the interface index instead of the
interface pointer.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Log the address and the err/reason values in the connected
and disconnect callbacks.
Since these values are not part of the BTP events it is
difficult to follow the order and reason why disconnects
happen when debugging.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Increase the EXECUTION_TIMEOUT (real time timeout at which the test
will be killed), so we have more margin for CI.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Increase the EXECUTION_TIMEOUT (real time timeout at which the test
will be killed), so we have more margin for CI.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Increase the EXECUTION_TIMEOUT (real time timeout at which the test
will be killed), so we have more margin for CI.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The sample had a few off-by-ones in the code, which caused access
to invalid data.
Fixed by setting the right buffer sizes and the right AD length
fields.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
When CONFIG_LLEXT_STORAGE_WRITABLE is selected and .pre_located is
set, the BSS section is allocated by the user too, no need to
allocate it internally.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
posix.common contains testsuites that can be separated into smaller
groups of tests. This change moves rwlocks into a singular
testsuite at tests/posix/rwlocks app directory.
Signed-off-by: Marvin Ouma <pancakesdeath@protonmail.com>
posix.common contains testsuites that can be separated into smaller
groups of tests. This change moves semaphore into a singular
testsuite at tests/posix/semaphores app directory.
Signed-off-by: Marvin Ouma <pancakesdeath@protonmail.com>
RX FIFO flushing on RXTO event should only be performed when
UARTE peripheral might be disable during inactivity and that
happens when low power modes is enabled or when device runtime
PM is used. Flushing was incrementing flush_cnt which was not
used (flushed data is not copied to the next buffer) which
was causing data loss and invalid RX data length reporting.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Switch from using direct `strtol` calls to `shell_strtol`.
This change leverages the extensive error handling provided
by `shell_strtol`.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Since the `fb` pointer is always assigned to `char_fb`, there is no need
for a `NULL` check. Additionally, removed setting `fb->buf` to `NULL` in
`cfb_framebuffer_init` as it will be overwritten by subsequent operations.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Added `len` to store the result of `strlen(str)` to avoid
multiple calls to `strlen` in the `for-loop`.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
