Add display shield rtk7eka6m3b00001bu support
Signed-off-by: Danh Doan <danh.doan.ue@bp.renesas.com>
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Change pinctrl-0 dts prop as optional in case DSI display is used
Add these APIs support: set_brightness, set_contrast, get_framebuffer
Add a new config to select frame buffer section
Signed-off-by: Danh Doan <danh.doan.ue@bp.renesas.com>
Keep the err in code as it is convention in Bluetooth code, remove ret,
change error_code as avdtp_err_code for avdtp protocol error.
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
We drop the packet if TTL or hop limit is 0, but we should
also unref the packet in this case because we return 0 to
the caller which is not then able to free the packet because
it thinks that the packet was sent properly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
When two tach use simultaneously, I find that the both tach status will
be cleared at once, which causes one of tach not to get rpm speed.
So I change it to clear status only one tach at a time.
This issue is reported by Huaqin:
https://partnerissuetracker.corp.google.com/issues/404067663?pli=1
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
The test_send_ipv6_fragment_without_hbho() test did not set link layer
protocol type for the packet. It is needed in this case because we
are sending a ready made packet and the protocol type is unknown
otherwise.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The check_ip() in net_core.c did not check that the packet
Ethernet type is either IPv4 or IPv6. This meant that we for
example checked TTL also for ARP packets which is pointless as
those are not IPv4 packets.
Fix this by checking the link layer protocol type of the packet
to be either IPv4 or IPv6 before doing L3 checks.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This maps to Zephyr power state Standby. In this power
state the OS Timer cannot be used as a wakeup source as
it will be powered off. Hence the counter is enabled
and RTC is used to keep track of system ticks and wakeup
the system.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Since the clock source when running in PM mode 3 is the
slower 1KHx clock, we adjust the SYS_CLOCK_TICKS_PER_SEC
value to get better accuracy.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
This clock is used for certain peripherals such
as RTC.
On certain RW612 boards such as rd_rw612_bga, XTAL32K
and ENET share pins. Add code to check if ENET and
XTAL32 are enabled at the same time.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
nRF70 driver now uses a separate heap, so, no need to explicitly
configure the kernel heap.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
In the linker script generator there was one error checking
construct that used regexp and that ended up in the generated
linker file, which caused parsing problems with the IAR
linker. It was unnecessary. Also updated
common-rom-kernel-devices.ld.
Signed-off-by: Lars-Ove Karlsson <lars-ove.karlsson@iar.com>
Add support to work with the LCD-PAR-S035 display
that is connected over the PMOD interface.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Add support for the LCD-PAR display to communicate over
the SPI bus which is available on the PMOD connection interface.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
The TOOLCHAIN_DISABLE_WARNING/TOOLCHAIN_ENABLE_WARNING macros are easier
to read and compiler agnostic.
Signed-off-by: Tom Hughes <tomhughes@chromium.org>
The TOOLCHAIN_IGNORE_WSHADOW_BEGIN and TOOLCHAIN_IGNORE_WSHADOW_END
macros can be replaced with the more generic
TOOLCHAIN_DISABLE_WARNING(TOOLCHAIN_WARNING_SHADOW) and
TOOLCHAIN_ENABLE_WARNING(TOOLCHAIN_WARNING_SHADOW) macros.
Signed-off-by: Tom Hughes <tomhughes@chromium.org>
Recently 0ae0c3dc44 allowed for three digit priorities, this resulted
in objects potentially matching multiple sections, for example:
.z_init_PRE_KERNEL_2_0_0_
.z_init_PRE_KERNEL_2_?_*
.z_init_PRE_KERNEL_2_???_*
This does not seem to be detected by ld, but the IAR linker emits a
warning.
Add some extra qualifiers in the object section name to make it
unambiguous, this has the extra value of making it easier to interpret,
for example going from:
.z_init_POST_KERNEL_90_00012_
to
.z_init_POST_KERNEL_P_90_SUB_00012_
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix K_MEM_PARTITION_P_RX_U_RX definition to allow code execution from
userspace. Add K_MEM_PARTITION_P_RX_U_NA definition that allows code
execution only by kernel.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
