nrf54h20 device requires device runtime PM to be enabled when
device PM is in use.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Now that the clock switching is implemented and most hosts support 16MHz
SPI, increase the default to 16MHz.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
In order to support higher frequencies than 8MHz, we need to implement
frequency switching while waking up the RPU, as it has to be done only
at 8MHz, once RPU is awake, we can switch back to the configured (DTS)
frequency.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Configure and enable SDMMC2 for the STM32N6570-DK.
Also configure and enable the PLL2 and the IC4 to use them as a 48MHz
source clock for the SDMMC.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Implement support for scatter-gather DMA transfers in the siwx917 driver.
This enhancement allows the driver to handle multiple non-contiguous memory
buffers in a single DMA transaction
Signed-off-by: Sai Santhosh Malae <Santhosh.Malae@silabs.com>
Updated the driver to ensure that each DMA channel can properly
assign and handle individual callbacks.
Signed-off-by: Sai Santhosh Malae <Santhosh.Malae@silabs.com>
This new API allows the assignment of desired DMA channels for
peripheral transfers, enhancing flexibility and control over DMA
operations.
Signed-off-by: Sai Santhosh Malae <Santhosh.Malae@silabs.com>
Refactored the driver code to ensure compatibility with the
dma_context API, improving maintainability and consistency
with other DMA drivers in the Zephyr project.
Signed-off-by: Sai Santhosh Malae <Santhosh.Malae@silabs.com>
1. Corrected the burst length processing to be handled in bytes
for the siwx917 DMA drivers.
2. Removed overlay and configuration files associated with the
chan_blen_transfer test application. The chan_blen_transfer
test application attempted to use 8 and 16 byte bursts, which
are not supported by the siwx91x UDMA.
Signed-off-by: Sai Santhosh Malae <Santhosh.Malae@silabs.com>
Current code configures the higher bits ahead of drive strength
to be "1", this patch fix this issue.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Lei Xu <lei.xu@nxp.com>
Looping while waiting for auto-negotiation to complete can block the
system workqueue for several seconds.
Signed-off-by: Kevin ORourke <kevin.orourke@ferroamp.se>
We've previously restricted Blackbox test
runs to just one test file - test_output.py.
That was a mistake.
This commit makes the relevant workflow run
all of the blackbox test files again.
Signed-off-by: Lukasz Mrugala <lukaszx.mrugala@intel.com>
Implement `irq_is_pending` in terms of the `irq_rx_ready` and
`irq_tx_ready` function calls.
Using `intstatus` directly results in an implementation that does not
conform to the interrupt driven UART API. Since `intstatus` bits are
only only set when a buffer transitions from full to empty, any calls to
`irq_is_pending` before any bytes have been sent will return 0. This is
problematic since the documented implementation for the API IRQ handler
is:
```
while (uart_irq_update(dev) && uart_irq_is_pending(dev)) {
if (uart_irq_rx_ready(dev)) {
...
}
if (uart_irq_tx_ready(dev)) {
uart_fifo_fill(dev, ...);
}
}
```
If `uart_irq_is_pending` does not return 1 until the first byte is sent,
we never end up pushing data to be transmitted into the `uart_fifo_full`
function.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Add defines to avoid magic values in the dtsi.
Replace usb_dc_stm32_get_maximum_speed() with device tree property.
- Use DT_INST_STRING_UPPER_TOKEN(0, maximum_speed) to set the USB speed.
- Remove PCD_SPEED_FULL initialization.
Signed-off-by: Khaoula Bidani <khaoula.bidani-ext@st.com>
Add defines to avoid magic values in the dtsi.
Replace usb_dc_stm32_get_maximum_speed() with device tree property.
- Use DT_INST_STRING_UPPER_TOKEN(0, maximum_speed) to set the USB speed.
- Remove PCD_SPEED_FULL initialization.
Signed-off-by: Khaoula Bidani <khaoula.bidani-ext@st.com>
On STM32 USB, there are currently four types
of maximum-speed: "super-speed", "high-speed",
"full-speed" and "low-speed" (if present).
To simplify the driver, add maximum-speed if
not present as a dts property.
Signed-off-by: Khaoula Bidani <khaoula.bidani-ext@st.com>
Updated `CMakeLists.txt` and `Kconfig` to integrate power management
for RA8D1, RA8M1, and RA8T1.
Modified `Kconfig.defconfig` to configure ULPT timer as the system timer
when power management is enabled:
- Adjusted `SYS_CLOCK_HW_CYCLES_PER_SEC` and `SYS_CLOCK_TICKS_PER_SEC`
for ULPT timer.
- Disabled `CORTEX_M_SYSTICK` when ULPT timer is used as the system timer.
Implemented power management logic in the new `power.c` file for:
- RA8D1 (`soc/renesas/ra/ra8d1/power.c`)
- RA8M1 (`soc/renesas/ra/ra8m1/power.c`)
- RA8T1 (`soc/renesas/ra/ra8t1/power.c`)
Signed-off-by: Khanh Nguyen <khanh.nguyen.wz@bp.renesas.com>
ULPT nodes:
- Added `ulpt0` at 0x40220000 (channel 0).
- Added `ulpt1` at 0x40220100 (channel 1).
- Included timer sub-nodes with `renesas,ra-ulpt-timer` compatibility.
Power state nodes:
- `stop0`: Runtime idle state mapped to LPM sleep mode.
- `stop1`: Standby state mapped to LPM software standby mode.
Signed-off-by: Khanh Nguyen <khanh.nguyen.wz@bp.renesas.com>
#84065 replaced diagnostic pragmas with TOOLCHAIN_* macros, but we don't
need to use that here since __used is a cleaner way to indicate that the
function is used and will also prevent it from being optimized away at
link time if LTO is enabled.
Signed-off-by: Tom Hughes <tomhughes@chromium.org>
If the AG works as Data Channel Acceptor, the ACL conn cannot be known
by the application of AG. Similar with HF, add ACL conn as the first
parameter to the `connected` callback of AG.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Add `BOTH_SUPT_FEAT(ag, _hf_feature, _ag_feature)` to check if the
feature is supported by both side.
Add `HF_SUPT_FEAT(ag, _feature)` to check if the feature is supported
by HF.
Add `AG_SUPT_FEAT(ag, _feature)` to check if the feature is supported
by AG.
Use `BOTH_SUPT_FEAT/HF_SUPT_FEAT/AG_SUPT_FEAT` to optimize code that
checks whether a feature is supported.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
The lock/unlock for AG/HF feature read access is unnecessary.
For AG feature, it only be changed when creating new AG object.
For HF feature, it only be changed when exchanging feature in SLC
establishment.
Remove the hfp_ag_lock/hfp_ag_unlock for AG/HF feature read access.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
There is an error reported in platform `native_sim` that the value of
`EOPNOTSUPP` is same as `ENOTSUP`.
It cause the building error `duplicate case value '-95'` reported.
Use `ENOEXEC` to replace `EOPNOTSUPP` to fix the building issue.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Divide hfp_internal.h into two parts, HFP HF part hfp_hf_internal.h and
HFP common part hfp_internal.h.
Includes "hfp_internal.h" in file "hfp_ag_internal.h".
Includes "hfp_ag_internal.h" in file "hfp_ag.c".
Includes "hfp_internal.h" in file "hfp_hf_internal.h".
Includes "hfp_hf_internal.h" in file "hfp_hf.c".
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Add a option `HFPHF` to find HFP HF SDP records from HFP AG side.
Add a SDP records discovery parameter `discov_hfphf` for this option.
Add a function `sdp_hfp_hf_user` to handle the discovery result.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Define SDP records for HFP AG. Register HFP AG SDP service records in
AG initialization.
Register HFP AG RFCOMM server in AG initialization.
Register HFP AG SCO server in AG initialization.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Add function `bt_hfp_hf_connect` to initialize the Service Level
Connection establishment procedure.
Add function `bt_hfp_hf_disconnect` to release the Service Level
Connection.
Clear HF object if the RFCOMM is disconnected.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Add configuration `CONFIG_BT_HFP_AG_HF_INDICATORS` to enable feature
HF Indicators.
Add configuration `CONFIG_BT_HFP_AG_HF_INDICATOR_ENH_SAFETY` to
support HF indicator `Enhanced Safety`.
Add configuration `CONFIG_BT_HFP_AG_HF_INDICATOR_BATTERY` to support
HF indicator `Remaining level of Battery`.
Add function `bt_hfp_ag_hf_indicator` to activate/deactivate HF
indicator.
Optimize the handle of AT command `AT+BIND`.
Handle AT command `AT+BIEV`.
Add callback `hf_indicator_value` to notify the value of HF indicator.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
