This PR set the correct value for the stm32F7 devices.
And change vrefint-cal-addr to <0x1FF07A2A> for stm32F722-F723
soc serie.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The Adafruit Grand Central M4 Express is an ARM development board
with the form factor of an Arduino Mega.
It features 70 GPIO pins, a microSDHC slot and 8MiB of QSPI Flash.
Signed-off-by: Lukas Jung <lukas.jung@mailbox.org>
Added support column for all features of m5stack_core2 board.
Link to m5stack_core2_ext added.
Signed-off-by: Martin Kiepfer <mrmarteng@teleschirm.org>
* SD card support via sdhc-spi driver added. SPI speed is
configured to 20MHz for stability reasons. Some cards
seem to not working properly with 25HMz or even higher speeds.
* Pinmux ctrl for SPI3 pins reworked. Native cs removed
as gpio chip-selects are required.
Signed-off-by: Martin Kiepfer <mrmarteng@teleschirm.org>
Adapts the `pb_remote_timeout` test to the updated `bt_mesh_suspend`
API.
Suspension is scheduled with a small delay to allow publications to be
sent before suspending Mesh.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
Adds two test-cases; one for suspending and resuming Mesh,
and one for suspending Mesh and disabling Bluetooth before
re-enabling Bluetooth and resuming Mesh.
Both tests checks that periodic publication is stopped during
suspension.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
Disables Mesh advertising when suspending, and enables advertising
when resuming Mesh.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
Adds a disable function for the extended advertising which stops and
deletes the advertising instances, allowing them to be properly
reinitialized when calling `bt_mesh_adv_enable()` after bluetooth has
been disabled and re-enabled.
For the legacy advertising, the function terminates the advertising
thread. If legacy advertising is used, `bt_mesh_adv_init()` must be
called before `bt_mesh_adv_enable()` to properly resume advertising
after suspension.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
This commit reworks the adltc2990_fetch_property_value function
to pass its result through a variable pointer instead of direct return.
This is done in part to separate the errno value being return in the
default case of the switch from the result of the function, but also
to make it easier the fix a Coverity issue regarding the unhandled
return values of i2c reads.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
This commit adds a missing return value check. Since the I2C write
failed we release the semaphore and returning immediatly instead of
using goto exit.
Fixes#65352
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
This commit adds a missing return value check for a register read.
The affected function was updated to use the regular errno return value
and to pass the result through a pointer instead.
Fixes#65346
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
This commit adds a missing return value check during register read.
Added an imidiate return to remove the seemingly unwanted side
effect of also waiting for the bus read to work.
Fixes#65374
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
This commit adds a missing return value check during register read.
Added an imidiate return to remove the seemingly unwanted side
effect of also waiting for the bus read to work.
Fixes#65383
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
Remove disable of QSPI for BL5340 DVK cpuapp NS build.
The QSPI is not configured as a secure peripheral in the generic
nrf5340 platform support.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Switch BOARD_BL5340_DVK_CPUAPP_NS TF-M board selection from using the
platform support that is built-in to TF-M module, and instead use
the generic nRF5340 cpuapp platform support that all other nrf5340 SoC
related boards use.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add pin-control configurations for UART1 pin assignments.
The GPIO pins matches the ones used in Laird Connectivity TF-M boards
RTE_Device.h file.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
- Removed preset initializations. Done in auto-pts client.
- Added one additional preset in overlay-le-audio.conf.
Signed-off-by: Henrik Eriksen <heri@demant.com>
This was somehow missed, but since ICMP rework, message handlers should
not dereference the packet, as it's done by the ICMP lib.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Commit 55802e5e86 fixed error handling of
TX errors, in case ARP request was generated. There are however also
other places where post-ARP cleanup should be done on the TX path (like
running out of buffers for Ethernet L2 header allocation).
This commit fixes those cases in ethernet_send(), where function would
exit early and report error after ARP prepare stage.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Simplify the driver header implementation, so that there are not
structs and unions different per each situtaion, and make just one
function for the enet module drivers to call on each other. Also,
capitalize existing enums.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Long arguments are handy for new users. Also use hyphen's rather than
underscore to follow the convention.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Newly added security types are missing from the help. Also, now that we
have two variants of PSK, use the prefix to disambiguate.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Python's sets are not deterministic.
`devices` were already sorted but `dev_supports` is still a
non-deterministic set. Sort dev_supports to make the graph output
deterministic.
Fixes commit 29942475c5 ("scripts: gen_handles: output dependency graph")
It is quite ironic that this initial and non-deterministic graph commit
was concurrent with and slightly delayed other commit
f896fc2306 ("scripts: gen_handles: Sort the device handles") which
fixed another, similar non-determinism issue in the same area. A true
"whack-a-mole"!
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
This allows sorting objects consistently without having to specific a
key.
No functional change yet.
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Set the chosen 802154 radio in DT for the
nrf5340bsim_nrf5340_cpuapp so we can build with the
radio driver built into the net core.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
* Update the HW models module to
9b985ea6bc237b6ae06f48eb228f2ac7f6e3b96b
Including the following:
* 9b985ea nrf_ccm: Add RATEOVERRIDE subscribe support
* 8592230 nrf_hack: Add comments
* 5775f4c docs: Very minor typo and grammar fixes
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
When interface names are enabled, a default name is applied
after initialization. Unintuitively, this overwrites any name that is
set during the net_if init.
This change sets a default name first, and then allows net_if
init to overwrite that default name if it chooses to.
Signed-off-by: Noah Luskey <noah@silvertree.io>
Signed-off-by: Noah Luskey <LuskeyNoah@gmail.com>
Make sure that events flagged as high priority are handled when
CONFIG_BT_RECV_BLOCKING is not defined.
Fix for #65892.
Signed-off-by: Michele Sardo <msmttchr@gmail.com>
A warning is printed in start of the test about this.
Increase CONFIG_NET_IF_MAX_IPV6_COUNT=2 and
CONFIG_NET_IF_MAX_IPV4_COUNT=2 so that the tests pass
in frdm_k64f and some other boards.
Fixes#66020
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
native_sim is superceeding native_posix.
Let's recommend users to use it instead.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add support for testing the `dma_emul` driver which simply uses
software emulation (i.e. asynchronous memcpy in a workqueue) for
performing DMA operations.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
Like other driver APIs, we can add an `emul` variant to
`native_posix` and `native_posix_64` that should allow us to
simplify applilcation and library development and to also
increase test coverage in CI.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
Add an emulated DMA driver. Emulation drivers are great to have
for each driver API for multiple reasons:
- providing an ideal / model driver for reference
- potential for configurable backend support
- seamless integration with device tree
- multi-instance, etc, for all supported boards
- fast regression testing of app and library code
Since many other drivers and lbraries depend on DMA, this might
help us to increase test coverage.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
Many driver APIs are opting to provide an `emul` driver
implementation that can be used for a number of purposes.
- providing an ideal / model driver for reference
- configurable backends
- seamless integration with device tree
- support for native posix, qemu, and any other board
- fast regression testing of app and library code
Provide an initial set of bindings for `zephyr,dma-emul` devices.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
