Replaced tcp_out() with tcp_out_ext() when sending
SYN during tcp connect, so we can intercept error value,
beacuse in such case the packet would not be sent at all
and the stack would not trigger any mechanism to flush
this context so it ends up leaking. These scenarios can
arise when the underlaying interface is not properly
configured or is disconnected. The conn is marked to be
closed and is closed before exiting tcp_in().
Since we can now identify this case we can also exit
early in the net_tcp_connect() function and not wait
for any timeout.
Signed-off-by: Daniel Nejezchleb <dnejezchleb@hwg.cz>
This commit updates migration-guide and release-notes docs with
the changes introduces by PR 71827 and PR 72243.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Found via static analysis. Two separate error paths where failing to
check the return code leads to undefined behavior:
1. In `litex_clk_get_phase`, the divider stays set to 0 when
`litex_clk_get_clkout_divider` errors out, which leads to a division
by 0.
2. In `litex_clk_calc_duty_normal`, the `duty` struct is used
uninitialized if `litex_clk_get_duty_cycle` errors out.
In both case, checking the return code and returning early resolves the
issue.
Signed-off-by: François Baldassari <francois@memfault.com>
Use BLE.ADDR to create unique (to some extent) EUI64
on nRF54H20 in some cases inside the IEEE 802.15.4 driver.
The amount of EUI64-s available in such a way is very limited
(~16 million).
However, currently there does not seem to be another feasible way to
get device identifiers on nRF54H20 (such are kept in SICR, to which the
radio core has no access).
Signed-off-by: Piotr Koziar <piotr.koziar@nordicsemi.no>
Adds an appropriate condition to the Kconfig as
the temperature driver is not supported for nRF54H20 devices yet.
Without this change, a build with NRF 802.15.4 libraries produces
Kconfig error.
Signed-off-by: Piotr Koziar <piotr.koziar@nordicsemi.no>
This commit fixes the issue where a serialization
error was reported after properly sending a data with 'icbmsg' backend.
The icbmsg send function's return code is set to
the sent data's len as in other backends.
The related docs were fixed and updated.
Signed-off-by: Piotr Koziar <piotr.koziar@nordicsemi.no>
Clock_control is currently not supported on nRF54H20.
This commit adds new way of handling the hfclk targeted for nRF54H20.
This solution shall be replaced once the clock_control is supported
for nRF54H20.
Signed-off-by: Piotr Koziar <piotr.koziar@nordicsemi.no>
Adds channel 15 to the pool of grtc channels available
for allocation (i.e. with 'z_nrf_grtc_timer_chan_alloc')
on nRF54H20.
The change is motivated by lack of available channels
for the nrf_802154_timestamper when building for nRF54H20.
Signed-off-by: Piotr Koziar <piotr.koziar@nordicsemi.no>
Move STM32_MEMMAP outside of SOC_FLASH_STM32.
That allows memory-mapped application to
be built without internal flash controller.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
This commit should deal with adding a missing
direction case as memory-to-peripheral
and peripheral-to-memory transfers
should be considered the same.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
This commit should address the #73803 issue
where the DMA node does not provide support
for the #dma-cells binding. Peripherals should
specify one or more DMA channels via the dmas
and optionally dma-names DT properties.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
Our documentation uses image formats such as WebP that are not supported
by LaTeX. This commit enables Sphinx's sphinx.ext.imageconverter
extension, and updates the documentation to indicate ImageMagick is
required to build docs.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Update the status to maintained, add a maintainer and collaborators, and
also update the label to match the recent spelling change ("SiLabs" ->
"Silabs").
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Add Johan, Jérôme and Aksel to Silabs Platforms. Also update the subsystem
and GitHub label name from "SiLabs" to "Silabs", since this is the more
usual spelling.
Signed-off-by: Aksel Mellbye <aksel.mellbye@silabs.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
In new hardware model, the arch subfolder is no more: updating cmake config
documentation to reflect this change
Signed-off-by: Eve Redero <eve.redero@gmail.com>
Add descriptions for recently introduced IPv4 and IPv6
connectivity events to the net event monitor.
Signed-off-by: Georges Oates_Larsen <georges.larsen@nordicsemi.no>
Modify the test cycle routines to verify recently added IPv4- and
IPv6-specific events.
Signed-off-by: Georges Oates_Larsen <georges.larsen@nordicsemi.no>
conn_mgr now fires:
- NET_EVENT_L4_IPV4_CONNECTED
- NET_EVENT_L4_IPV4_DISCONNECTED
- NET_EVENT_L4_IPV6_CONNECTED
- NET_EVENT_L4_IPV6_DISCONNECTED
These events track whether there are any ready ifaces offering
specifically IPv4 or specifically IPv6 connectivity.
Signed-off-by: Georges Oates_Larsen <georges.larsen@nordicsemi.no>
Don't track up/down blame separately.
Instead, track a single last-blame iface.
Don't track blame iface inside set_ready.
Instead, track directly inside handle_update.
These two changes will simplify the addition
of blame for IPv4- and IPv6-specific events.
Signed-off-by: Georges Oates_Larsen <georges.larsen@nordicsemi.no>
Instead of incrementing and decrementing global counter,
just recompute the ready-count from scratch every time
conn_mgr_mon_handle_update is called.
This will simplify the introduction of additional ready count types.
This should have no externally observable impact on the behavior of
conn_mgr.
Signed-off-by: Georges Oates_Larsen <georges.larsen@nordicsemi.no>
In case of ACD Probe/Announcement, all we need is to generate ARP
packet, we don't really want any cache entries to be created or searched
for. There was a bug, that a cache entry was created for the
Announcement sent, resulting in skipped ARP packet generation and
malformed packet being sent by the ACD module.
Therefore, simplify all this, by simply returning early in case of
conflict detection packets.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The autoconf module can now reuse generic address conflict detection,
which was added for all address types.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In case a conflict was detected on a DHCP-assigned address, send a
Decline message to the server and start over.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In case IPv4 conflict detection is enabled, monitor network events to
determine whether IPv4 address is ready to use or not, so that the
library returns only after the network setup is fully complete.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Connection manager needs to monitor ACD events as well to determine
whether a preferred IPv4 address is available.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add support for IPv4 conflict detection, as specified in RFC 5227.
The new feature is optional and disabled by default.
Address conflict detection was implemented as a part of the IPv4
autoconf feature can be generalized to be available for all address
types.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
When the CONFIG_BOOT_BANNER flag is set to "n", but CONFIG_BOOT_DELAY
is enabled, there is a delay message printed at boot time.
This allows for the whole boot banner to be disabled.
Signed-off-by: Krzysztof Sychla <ksychla@antmicro.com>
The VDED was adding the channel information per clone. But it could be
done in the original buffer. This commit fixes that by adding the
channel information to the original buffer and not for each clone. As a
result, we have a more straightforward VDED execution with fewer copies.
Signed-off-by: Rodrigo Peixoto <rodrigopex@gmail.com>
Move the audio related files to a new subdirectory called
audio.
The purpose of this is to clean up the file structure a bit,
and also allow for better filtering of the files.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
When low power mode is enabled then whenever UARTE is not active,
driver attempts to put the peripheral into the lowest power state
by stopping and disabling UARTE. However, it did not put pins into
sleep state which could lead to increased current consumption.
Adding pins state handling to the low power mode.
Pins are put into sleep state only if CONFIG_PM_DEVICE=y.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
In function pcal64xxa_process_input, lock was not released in case of
error when calling inputs_read.
This was causing an infinite wait in the following calls of functions
using I2C bus.
Signed-off-by: Vincent Geneves <vgeneves@kalray.eu>
Add a symbol to enable device power state constraints this
saves resources when this feature is not needed.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Test that device pm state constraints work as expected.
It declares a device in DT that specify that two pm states cause
power loss and use this information when the device is in the middle
of an action.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Declare power state constraints for a device in devicetree.
It allows a map between device instances and power states that disable
their power. This information is used by a new API
(pm_policy_device_power_lock_put/get) that automically set/release
pm state constraints.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Removed an unnecessary cast to void * from a function that already
had the correct signature.
This makes for more portable code as casting between code and data
pointers are frowned upon by the C standard.
Signed-off-by: Lars-Ove Karlsson <lars-ove.karlsson@iar.com>
Remove pre hardware model v2 overlays present for RT11xx boards, that
were missed in the HWMv2 migration
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
In commit a30c5731ae (tests: drivers: can: api:
support numaker_m2l31ki, 2024-05-31), CONFIG_USERSPACE was disabled for
the numaker_m2l31ki. This fix is valid to support running the CAN API
testsuite, but Zephyr's infrastructure does not properly support
disabling userspace at the board level.
As a temporary workaround, reenable userspace to fix failing CI tests
on this board.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Replace the leftover `&&` operator with UTIL_AND(), so that this DT API
can be evaluated at C preprocessor time.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Abstract slab pointer validation and apply it to block dequeue during
allocation in addition to the existing block freeing. This should help
catching some buffer overflow induced corruptions.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
As it is, blocks are allocated going backward within the buffer.
There is nothing fundamentally wrong with that, but it makes debugging
unnatural with the successively descending addresses. Create the free
list so pointers are oriented forward, at least initially.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
This macro allows to know the size of a struct member at compile time.
Several parts of the Zephyr code are currently using directly the macro
code.
Also added a unit test.
Signed-off-by: Adrien Ricciardi <aricciardi@baylibre.com>
