Reduce duplication in STM32 dietemp bindings by regrouping the 'ntc'
property declared in both "st,stm32-temp" and "st,stm32c0-temp-cal"
to the shared "st,stm32-temp-common" binding.
"st,stm32-temp-cal" is also modified to block 'ntc' property on include as
no dual-calibration sensors to date require it (this could be changed later
when need arises).
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Update all the conversion code in the STM32 dietemp sensor driver to be
more readable and match the Reference Manuals. Additionally, comment all
the code to make it easy to understand.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Move the reading of calibration data from manufacturing flash to a
dedicated function. This makes introduction of new STM32 series easier.
Additionally, use the sys_read16 primitive to read data instead of
manipulating and dereferencing raw manufacturing flash pointers.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Rename the fields of the STM32 dietemp sensor driver data structure to
match the names in Reference Manual more closely, and add documentation
comments to all of them.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Factor out the ADC-sample-to-temperature conversion logic from the sensor
subsystem API implementation, and move it to a dedicated function.
This makes the driver more readable.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Moves the temperature sensor channel enable and selection to separate
functions. This improves the driver's readability and makes introduction
of new STM32 series easier.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Set the 'avgslope' property of 'st,stm32c0-temp-cal' to required, and
remove its default value, to ensure new series cannot be introduced without
setting the property to the correct value explicitly.
This change does not require any DTSI modification, because there are only
two files using this compatible (stm32f030.dtsi / stm32c0.dtsi), and both
of these already set 'avgslope' explicitly.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Set the 'avgslope' property of 'st,stm32-temp' to required, and remove its
default value, to ensure new series cannot be introduced without setting
the property to the correct value explicitly.
This change does not require any DTSI modification, because there are only
two files using this compatible (stm32f1.dtsi / stm32f2.dtsi), and both of
these already set 'avgslope' explicitly.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Set the 'v25' property of 'st,stm32-temp' to required, and remove its
default value, to ensure new series cannot be introduced without setting
the property to the correct value explicitly.
This change does not require any DTSI modification, because there are only
two files using this compatible (stm32f1.dtsi / stm32f2.dtsi), and both of
these already set 'v25' explicitly.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
The typical value for V25 is different on the STM32F100 line compared
to other STM32F1 MCUs. Update the DTS property to the correct value.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Add the missing 'avgslope' property to the DTSI for STM32F030/STM32F070.
This fixes improper results being returned by the driver: the correct
value for the average slope is 4.3mV/°C (4300 µV/°C), but the binding's
default value of 2.53mV/°C was used instead, since property was missing.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Remove the "Negative Temperature Coefficient" attribute from the STM32F2
die temperature sensor node, as it does not correspond to the hardware.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Once panic mode is entered, the log write functions are called from an ISR,
so must not try to acquire locks.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Add more parameter checking for the unittests for the
CAP procedure 'broadcast reception stop'
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
This is in preparation for adding another SoC where qemu_xtensa
is no longer valid choice. So use qemu_xtensa/dc233c as it is
the same as the old qemu_xtensa.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Update nrfx drivers with the minimum number of bytes that can be sent
in a single call to `uart_fifo_fill`.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Update the interrupt driver UART drivers that use `struct ring_buf`
internally to report the number of bytes that can be pushed in
`uart_fifo_fill` without fragmentation.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Update the documented value range that `uart_irq_tx_ready` returns in
order to provide more information to the callers about the number of
bytes that could be writted with `uart_fifo_fill` without fragmentation.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Fixes issue #78815
Specifies explicitly the location of the generated .config file
relative to the build directory.
Signed-off-by: Arrel Neumiller <rlneumiller@gmail.com>
Moves all Renesas sensor drivers into a vendor specific subdirectory
matching the organization used for other drivers.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
The argument of INPUT_SBUS_INIT is named `n,` but there are some places
where it references `id.` Correcting these.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
For the parts of the simulator which are dedicated for the native
platforms (POSIX arch based):
* Refactor the parts that interacts with the host, so it is possible to
use it also with embedded libCs
* Enhance it with more options to allow:
* Keeping the content just in RAM
* Erasing the EEPROM file at exit
* Clearing the file at boot
* Also show in the command line help the default file name.
As part of this:
* Update the kconfig dependencies, so we allow building it with other
C libraries in the native targets
* Update the table in the native_sim docs to indicate all C libraries
are supproted now
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Restore the s0 we saved early in ISR entry so it shows up
properly in the CSF.
Signed-off-by: David Reiss <dreiss@meta.com>
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
This is a bug fix for adxl372_get_status function.
This function is used to get STATUS1, STATUS2, FIFO_ENTRIES2
and FIFO_ENTRIES1 registers (they are continuously present
in the memory in this order). User can choose if it wants
STATUS2 and/or FIFO registers by passing pointers where
to store received values. Bug was when user doesn't want
STATUS2 and want FIFO regs. In that case calculated length
would be 3 which will result in reading of STATUS1, STATUS2
and FIFO_ENTRIES2 regs and not expected STATUS1, FIFO_ENTRIES2
and FIFO_ENTRIES1.
Signed-off-by: Vladislav Pejic <vladislav.pejic@orioninc.com>
Upgrade to accel_polling sample application to support
RTIO streaming functionality. This mode is enabled when
CONFIG_SENSOR_ASYNC_API is defined. NUM_SENSORS must be
set to the correct number of sensors used.
Signed-off-by: Vladislav Pejic <vladislav.pejic@orioninc.com>
The RT1170 MIPI DPHY requires a faster clock frequency setting for
the MIPI DPHY, or the pixel packet counts for the HFP, HBP, and HSA will
be incorrect, and the DSI transfers will stall. Raise the target DPHY
clock frequency to resolve this.
Fixes#78299
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit updates the FLASHRXBUF parsing functionality of eSPI TAF.
It ensures that data can be read correctly from FLASHRXBUF[0].
And, the eSPI TAF request can be parsed correctly.
Signed-off-by: Tom Chang <CHChang19@nuvoton.com>
This test works both with native_posix and native_sim.
native_sim will eventually not set NATIVE_SIM_NATIVE_POSIX_COMPAT
(i.e. not pretend to be native_posix) so let's correct this ifdef
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This driver works both with native_posix and native_sim.
native_sim will eventually not set NATIVE_SIM_NATIVE_POSIX_COMPAT
(i.e. not pretend to be native_posix) so let's correct the
dependencies.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Move the `Z_THREAD_LOCAL` macro from
`include/zephyr/toolchain/common.h` to `include/zephyr/types.h`.
This is needed since some `syscall.h` files are using TLS but aren't
including `zephyr/toolchain.h` (but they are including
`zephyr/types.h`).
Signed-off-by: Daniel Flodin <daniel.flodin@iar.com>
Current clocks configuration for the platform makes it impossible
to pass the IDLE_EVENT_STATS_PRECISION check. This is to be addressed
in the future.
Signed-off-by: Mateusz Hołenko <mholenko@antmicro.com>
