The driver has some non trivial macro setup, add another two test cases
so those gets build tested as well.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add a poll and scan mode for the driver. If any of these are set, the
driver does not use the GPIO interrupts to detect when the matrix has to
switch to polling mode. Instead, it keeps polling it all the time,
either by enabling all the columns and poll the rows for activity, or
just keep scanning all the time.
Poll mode is useful if the specific SoC used does not support GPIO
interrupt on all the row GPIOs at the same time, scan mode if it does
not even support selecting all the columns at the same time.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Tweak the polling mode so that the driver never exit polling mode if
poll_timeout_ms is 0. This is useful if the specific driver does not
support idle mode.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The state variable to tracking the unstable state of a key is currently
being cleared based on the bit value, which means that on release it's
not being cleared at all. Fix that by clearing using the bit mask
instead.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
scan_clk_cycle is used to store values from k_cycle_get_32(), it very
much needs to be a uint32_t.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Implements sync established and sync lost BTP events.
This was affecting GAP/PADV/PASE/BV-01-C test case.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
This allows for more tuning regarding Periodic Advertising Sync
behavior.
Required by GAP/PADV/PASE/BV-01-C qualification test case.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Add information about the IPv4 multicast IP_ADD_MEMBERSHIP and
IP_DROP_MEMBERSHIP socket options.
Add information about the IPv6 multicast IPV6_ADD_MEMBERSHIP and
IPV6_DROP_MEMBERSHIP socket options.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Zephyr has its own multicast join/leave API but for
interoperability, it is possible to use the multicast
socket API and IPV6_ADD_MEMBERSHIP and IPV6_DROP_MEMBERSHIP
socket options.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Zephyr has its own multicast join/leave API but for
interoperability, it is possible to use the multicast
socket API and IP_ADD_MEMBERSHIP and IP_DROP_MEMBERSHIP
socket options.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Commit 40c2e08e82 ("xcc/cmake: don't discard stderr; don't (ever!) use
ERROR_QUIET") fixed xcc but the corresponding code is duplicated. Fix
the duplicates too.
See that commit for the issue description, longer commit message and
rationale.
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
The current code triggers a false positive from the heuristic "Macro
compares unsigned to 0". It's triggered because of a use of `IN_RANGE`
that checks against the extremal values of a enum type.
This patch replaces the use of `IN_RANGE` with an explicit list of the
possible values of the enum.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/65575
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
This commit introduces a new interrupt controller driver used
for NXP's IRQ_STEER IP.
Apart from introducing the driver itself, this commit contains
the following changes:
1) Switch i.MX8MP to using the XTENSA core interrupt
controller instead of the dummy irqsteer one.
* this is required because the binding for the
irqsteer driver is no longer a dummy one
(since it's being used by the irqsteer driver).
As such, to avoid having problems, switch to
using another dummy binding.
2) Modify the irqsteer dummy binding such that it
serves the IRQ_STEER driver's needs.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
The command response buffer will return the total number of bytes
transfered. This will write back to the pointer which is to contain
the number of bytes sent or received.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
With I3C, when a controller does a read whether, through a private transfer
or a CCC, the target is responsible for issuing the End of Data through the
T bit, but the way the API is currently implemented, there is no way to
communicate this back up. For example, if a controller tries to read 100
Bytes (where the controller is to do an abort after 100 (or 101 bytes))
from a Target and the Target gives the EoD at the 42nd Byte, then there is
no way to currently know where the EoD occurred and how far it can be read
up to in the provided buffers.
This implements a num_xfer for `i3c_msg` and `i3c_ccc_payload` which the
driver is responsible for writing the total number of bytes transferred.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Add a testsuite to demonstrate proper functionality of blocking
in the log processing thread.
This serves to demonstrate the previous bugfix, to provide
missing test coverage for the option, and also to document what
pitfalls to avoid when blocking in the log processing thread.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
Add information about IPv4 TTL and IPv6 hoplimit changes
for unicast and multicast packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add information about IPv4 TTL and IPv6 hoplimit changes
for unicast and multicast packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
We are creating a multicast address in mDNS or LLMNR
responder so set the TTL or hoplimit using the multicast
variant API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
We specifically set TTL/hoplimit to 1 for LLMNR,
but only want to set it if in that specific case.
We must not pass TTL/hoplimit value 0 as that would
cause the packet to be dropped.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Make sure that statistics is properly update for dropped
packets when IPv4 TTL is 0 or IPv6 hop limit is 0.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
* Check IPv4 TTL or IPv6 hop limit and drop the packet if
the value is 0
* Check the IP addresses so that we do the loopback check
at runtime if the packet is destined to loopback interface.
* Update the statistics properly for dropped packets.
* Do not update sent packets if we drop packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The IPv4 TTL could only manipulated via net_context interface.
It makes sense to allow the same from socket interface via
the setsockopt/getsockopt calls.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The net_if_ipv6_set_hop_limit() API was missing the "_if_"
part in it. Fix this so that the network interface API is
consistent. The old function is deprecated and should not
be used. The old function is left to the code and it calls
the new properly named function.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This PR set the correct value for the stm32F7 devices.
And change vrefint-cal-addr to <0x1FF07A2A> for stm32F722-F723
soc serie.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The Adafruit Grand Central M4 Express is an ARM development board
with the form factor of an Arduino Mega.
It features 70 GPIO pins, a microSDHC slot and 8MiB of QSPI Flash.
Signed-off-by: Lukas Jung <lukas.jung@mailbox.org>
Added support column for all features of m5stack_core2 board.
Link to m5stack_core2_ext added.
Signed-off-by: Martin Kiepfer <mrmarteng@teleschirm.org>
* SD card support via sdhc-spi driver added. SPI speed is
configured to 20MHz for stability reasons. Some cards
seem to not working properly with 25HMz or even higher speeds.
* Pinmux ctrl for SPI3 pins reworked. Native cs removed
as gpio chip-selects are required.
Signed-off-by: Martin Kiepfer <mrmarteng@teleschirm.org>
