The TPIU supports serializing the data stream both using an UART-like NRZ
protocol as well as using Manchester encoding. Using Manchester encoding
has the advantage that it enables receivers that support it to recover the
clock from the SWO signal itself. This is particularly useful in situations
where the clock rate changes dynamically or is unknown (for example when
debugging the clock tree setup or working with a device with a misbehaving
main oscillator).
Add a Kconfig choice to switch the protocol, keeping the current default of
using the NRZ encoding.
Signed-off-by: Florian Larysch <larysch@fixme.gmbh>
The modem pipe APIs include synchronous calls to open/close,
which internally use a fixed timeout of 10 seconds. The timeout
should be configurable through the APIs, anywhere from K_NO_WAIT
to K_FOREVER.
This commit adds timeout parameters to the open/close APIs, and
updates in-tree usage of the open/close APIs to explicitly
provide the previously implicit timeout of 10 seconds.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
Added i2c configuration to test target_eeprom case for frdm_ke17z
Added `sample.drivers.i2c.target.kinetis` in sample.yaml for frdm_ke17z
and frdm_ke17z512 automatically run the tests
Signed-off-by: Anke Xiao <anke.xiao@nxp.com>
Add the following AD types:
- `BT_DATA_DEVICE_CLASS`
- `BT_DATA_SIMPLE_PAIRING_HASH_C192`
- `BT_DATA_SIMPLE_PAIRING_RAND_C192`
- `BT_DATA_DEVICE_ID`
- `BT_DATA_PAWR_TIMING_INFO`
- `BT_DATA_ESL`
Note that `BT_DATA_DEVICE_ID` has the same value as
`BT_DATA_SM_TK_VALUE` (0x10), this is not a mistake from the author but
a mistake in the Core Specification, specifically the Assigned Numbers
document with the version date 2024-04-10.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
There is problem with running this test in validation,
because of DBGR mode watchdog can't reset board by itself,
and it needs cold reset. This proves that test is not automated,
and should be exluded on this board.
Signed-off-by: Patryk Kuniecki <patryk.kuniecki@intel.com>
Updates the output sample to more closely resemble the output for a
recent Zephyr version (current was v1.14). Fixes#76275.
Updates broken tf-m documentation link to their new URL.
Signed-off-by: Adrien Leravat <adrien.leravat@gmail.com>
When dynamic fifo sizing is enabled the driver can assign fifo size
lower or equal to the reset value. Software must respect the maximum
sizes because fifo width registers are optimized during synthesis and
the larger values simply get discarded.
Use 16-bit values for FIFO depths because maximum FIFO depth the vendor
can configure the DWC2 otg is 32768.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
This creates a common folder in order to share code between similar
boards. This is mostly for the CC1352P1 and CC1352P7 launchpad which
are very similar but it could be probably useful for some other boards.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Add an API function allowing the application to determine the amount of
free bytes in the current sector.
Add a second API function allowing the application to switch to the next
NVS sector, calling the garbage collector on such sector.
The goal is togive more granularity to the application to control when
the garbage collector is triggered.
Signed-off-by: Adrien Ricciardi <aricciardi@baylibre.com>
Expand testing for QDEC at nrf platforms.
It uses general sensor API,
however there are also nrf driver specific assumptions.
Signed-off-by: Piotr Kosycarz <piotr.kosycarz@nordicsemi.no>
Modify the bt_bap_scan_delegator_add_src to take an address and
a sid instead of a PA sync object, so that the scan delegator
can add a source without syncing to the PA.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Raise the descriptor table span to 201 due to the inclusion of the USB
configuration descriptor.
Tested with:
$ west build -p -b it82xx2_evb tests/subsys/usb/desc_sections
-T usb.desc_sections
Signed-off-by: Ren Chen <Ren.Chen@ite.com.tw>
This change adds a Kconfig option "USB_CONFIGURATION_STRING_DESC_ENABLE"
to enable the USB configuration string descriptor. The default
configuration string is specified in "USB_CONFIGURATION_STRING_DESC."
Signed-off-by: Ren Chen <Ren.Chen@ite.com.tw>
If config library is disabled but DHCPv4 client is enabled,
then start DHCPv4 when zperf application starts.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Iface name which is used by native posix ethernet driver can only be
specified at compile-time. I wanted to run two instances of the same
program on native posix but did not want to make two separate builds only
to change the iface name. I have implemented getting the iface name from
command line.
Signed-off-by: Kacper Dalach <dalachowsky@gmail.com>
Packets are routed between OT and Zephyr net stacks.
For IPv4 these packets are managed by NAT64 by default.
Signed-off-by: Marcin Gasiorek <marcin.gasiorek@nordicsemi.no>
Update to enable CANXL_INT_RXSMB_OVER and
CAN_INT_ERR_FAST(ERR for CAN-FD).
Statistic CAN errors and count CAN TX and RX errors via
BCANXL that uses CANXL MRU to exchange informations with CAN host.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
