Added the STM32G0X SOC series to the list of SOC that need to disable the
ADC while setting the oversampling bits to prevent writing over the
CKMODE bits.
Signed-off-by: Alexandre Poizat <apoizat@kalrayinc.com>
Skip the "test_can_dtiming" test case if CONFIG_CAN_FD_MODE is not enabled,
not the "test_can_timing_missing_value" test case.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
There is a #endif comment which was incorrectly marked with
CONFIG_HW_STACK_PROTECTION instead of
CONFIG_ARM64_STACK_PROTECTION, which is used at #if.
So update it.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
cpuapp/cpurad can be debugged using the J-Link runner.
Note:
This feature is still experimental and has known issues. For example,
setting a breakpoint to main requires to patch init.c with a loop
polling a variable so that we stop there until unset from GDB.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Fixes an issue with paths being output in windows-style with back
slashes, this causes issues for certain escape sequences when
cmake interprets them. Replace these paths with posix paths so
that they are not treated as possible escape sequences.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Commit adds const qualifier to models metadata.
Specification claims: Composition Metadata Page 0
shall not change during a term of a node on the network.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Seen this in compiler
lib/posix/options/syslog.c: In function 'setlogmask':
lib/posix/options/syslog.c:66:16: error: 'oldpri' may be used uninitialized
66 | return oldpri;
| ^~~~~~
lib/posix/options/syslog.c:59:13: note: 'oldpri' was declared here
59 | int oldpri;
| ^~~~~~
lib/posix/options/syslog.c: In function 'vsyslog':
lib/posix/options/syslog.c:83:33: error: 'mask' may be used uninitialized
83 | if ((BIT(level) & mask) == 0) {
| ~~~~~~~~~~~~~~~~~~~~^~~~
lib/posix/options/syslog.c:71:17: note: 'mask' was declared here
71 | uint8_t mask;
| ^~~~
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Codecs can be printed at different levels:
level 0: Generic and unicast
level 1: subgroup codec configs
level 2: BIS codec configs
This commit ensures that the indentation level
is correctly increase based on where the codec configuration
data is printed.
This also updates the documentation for the BAP shell.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
print_codec_cfg and print_codec_cap has been modified to print the
codec metadata in a more human-readable way, so it is easier to read.
This also adds the (final) human readable support when
parsing and printing BASEs.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
print_codec_cfg has been modified to print the codec configs in a more
human-readable way, so it is easier to read.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
print_codec_cap has been modified to print the remote caps in a more
human-readable way, so it is easier to read and understand the remote
server's capabilities.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Modify the broadcast_sink_streams to be an array of shell_stream
instead of bt_bap_stream, so that it can be used in a similar way
as the rest of the streams.
To help the transition, a new helper function,
bap_stream_from_shell_stream, was added.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add additional logging in past_available to easily see the PAST
support of the broadcast assistant and scan delegator devices.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The function did not have a NULL check for the parameters,
and thus did not fail correctly on invalid input.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The simple test is there to test the API and simple extensions in
unison. Hello world was intended to be the first not the only extension
being tested.
Also refactors the entry thread to allow for usermode potentially by
passing the pointer to the function symbol rather than having it look it
up directly.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
The ISR prototype is not matching the
signature for interrupt handlers, which results in
build warnings.
Let's fix it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This currently calls timeout_rem() then adds back the result of
elapsed() to cancel out the subtraction of another elapsed() call
within timeout_rem(). Better not to make any calls to elapsed() in
that case, especially given that elapsed() may incur hardware access
overhead through sys_clock_elapsed().
Let's move the elapsed() subtraction to the only user of timeout_rem()
that needs it and remove its invocation from the z_timeout_expires()
path entirely.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
When we receive the subnet mask option from the server, we
cannot yet set the netmask to the network interface as the
mask is tied to the IP address we received from the server.
We need to delay the setting of netmask until we have added
the requested IP address to the interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This enables the use of CONFIG_XTENSA_MORE_SPIN_RELAX_NOPS to
specify how many NOPs for arch_spin_relax(). This is to keep
the atomic_cas() (via s32c1i) from saturating the internal bus
with contant RCW ops. The numbers should be further tuned
for specific application but these should provide a good start.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Fix issue related to "generic SPI" mode only, when a packet of
1512 bytes is received, net_pkt_write() fails and thrwos the error:
"Still some length to go 2".
This is due to net_pkt_rx_alloc_with_buffer() allocating a maximum
mtu/size of 1514, and driver is not removing 4 bytes of crc32 from
rx buffer, that comes to be 1516 (2 bytes over buffer limit).
Fix generic SPI rx frame size removing crc32 bytes.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Add Open Alliance spi protocol support.
Open Alliance is a chunk-based SPI protocol, based on sending
over SPI an ethernet frame divided in smaller chunks, using a
specific 32-bit header for each chunk transferred. All chunks
can be sent or received by a single dma transfer.
Default mode is set to Open Alliance SPI without protection,
since the adin2111 dev. board comes shipped this way.
Tested:
- Open Alliance SPI, no protection (default board shipped)
- Open Alliance SPI, protection
- Generic SPI, no crc
- Generic SPI, with crc8
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
After some debugging related to non-working "Generic SPI without CRC"
mode in eval_adin2111_ebz (CONFIG_ETH_ADIN2111_SPI_CFG0=n), noticed
that even after proper STATUS0 RESETC bit detection, registers,
for a certain period (some msecs) still reads as zero.
This patch fixes adin2111_await_device and with it the
"Generic SPI without CRC" mode.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Enable appending of a crc32 at the end of the frame by the MAC,
always. This is always needed since the driver is not adding it.
This field has nothing to do with Generic SPI protocol-related
8-bit CRC, so this patch removes the CONFIG_ETH_ADIN2111_SPI_CFG0
choice related to this setting.
Testing without this flag set, packets are not forwareded in the
network, since the driver is not appending any crc32 header
to the frame.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Move away from os.join.path and only rely on pathlib magic, and serialize
all paths using POSIX path separators.
This fixes documentation build and compliance check script on Windows.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
In the case that there are no more ISO buffers left,
"No available ISO buffers" is logged. However, given the
nature of ISO where we are (very) likely to get additional ISO
very soon after (typically every 7.5 or 10ms for audio),
this will get logged a lot, and the logging may in some
cases actually prevent the application from handling and
freeing existng buffers due to the immense logging,
which may make this (minor) issue into a blocking issue.
This is fixed by reducing the logging to the first
occurence, and then only every 100 afterwards, which has
shown to reduce the risk of this effectively blocking
the application.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Adds a function to set the syslog server ip with a struct sockaddr,
so that it can be set without a string.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
In case the LL address is not set on a packet for any reason, don't try
to access address structure to determine packet type.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Nordic Semiconductor no longer offers support for this board, so warn
users to avoid it for new prototypes.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Shell stack size is too low for OpenThread without joiner
functionality, causing overflow.
In this commit, the value of stack size is not changed.
Incorrect assigning of value for opentrhead with
no joiner functionality has been removed.
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
In order to avoid defining almost the same overlays for different
sample codes and/or applications a common overlay file per
display interface is defined under the boards dts folder.
In doing so, an application/sample code will only have to
define another overlay explicitly under application's board
folder if more blocks are to be enabled. In either case, users
should explicitly invoke the requested overfiles at 'west build'
invokation by using the DTC_OVERLAY_FILE system variable.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
Define a single node that reflects the LCDC IP. Instead of defining
the same IP block twice with different compatibles (mipi dbi, display)
we define a single node for the default display interface and
other interfaces like the MIPI DBI should override the compatible entry
with the appropriate one within its DTS overlay file.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
Exhibit Renesas LCD controller's driver implementation. The driver
is intended to employ the controller in the continuous mode so
it can drive display panels in the parallel RGB mode.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
Add a sample application to demonstrate some basic
C and shell interfaces for manipulating environment
variables.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
This PR adds declarations for the application conformance
feature test macro _POSIX_C_SOURCE.
It needs to be defined to value greater than or equal to 200112L
by the appplication.
However, Zephyr currently does not have a simple and consistent
means of specifying this value for POSIX samples, tests,
applications, and other libraries.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
