Firstly, build-asserting the execution/source memory sizes to be equal
wasn't working, due to the wrong (non-inst) DT API being used.
Secondly, this assert can be relaxed so that the source memory region
only needs to have greater than or equal size to the execution region,
as VPR firmware needs to fit into execution memory first and foremost.
This will come in handy, since MRAM partitions (typical source memory)
have stricter alignment requirements than RAM regions.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Add a note about the ``sample-point`` and ``sample-point-data`` CAN
devicetree properties now being optional.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove all optional, initial CAN sample point properties and rely on the
CAN timing calculations to automatically pick the preferred sample point
location based on the initial bitrate.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Make the properties for setting the initial sample points for both the
classic/arbitration phase and the data phase optional.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This driver enables CONFIG_GPIO, so if we try
to target a board which does not support it it
will fail.
Let's add the required tag in the testcase yaml.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Ignore userspace tag completely. Disabling USERSPACE in board kconfig is
not right, this will always be overidden by the application and we will
have build failures. The HW supports userspace and most filters in tests
depend on this capability.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Mark `sched_setparam()` , `sched_setscheduler()`
and `sched_rr_get_interval()`
have implemented but will fail with ``ENOSYS``
Were missing on the documentation before.
signed-off-by: Gaetan Perrot <gaetanperrotpro@gmail.com>
Mark `putmsg()` as implemented but will fail with ``ENOSYS``
Was missing on the documentation before.
signed-off-by: Gaetan Perrot <gaetanperrotpro@gmail.com>
On Intel ADSP platforms, additional "isync" is needed in interrupt
vector to synchronize icache when core is woken up from deeper
sleep state by an interrupt. This is only needed if DSP clock
gating is enabled.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Previous adjustments to hwmv2 lost this Kconfig file.
Test: west build -p always -b it82xx2_evb samples/hello_world
config BOARD_IT82XX2_EVB
select SOC_IT82302_AX
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Broadcom boards live in /boards/brcm, not /boards/broadcom
This commit fixes bad links accordingly.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Wurth Electronik boards live in /boards/we, not /boards/wurth_elektronik
This commit fixes bad links accordingly.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
U-Blox boards live in /boards/u-blox, not /boards/ublox
This commit fixes bad links accordingly.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
http://www.analog.com/adt7420 does not exist anymore nor redirect to
https, so update the link to be https
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Aconno doesn't seem to be around anymore. Remove deadlink to product page.
Issue originally reported in #67099
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This board's docs are now to be found on Qorvo website, update links
accordingly.
Originally reported in #67099.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Updated 3 dead (404) links in the doc page for Arduino Nicla Sense ME.
Also uniformized indenting of sphinx links in the process.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
When non-primary core is powered down and restart with sequence of:
- PM state set to SOFT_OFF
- once target core is idle, cut power with soc_adsp_halt_cpu()
- power up core again with k_smp_cpu_resume()
The execution will continue from stored DSP core context, but
will hit an assert in z_smp_cpu_mobile() as the PS.INTLEVEL
is zero.
Fix this issue by storing and restoring PS register in this flow.
Link: https://github.com/zephyrproject-rtos/zephyr/issues/70181
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
This current sentence would need to be clarified a bit
further to be really correct:
It is only when building with the host C library that it
applies, but with native_sim we can build with other
libC's.
The twister tests definitions are testing only with
embedded C libraries,
and there is anyway no harm if somebody defines the heap
size even if using the host libC.
So as such it would seem better to just remove this
sentence.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Move the GPIO button dts nodes to the common dts file so it
be selected by either cpu core.
Also fix an error in the GPIO setting for one of the switches.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Update lpcxpresso55s69_cpu0 (and ns target) names in build commands in
the board documentation. Also, correct the documentation for dual core
images on this part, as it was out of date.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fix board identifier in overlays for the lpcxpresso55s69_cpu0 target.
Board identifiers were renamed with the following command:
for file in $(find . -name "lpcxpresso55s69_cpu0.*"); do;
mv $file ${file/_cpu0/_lpc55s69_cpu0};
done
Additionally, remove lpcxpresso55s69_ns overlay targets where they are
no longer needed (or rename them where they are)
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Include soc.h in nxp MRT driver, so that CMSIS register definitions will
be available in this file
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit enhances the accuracy of hardware cycle calculation before
setting the IT8xxx2 event timer. The next target cycle is calculated by
the last, elapsed, and expected timeout ticks. And then, the difference
in hardware cycles between the target cycle and the current cycle is set
into the event timer. This increased accuracy effectively resolves the
clock drift issue.
Tested with:
west build -p always -b it8xxx2_evb tests/kernel/timer/timer_api
-T kernel.timer.tickless
west build -p always -b it8xxx2_evb tests/kernel/timer/timer_behavior
-T kernel.timer.timer
Fixes#67474#67833
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Signed-off-by: Ren Chen <Ren.Chen@ite.com.tw>
fwrite parameters are "size_t size" and "size_t nmemb",
when writing a string we should set sizeof(char) and len(string).
The test is doing it wrongly and making the function read more
memory than it should.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Default MAX_DATA_SIZE might be too small depending
on application (e.g. handling the scan result with 12 APs detected)
Added config option for MAX_DATA_SIZE and warning for the user
Signed-off-by: Samy Francelet <samy.francelet@ik.me>
