Updated nxp lpadc driver, because the phandle type property
'nxp,reference-supply' was removed, and a new phandle-array
type property 'nxp,references' added.
Signed-off-by: Zhaoxiang Jin <Zhaoxiang.Jin_1@nxp.com>
Add new property 'nxp,reference-cells' for vref node.
Remove lpadc nodes 'nxp,reference-supply' property.
Add new property 'nxp,references' for lpadc nodes.
Signed-off-by: Zhaoxiang Jin <Zhaoxiang.Jin_1@nxp.com>
Add specifier cells for nxp vref, when some other
peripherals use the vref to provide reference voltage,
this cells can be used to pass-in vref target voltage.
Signed-off-by: Zhaoxiang Jin <Zhaoxiang.Jin_1@nxp.com>
With new BT SIG Qualification Workspace it is no longer possible to
export/import full project. Only ICS export/import is possible.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Adds missing i2c_sleep pins configuration definition required
to properly support power management operations for
Smartbond I2C controller on da14695_dk_usb board.
Signed-off-by: Mateusz Hołenko <mholenko@antmicro.com>
When CONFIG_NET_STATISTICS=y is enabled, build fails
due to wrong interface pointer.
Fixes#75515
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Fix build error due to cmake requiring a separate
overlay for each of this target's SOCs.
Error being fixed:
```
-- Board: sam_v71_xult, qualifiers: samv71q21
CMake Error at cmake/modules/extensions.cmake:2742 (message):
Board sam_v71_xult defines multiple SoCs.
Shortened file name (sam_v71_xult.overlay) not allowed, use
'<board>_<soc>.overlay' naming
```
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Fix build error due to cmake requiring a separate
overlay for each of this target's SOCs.
Error being fixed:
```
-- Board: sam_v71_xult, qualifiers: samv71q21
CMake Error at cmake/modules/extensions.cmake:2742 (message):
Board sam_v71_xult defines multiple SoCs.
Shortened file name (sam_v71_xult.overlay) not allowed, use
'<board>_<soc>.overlay' naming
```
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Make sure that the ATE metadata does not overflow the sector size.
Take into account the data length and also the mandatory reserved ATEs
in each sector.
Signed-off-by: Adrien Ricciardi <aricciardi@baylibre.com>
Instead of silently `#undef`ing PSA_CRYPTO_C when TF-M is in use,
enforce that rule at the Kconfig level.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Replace platform_allow with integration_platforms, what allow CI to
build samples on all platforms with test feature 'usbd' but still limits
number of platforms when it is invoked with the --integration option.
Replace/add some platforms that already have test feature 'usbd'.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
The broadcast sink sample no longer treats the broadcast_code_received
semaphore as a boolean.
Fixes#75469
Signed-off-by: Jens Rehhoff Thomsen <jthm@demant.com>
risc-v idle call is being fetched from arch/ implementation.
This soc file is not used and can be removed.
Fixes#75540
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
- Added a flash runner configuration for rw, mcx, lpc, kinetis and imxrt,
used for sysbuild multi-image projects like MCUBoot.
- Solved the mass erase issue.
- The sysbuild project "west flash --erase" command caused
the mass_erase->flash_img1->reset->mass_erase->
flash_img2->reset sequence.
It was fixed to the mass_erase->flash_img1->
flash_img2->reset sequence.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
When using an encrypted broadcast, the previous value is no
longer enough and caused a stack overflow.
Slightly increased the value.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Some public API functions do not modify the net_buf instances and can
declare these arguments as const.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Adding a semicolon after the do-while loop in the LV_DEV_INIT()
macro also supports multiple instantiation.
Signed-off-by: Stephan Linz <linz@li-pro.net>
This removes the prompts for the mt8195 and related kconfigs,
so these cannot be overridden from command line (though
technically they cannot be disabled as they are being selected).
This also prevents them from appearing in the build .config
file as not being set even when we are being for other SoCs.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Reorganize the EEPROM periheral documentation to make room for subpages
with additional details. Add a page describing the EEPROM shell module.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Utilize a code spell-checking tool to scan for and correct spelling errors
in all files within the `kernel` directory.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
exclude cyw920829m2evk_02 from build. For cyw920829m2evk_02
need `west bloobs fetch` (to get BT fw), which does not
allowed in CI.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Add document for boot M7 Core by using Linux remoteproc to address
some known issues when boot DDR Zephyr kernel.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Fixes: #75390
A wrong bit mask (wrong: IOMUXC_SW_PAD_CTL_PAD_PUS_MASK = 0x8) was used.
That bit mask is for PUE/PUS-type gpio registers, but this is the
section for registers with alternative PULL (PDRV) type layout.
Right bit mask: IOMUXC_SW_PAD_CTL_PAD_PULL_MASK
Signed-off-by: Nils Larsen <nils.larsen@posteo.de>
When syncing to a PA using PAST then the sync_info.recv_enabled
was always just set to true, regardless of what mode was set
during the subscribe parameters.
The mode(s) are now stored in an array (with the default value
as well) so that we can retrieve that information when the PA
has synced via PAST.
It was considered to put the `mode` value into the `bt_conn`
struct, but that would require an API change as the `bt_conn`
parameter for the subcribe function uses `const`.
This commit also modifies the guard for PAST to be the more
correct value CONFIG_BT_PER_ADV_SYNC_TRANSFER_RECEIVER instead
of just CONFIG_BT_CONN.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Don't zero initialise the static data structure, as statics are
explicitly initialised to 0 per the C standard, and checkpatch normally
complains about the pattern.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Return the documented error if `wdt_install_timeout` is called after
`wdt_setup`, instead of triggering the state assertion inside of
`nrfx_wdt_channel_alloc`.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Return an error code if `wdt_feed` is called before `wdt_setup`, instead
of triggering the state assertion inside of `nrfx_wdt_channel_feed`.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Utilize a code spell-checking tool to scan for and correct spelling errors
in various files within the `doc` directory.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Some AMP native simulator targets (like the nrf5340bsim net core)
will not produce a final executable if only one of the core images
is built, when IPC is enabled, as those images require the other
core image to be able to link.
So this test cannot be run when targetting that core alone
(without using sysbuild to build the other).
Let's filter out these targets to avoid twister building
but finding itself with no executable and error out badly
as it cannot run the test.
The filter condition is effectively:
If building for a native target, there must be an .exe being
produced.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Ensure that we call the host libC when allocating space
for a possible set of test arguments even if we are
building Zephyr with an embedded libC.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
native_posix (unlike native_sim) or its breathen (NATIVE_APPLICATION)
link together the "runner" code and the embedded code.
This means that when CONFIG_STATIC_INIT_GNU is set,
any host library code (like the llvm fuzzer) constructors will get
postponed to the Zephyr initialization.
These libraries are unlikely to work if we do this.
(the llvm fuzzer does not)
So let's instead not enable STATIC_INIT_GNU for these targets.
This means possible embedded library constructors will continue to be
picked during the link and be still called during the native runner
initialization instead of during the Zephyr OS initialization as they
were just before we introduced STATIC_INIT_GNU in
6e977ae2d5
Note that native_posix will be deprecated shortly and its users
are strongly encouraged to move to native_sim.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Utilize a code spell-checking tool to scan for and correct spelling errors
in all files within the `include/zephyr/drivers` directory.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Increase the number of network packets and buffers for better TCP
performance in the sample out-of-the-box.
Decrease the network buffer data size for better buffer management in
the sample (less buffer space wasted for L2 header). The only drawback
of this is reduced TCP TX performance, but less than 2 Mbps in my case.
Finally, enable speed optimizations for another small performance boost.
As the RAM requirements of the sample now increase considerably in the
default configuration, add a note in the readme file about it, and how
to make it fit into smaller boards.
Tested on nucleo_h723zg:
Before (current defaults):
UDP TX RX
76.47 Mbps 93.48 Mbps
TCP TX RX
76.18 Mbps 67.75 Mbps
After (new defaults):
UDP TX RX
76.08 Mbps 93.62 Mbps
TCP TX RX
74.19 Mbps 85.51 Mbps
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The bug should be fixed now, so it possible to have it enabled as
long as OTS is not registered with the feature flag.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The checks for callbacks in bt_ots_init did not correctly take the
ots_init->features.oacp into account for all callbacks, which
caused some issues.
Slightly optimized the check for ots->cb->obj_read by moving the check
and reducing the number of places the code calls oacp_read_proc_cb.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Allocating a buffer in the system workqueue thread should never
be done wiht a K_FOREVER as that may block the thread forever.
Replace the K_FOREVER with a K_NO_WAIT and slightly modified
the function to handle this case.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
