The current PHY is read only when automatic PHY
update procedure is enabled, 2M PHY is supported and
extended advertising is enabled and this is done after
application is notified about connection. This leads
to invalid connection info PHY data which always returns
1M PHY because when using extended advertising the connection
can be established on different PHY and host does not read
this value from the controller in most cases. In order to
have a current PHY value updated we need to read it in
connection complete event before the user application
is notified about connection.
Signed-off-by: Kamil Gawor <Kamil.Gawor@nordicsemi.no>
bring fix from mcu-tools/mcuboot:
- espressif:esp32: Move app entry point call back to
iram_loader_seg region
fixes#45349fixes#46093
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Deep Sleep mode stops SMB module clocks which could interrupt ongoing
I2C transactions, so have the I2C driver acquire a PM lock at the
beginning of a transaction and release it at the end in order to ensure
the module remains active.
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
The BT tiny configuration has been removed some time ago,
but documentation has been still referencing it.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Remove unconditional write to PCA95xx output registers in setup_pin_dir,
and only write to output registers if selected pin is configured as
an output.
Fixes#45774
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The commit replaces direct access to flash_img_context, for the
purpose of checking how much data has been written, with call
to the flash_img_bytes_written.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Enable testcases under tests/drivers/gpio/gpio_basic_api
To run in twister, "-X gpio_loopback" parameter is needed
Signed-off-by: Hu Zhenyu <zhenyu.hu@intel.com>
Recently OpenAMP introduced the possibility to set the sizes for TX and
RX buffers per created instance. Expose this also to Zephyr users by
using a DT property "zephyr,buffer-size".
For the sake of simplicity use the same DT property to set the buffer
size for both TX and RX buffers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Extends #43119 with PPB and IO values of
`memory-region-mpu`.
That allows MPU region definition with
PPB or IO attributes in the DTS.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
All `struct device` members except name, config and api are marked as
read-only references. This means that, in practice, a `struct device`
can only be initialized statically.
Device constness happens because `Z_DEVICE_DEFINE` defines `struct
device` as `const`. This means that one can't modify any field of a
`struct device` anyway, so constifying struct members doesn't add much
value, if any (unless I'm missing something).
This patch makes all `struct device` references mutable, so that no
assumptions on how `struct device` is used are made. In the future, one
could e.g. dynamically allocate devices and assign any of the device
fields at runtime.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
- Enable GPIO by default to be consistent with other vendors,
Some samples also require GPIO driver to be enabled by default.
- Enable HEAP_MEM_POOL usage. The heap memory is used by Flash
driver during from flash to flash write operation.
Signed-off-by: Yuriy Vynnychek <yura.vynnychek@telink-semi.com>
The automatic elevation of security and retry of ATT requests interferes
with some tests that expect authentication failures.
Affecting GATT/CL/GAR/BI-42-C
Signed-off-by: Herman Berget <herman.berget@nordicsemi.no>
Provided sample support for Telink tlsr9518adk80d board.
Set CONFIG_BT_TINYCRYPT_ECC=n (supported by BLE controller).
Signed-off-by: Yuriy Vynnychek <yura.vynnychek@telink-semi.com>
EATT is not a requirement for the Multiple Variable Length Read
procedure, but previously one had to enable CONFIG_BT_EATT to enable
support for it.
Signed-off-by: Herman Berget <herman.berget@nordicsemi.no>
logging.log_syst.mipi_syst is written in ztest framework, now it has
a good method to test automatically, no need to configure the harness
as console any more, so remove it.
Signed-off-by: Guo Lixin <lixinx.guo@intel.com>
This fixes Kconfig that allowed to build PACS without support for sink
or source PACS. Few conditionals that no longer apply were removed.
Enabling ASCS support in specific direction enables related PACS
support.
Since PACS does `depends on` anything, it's safe to make use of `select`
statement.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
This renames the UUID to follow the same naming scheme as for
BT_UUID_PACS_SUPPORTED_CONTEXT.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
In preparation for the support of RV32E optimize a bit the t* registers
usage limiting that to t{0-2}.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The NVS data lookup time grows linearly with the number of
allocation table entries to walk through, meaning that if
some data pair in the NVS changes frequently, access to
other data pairs that change rarely can take a lot of time.
It is particularly visible when the NVS is used as the
settings backend since the backend needs to perform multiple
NVS reads to find a requested key.
Implement a simple cache that stores an address of the most
recent ATE for all NVS IDs that fall into the given cache
position. CRC8/16 is used as a hash function used to
distribute NVS IDs across the cache entries.
The cache entries are only invalidated when an NVS sector
is erased as part of the garbage collector task.
Signed-off-by: Damian Krolik <damian.krolik@nordicsemi.no>
This patch adds DTS properties for using wake-up mode
and the autosleep function to the ADXL362 driver.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Set the TF-M profile type to none for TF-M integration samples.
If the default profile has been set to something else these samples may
fail.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Adjusted Bluetooth parameters that have an impact on MTU and DLE
negotiation during a connection.
Enabled the Packet Reassembly feature from mcumgr libraries in the SMP
Server sample with the Bluetooth transport configuration. This change
should increase the overall throughput of the DFU process over
Bluetooth.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
As per XMCLib documentation we need to check that data has been received
before reading the buffers.
Fixes test_uart_poll_in test in tests/drivers/uart/uart_basic_api.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Casting to uint16_t* can cause an unaligned usage fault when c is not
aligned to 2 bytes and can unintentionally overwrite data when c has a 1
byte memory size. Also there's no need to cast to uint16_t* because
returned words are 8-bit characaters as setup in the configuration.
Fixes the following usage fault error in tests/drivers/uart/uart_basic_api:
START - test_uart_poll_in
Please send characters to serial console
E: ***** USAGE FAULT *****
E: Unaligned memory access
E: r0/a1: 0x00000000 r1/a2: 0x2000078f r2/a3: 0x0c00453c
E: r3/a4: 0x00000000 r12/ip: 0x00000000 r14/lr: 0x0c003de5
E: xpsr: 0x41000000
E: Faulting instruction address (r15/pc): 0x0c003de4
E: >>> ZEPHYR FATAL ERROR 0: CPU exception on CPU 0
E: Current thread: 0x20000118 (unknown)
E: Halting system
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
