When the CAP acceptor role is enable, ASCS will verify
that the stream context type supplied by the client
matches the PACS available context.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Define the range of metadata LTV types from Generic
Audio assigned numbers. They were orignally defined in
lc3.h, but they are not lc3 specific, so was moved
to audio.h and properly documented.
This also redefined the existing (unused) types from audio.h
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Verify the metadata before copying it. This will allow the
unicast server to verify the data and potentially
reject it without modifying existing metadata.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Adding the CAP Acceptor role, which is a quite simple
role. The role instantiates the Common Audio Service (CAS)
The role will later be expanded to properly support
the use the Coordinated Set Member role via CSIS.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
A Devicetree section was added in release-notes-3.1 document,
but not reported in release-notes-3.2.rst.
Add it back, as this topic deserves its own section.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When PINCTRL is enabled, the SCL and SDA pin numbers are not available
in configuration structures used for nrfx drivers initialization.
In this case, these pin numbers need to be obtained from peripheral
registers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
For now, on stm32f4 series, we only define PLL_P, PLL_Q and PLL_R
source clocks are they are required by the driver to allow configuration
of respective PLL outputs.
No other source clock are supported yet.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move to use DEVICE_DT_GET instead of device_get_binding as
we work on phasing out use of DTS 'label' property.
Signed-off-by: Kumar Gala <galak@kernel.org>
Move to use DEVICE_DT_GET instead of device_get_binding as
we work on phasing out use of DTS 'label' property.
Signed-off-by: Kumar Gala <galak@kernel.org>
Change APL_GPIO_DEV_* defines to be DT_NODELABELs instead of
"label" strings. This lets us change users of these defines to
use DEVICE_DT_GET.
We update samples/board/up_squared/gpio_counter to use DEVICE_DT_GET
as part of this change.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add the CONFIG_BT_AUDIO_DEBUG_STREAM_DATA Kconfig option
to better debug bt_audio_stream without drowning the log
in the data being sent.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add the BT_DEBUG_ISO_DATA so that ISO can easier be debugged
without the logs being drowned in the ISO data being sent
and received (which is typically at a low interval like 10ms).
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
When CONFIG_INIT_STACKS is enabled all stacks should be filled with 0xaa
so that the thread analyzer can measure stack utilization, but the IRQ
stack was not filled and so `kernel stacks` on the shell would show that
the stack had been fully used and inferring an IRQ stack overflow
regardless of the IRQ stack size.
Fill the IRQ stack before it gets used so that we can have precise usage
reports.
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Signed-off-by: Dave Aldridge <quic_daldridg@quicinc.com>
Uses the dt_compat_enabled Kconfig preprocessor to set defaults
for each HDA driver.
Each direction is uniquely selectable which can be useful when building
with SOF where only some directions may wish to be enabled at any given
time.
By default, given the device tree (intel_cavs.dtsi) only the host
directions are enabled but an overlay may adjust that as needed.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Move to use DEVICE_DT_GET instead of device_get_binding as
we work on phasing out use of DTS 'label' property.
Signed-off-by: Kumar Gala <galak@kernel.org>
Move to use DEVICE_DT_GET instead of device_get_binding as
we work on phasing out use of DTS 'label' property.
Signed-off-by: Kumar Gala <galak@kernel.org>
Create a sample level compatible for the motor controller and make use
of i2c-dt-spec facilities.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
For left/right gpio values:
- GPIO API returns `int` (signed).
- Drop array as only first index was used.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify left/right GPIOs in DT (zephyr,user node). Make use of
gpio-dt-spec and cleanup the code.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify PWM parameters in Devicetree. Code has been updated to operate
in native PWM units (nsec) everywhere.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify PWM parameters in Devicetree. Period in DT is used as the
initial period. Code has been updated to operate in native PWM units
(nsec) everywhere.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Not all platforms support setting the LSE driving capability, causing
the build to fail for platform such as the STM32L072 if compiled with
CONFIG_STM32_LPTIM_CLOCK_LSE=y.
Adding an #ifdef guard around the call to skip it if not defined in the
HAL.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
In npcx series, not all GPIO pads support Multi-Input Wake-Up Unit
(MIWU) functionality. Hence, this CL adds checking whether GPIO's pad
configuration is valid first before using it.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Move to use DEVICE_DT_GET_ONE instead of device_get_binding as
we work on phasing out use of DTS 'label' property.
Signed-off-by: Kumar Gala <galak@kernel.org>
