Do simple conversion of driver to have driver enabled by devicetree
in Kconfig and struct device created based on basic devicetree
data.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add dts bindings for the NIOS2 QSPI controller and flash device and
add nodes to the dts files for these devices as well.
Signed-off-by: Kumar Gala <galak@kernel.org>
This is this initial sysbuild guide on what sysbuild is and how to build
a sample using sysbuild.
It provides an architectural overview of sysbuild.
Descriptions on how to use `west build` or `cmake` + `ninja` to build
projects with the sysbuild infrastructure.
Flashing is described through the use of `west flash`.
Extending sysbuild with additional Zephyr based applications are
described, and reference to CMake documentation for including non-Zephyr
based applications are provided.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This commit disables the `tests/posix/common` test for the `qemu_leon3`
platform because of the alignment-related failure reported in the
GitHub issue zephyrproject-rtos/zephyr#48992.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Now that ft8xx drivers are enabled based on devicetree
we need to remove any cases of them getting enabled by
Kconfig.defconfig* files as this can lead to errors.
Signed-off-by: Kumar Gala <galak@kernel.org>
* Utilize DT_HAS_<COMPAT>_ENABLED for devicetree based drivers
* Move to using 'select SPI' instead of 'depends on'
(see commit df81fef944 for
more details)
Signed-off-by: Kumar Gala <galak@kernel.org>
Now that eeprom drivers are enabled based on devicetree we can
remove any cases of them getting enabled by proj.conf files.
Signed-off-by: Kumar Gala <galak@kernel.org>
Now that eeprom drivers are enabled based on devicetree
we need to remove any cases of them getting enabled by
Kconfig.defconfig* files as this can lead to errors.
Signed-off-by: Kumar Gala <galak@kernel.org>
We drive the default setting of CONFIG_PM_CPU_OPS_PSCI via devicetree
so there is no need to set CONFIG_PM_CPU_OPS_PSCI in defconfig files.
Signed-off-by: Kumar Gala <galak@kernel.org>
The INPUTMUX_PINTSEL_COUNT macro name variation is now handled
inside zephyr. Revert this change to the NXP SDK file.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
The macro INPUTMUX_PINTSEL_COUNT is name INPUTMUX_PINT_SEL_COUNT
on certain SoC's in the SDK.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
There are several test cases that create fake ethernet devices and
expect the fake device to be the only ethernet device enabled. Some
tests handle this be explicitly disabling actual ethernet drivers,
but this doesn't scale well.
Change drivers/ethernet/Kconfig to utilze a menuconfig option that
wraps all the drivers. This allows us for those test cases that
don't want any actual ethernet drivers to disable them with a
simple CONFIG_ETH_DRIVER=n.
Note, the fake ethernet devices utilize CONFIG_ETH_INIT_PRIORITY so
we have it outside of the 'if ETH_DRIVER' block.
Signed-off-by: Kumar Gala <galak@kernel.org>
In case peer does not send the MSS option, the TCP stack should assume
default peer MSS value of 536, as per RFC 1122:
If an MSS option is not received at connection setup, TCP
MUST assume a default send MSS of 536.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Synchronized up to: b03c098
- add support for generic watchdog alias
- direct inclusion of the hooks file
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Update to Sphinx 5.x, also update breathe since version 4.34 is the
first to officially support Sphinx 5.x.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Starting with Sphinx 6.0, extlinks caption with %s will be required.
Sphinx 5.x already warns about this requirements, so fix it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Upcoming versions of breathe highlight code embedded in Doxygen blocks.
In this case, the Devicetree fragment contained invalid syntax leading
to Sphinx warnings.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a sample to demonstrate use of (LP)U(S)ART with wakeup capability
This sample is provided with 2 configurations
- nucleo_wb55rg: Basic configuration that could be exercised in CI
- stm32l562e_dk: "Full feature" configuration that require some set up
configuration (be able to display console from lpuart) and allows to
achieve lowest power consumption.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When dealing with pm action 'suspend', driver applies device pinctrl sleep
state.
Using PM_DEVICE modes should allow to save more current consumption, and
applying pinctrl sleep state is one of the gains, but sleep state not being
available on a device is not a sufficient reason to block PM transition
to lower power mode.
If this pin state is not provided for the device, warn but don't block
pm transition. This will save some time to users setting up this feature
for the first time. Warning will give the opportunity to users to fine
tune their setup in a later step.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
These boards enable lptim node, but don't propose 'power-states'
description, making it useless and not testable regarding configuration
of existing, in tree, PM tests.
Clean up this definition.
They will be put back along with 'power-states', when possible to test.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Low power related nodes don't depend on Trust Zone activation.
Factorize into -common.dtsi when possible.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert lptim configuration from Kconfig to device tree.
Note that some boards were using Kconfig default value (LSI),
which now has to be made explicit using device tree.
If not done already, enable the required clock node (lse/lsi).
Clean up related Kconfig bits when required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Instead of relying on Kconfig, use dt inputs to configure LPTIM domain
clck (LSI/lSE).
Clock control dedicated APIs are used for configuration and get the
frequency of domain clock in use.
Constants macros used previously to store frequency and time base are
converted to static global variables.
Some code was set up specifically to keep compatibility with targets
that still use Kconfig to configure domain clock. This will be removed
after a deprecation period.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Continue conversion of LPTIM driver to device tree based configuration.
Get clock configuration from device tree and use clock_control API for
bus clock configuration
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Start converting LPTIM driver to device tree based configuration and
support of other instances.
First: get base address and IRQ using dt instance
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This reverts commit 87c6789355, restoring
commit 3b341085a2.
Restore the original change now that the underlying issue has been fixed
in 6cfb18686e.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This reverts commit 5b2ba9aaeb, restoring
commit 0224f2c508.
Restore the original change now that the underlying issue has been fixed
in 6cfb18686e.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The app_smem linker script files were being generated by a python
script based on the contents of the cmake-generated
compile_commands.json file. But it forgot to include a dependency on
the input. It also has the misfeature of being generated at cmake
interpretation time with a real but empty stub.
This worked for quite a while, because the dependency on "kernel"
(it's not clear to me why this was there but I'm not brave enough to
remove it) forced the file to rebuild any time any of the C code in
the system changed, which was almost always guaranteed.
But then commit 0224f2c508 ("device.h:
rework the device_extern.h mechanism") came along and removed a
generated include from device.h and saved a bunch of build time. And
it also meant that no kernel code was being compiled anymore. So now,
a second build picked up that empty stub file and failed with linker
warnings about the orphan sections that didn't find a place in the
link.
But second builds after cmake re-invocations are an obscure edge case,
right? Well, no. It turns out that this is exactly what "twister -f"
does in CI, in order to get retries for test cases that fail
spuriously (mostly for unavoidable host timer-related glitches on SMP
platforms).
So the end result was that this problem showed itself as a silent
failure of the retry mechanism in twister/CI, making it look for all
the world like the timer tests had all suddenly gone flaky.
Fun times.
Signed-off-by: Andy Ross <andyross@google.com>
Remove the calls to configure the pinmux for GPIO for the RV32M1. These are
no longer needed after 9ba953d13a.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
